Projectiondesign cineo Handbuch
RS232 and LAN
communication protocol
2
1 REVISION HISTORY 4
2 SETTING UP LAN COMMUNICATION 5
2.1 SETTING THE IP ADDRESS 5
2.2 CONNECTING TO THE PROJECTOR 6
3 HOW TO USE THE PROJECTORS LAN FUNCTIONALITY 7
4 SETTING UP RS232 COMMUNICATION 8
4.1 CONNECT TO THE PROJECTOR 8
4.2 RS232 COMMUNICATION PARAMETERS 8
5 SEND AND RECEIVE BINARY PACKETS 8
5.1 ABOUT THE PROTOCOL 8
5.2 SET_OPERATIONS 8
5.3 GET_OPERATIONS 8
5.4 INCREMENT_ AND DECREMENT_OPERATIONS 9
5.5 EXECUTE_OPERATIONS 9
5.6 DESCRIPTOR_OPERATIONS 9
5.7 EXAMPLE OF SETTING PROTOCOL PARAMETERS AND SENDING A COMMAND IN CMD WINDOW 9
5.8 OSD FEEDBACK 9
6 SEND AND RECEIVE ASCII COMMANDS 10
6.1 OVERVIEW 10
6.2 MESSAGE BODY 10
6.3 MNEMONIC 10
6.4 MODIFIER 11
6.5 ADDRESSING 11
6.6 ACKNOWLEDGE/RESPONSE 11
6.7 SUPPORTED COMMANDS 12
6.8 EXAMPLES 16
6.9 AMX/CRESTON 20
6.10 TRUTH-TABLES FOR ABS-VALUES 20
TABLE OF CONTENT
3
APPENDIX A, BINARY OPERATION PACKET TYPE 21
A.1 OPERATION PACKET TYPE 21
A.2 OPERATION PACKET PAYLOAD FORMAT 21
APPENDIX B, BINARY PACKETS IN HEXADECIMAL VALUES 22
APPENDIX C, RS232 DAISY CHAINING 28
C.1 ABOUT THE PROTOCOL 28
C.2 ADDRESS MODES 28
C.2.1 AUTO ADDRESS MODE 28
C.2.2 FIXED ADDRESS MODE 28
C.2.3 BROADCAST 28
C.3 BAUD RATE 28
C.4 SPECIAL SHORT MESSAGES 29
C.5 EXAMPLES 29
APPENDIX D, ADJUSTING CUSTOM COLOR TEMP USING RS232 20
D.1 CHOOSE “CUSTOM COLOR TEMP” 20
D.2 ADJUST THE COLOR TEMPERATURE BY USING THE INCREMENT / DECREMENT OPERATIONS: 20
APPENDIX E, TRUTH TABLES 32
E.1 OSD WARNING ON 32
E.2 LAMP IGNITION STATES 32
E.3 THERMAL MONITOR STATES 32
E.4 LAMP ON STATE S 32
4
1 REVISION HISTORY
Document Rev Release Date Revised Owner
LAN and RS-232 communication protocol and command set 1.0 15/02/06 Initial F3
5
Description Value
IP address 192.168.1.90
Subnet mask 255.255.255.0
Default gateway 192.168.1.1
TCP port 1025
UDP port 1225
Username admin
Password admin
The projector is shipped with a set of default settings, these are as follows:
Before you connect the projector to your LAN make sure that the IP address 192.168.1.90
is not already in use. If you need to change it, you have to make sure that the computer you
use is on the same subnet. This means that the computer need to have an IP address in
the range from 192.168.1.1 to 192.168.1.254.
2 SETTING UP LAN COMMUNICATION
2.1 Setting the IP address
If you need to change the computers IP address, follow these steps:
1. Right click on “Network Neighborhood” / “My Network Places” on your computer, and
then select “Properties”.
2. Doubleclick on the network connection that represents your LAN, select “properties”,
then doubleclick “Internet Protocol (TCP/IP).
3. This will take you to a screen where you can set the computers IP address:
Set the IP address and click OK on this and the previous dialog when you’re done.
6
2.2 Connecting to the projector
You have two options regarding how to make the physical connection to the projector.
You can either use a crossover twisted pair (TP) cabel directly from the computer to the
projector, or two straight-through TP cables with a HUB or a switch between them.
Now the computer should be on the same subnet as the projector, and you are ready to
configure it. This is done by starting up an internet browser, like Internet Explorer, Opera,
Firefox or similar. Then type the projectors default IP address (192.168.1.90) in the address
bar.
You will then be presented with the login screen shown below:
Type in the projectors default login name (admin) and password (admin), both are case
sensitive.
If both are correct, you will se a configuration website like this:
On this page you can setup the projectors IP address, subnet mask, default gateway,
projector port (TCP), rimi port (UDP), and password. This page also displays the current
version of network firmware the projector is running.
7
Other network options:
As you can see from the default settings table, the projectors also support commands over
the UDP protocol. HyperTerminal doesn’t support UDP but there are other applications like
the ones from SimpleComTools.
There is also quite easy to integrate this functionality if you are designing an application
yourself.
With a Crestron, AMX and other control system you now have the option to control the
projector via Ethernet in addition to RS232 using the same command set.
Once the projector is setup correctly and connected to the LAN, it’s ready to receive
commands. The LAN commands is exactly the same as for RS232 control, although you
may have to pass on the commands to the projector with a different application.
HyperTerminal that comes with Windows, can be used for this.
3 HOW TO USE THE PROJECTORS LAN FUNCTIONALITY
- Start up HyperTerminal, click ”File” and
then ”New Connection”. Give it a name
and press OK. You will then see this dia-
log, here you choose TCP/IP (Winsock).
- Now type in the projectors IP address in
the ”Host address:” field, and the projec-
tors TCP port in the ”Port number:” field.
Press OK when you’re done.
To send an eOperation to the projector, select
”Transfer” and then ”Send Text File...”.
You will then be presented with a dialog which you can choose the file you want to trans-
fer. Choose your command, click ”Open”, and the command will be transfered.
8
4 ESTABLISH COMMUNICATION
The projector may be controlled either through the LAN or the RS232 interfaces. Both
interfaces can not be used at the same time. Select between LAN or RS232 control in the
menus system (se the projector user guide for further information).
4.1 Connect to the projector
Connect the projector and host using a standard serial cable with 9-pin female to the host,
and 9-pin male to the projector. Pin 2 connects to pin 2, pin 3 connects to pin 3 and pin 5
connects to pin 5.
The projectors can be daisy-chained using RS232. Please, refer to Appendix C for de-
tailed information about RS232 daisy-chaining.
4 SETTING UP RS232 COMMUNICATION
Baud rate is configurable from the projector’s menu system. Default baud rate is 19200.
This section applies to single projector control with no address information. Please, refer
to Appendix B for detailed information about RS232 daisy-chaining.
5.1 About the protocol
The RS232 protocol is a binary protocol where each command is a series of 32 bytes in
one packet. See Appendix A for command structure. The tables in appendix B have one
row for each command.
The packet consists of a header with 7 bytes, and the packet payload, 11 bytes (see ap-
pendix A). It is important to complete the packet with an additional 14 bytes of padding,
so that the total packet size reaches 32 bytes.
The bytes are numbered 1 through 32. Byte 1 is sent first, byte 32 last. Some columns in
Appendix B show the value to be sent for several consecutive bytes. These are typically
indicated by a range, ie. 14 - 16. This means that bytes 14-16 all have the same value.
The protocol allows for both SET and GET operations. To utilize GET operations the host
needs a routine for receiving and interpreting incoming packets.
5.2 SET_operations
SET_operations are used to force the projector into different modes, like setting bright-
ness and contrast setting, switching between sources, etc.
As seen in Appendix B, each packet is a series of 32 bytes. To control the projector,
simply send the desired packet to the serial port. (An example of how to do this from a
DOS-window is provided in chapter 5.7)
After receiving a packet and executing the operation, the projector will immediately send
a packet in return. The returned packet will contain a PAK (0x1E) (PAK = Packet Acknowl-
edge), followed by the initial SET_operation sent from the host. Total packet size is 33
bytes.
5.3 GET_operations
GET_operations are used to acquire data or status from the projector, such as lamp us-
age hours, total on time, etc.
A response to a successful GET_operation consists of a PAK (0x1E) followed by the initial
GET_operation sent from the host. The requested value resides as a WORD in byte 17
(low byte) and byte 18 (high byte). Total packet size is 33 bytes.
4.2 RS232 Communication parameters
Parameter Data
Baud rate 4800, 9600, 19200
Parity N
Databits 8
Stopbits 1
Flowcontrol None
Table 1: RS232 parameters
5 SEND AND RECEIVE BINARY PACKETS
9
5.6 DESCRIPTOR_operations
To aquire the valid range of an operation, set byte 8 (operation type) to 7 (DESCRIPTOR)
fill in the operation number and send the packet. A successful response will consist of
PAK (0x1E), followed by the standard 32 bytes.
5.7 Example of setting protocol parameters and
sending a command in CMD window
Setting up the COM port, and sending a “poweron” command, where “poweron” is sim-
ply a binary-file with the appropriate packet for turning the projector on:
This returns, when successful, an acknowledgement as described in chapter 5.2 ,
and turns the projector on.
5.8 OSD feedback
RS232 control commands will not produce any OSD feedback. Only keypad and IR
remote control will produce OSD feedback.
5.4 INCREMENT_ and DECREMENT_operations
These operations are used when you want to increment or decrement the excisting value.
The response consists of a PAK (0x1E) followed by the initial operation sent, except for
byte 11, which carries an operation validation code, 0x01. Total packet size is 33 bytes.
5.5 EXECUTE_operations
An EXECUTE_operation triggers a pre-programmed algorithm in the firmware to execute
a certain chain of events. The EXECUTE_operation does not contain any parameters to
indicate a desired value, but simply executes the algorithm assigned to it.
The response is equal to that of the INCREMENT/DECREMENT_operations (see 5.4).
10
Field Description Comment
<HEADER> ASCII character ‘:’ Required
Separator ASCII character ‘space’ Optional
Address 1-3 bytes address Optional
6.3 MNEMONIC
The Mnemonic is 4 bytes key identifier, know as the ASCII command.
Example: POWR, SABS, IVGA
<HEADER> [SEPARATOR] ADDRESS [SEPARATOR] MESSAGE
BODY
1 byte 1 byte 1-3 bytes 1 byte N bytes
6.1 Overview
The protocol exists in parallel with the already existing 32/33-byte protocol.
The protocol has the following definition:
6.2 Message body
The message body structure is as follows:
MNEMONIC [SEPARATOR] [MODIFIER] [SEPARATOR] VALUES CR
4 byte 1 byte 1 or 2 bytes 1 byte N bytes 1 byte
Field Description Comment
Mnemonic 4 bytes key identifier,
not case sensitive Required
Modifer Single char symbol Optional
Values 1-3 bytes address Optional
TERM Termination char 0x0D (CR) Required
6 SEND AND RECEIVE ASCII COMMANDS
Andere Handbücher für cineo
1
Dieses Handbuch passt für folgende Modelle
4
Inhaltsverzeichnis
Andere Projectiondesign Projektor Handbücher
Projectiondesign
Projectiondesign avielo spectra Bedienungsanleitung
Projectiondesign
Projectiondesign three 1080 Bedienungsanleitung
Projectiondesign
Projectiondesign evo2sx+ Bedienungsanleitung
Projectiondesign
Projectiondesign F1+ SXGA+ Bedienungsanleitung
Projectiondesign
Projectiondesign cineo3+ 1080 Bedienungsanleitung
Projectiondesign
Projectiondesign Action three 1080 Bedienungsanleitung
Projectiondesign
Projectiondesign one mk II Bedienungsanleitung
Projectiondesign
Projectiondesign Action three 1080 Bedienungsanleitung
Projectiondesign
Projectiondesign Action one mk III Handbuch
Projectiondesign
Projectiondesign F32 SX+ Bedienungsanleitung
Projectiondesign
Projectiondesign WUXGA 720/1080 SXGA+ Bedienungsanleitung
Projectiondesign
Projectiondesign Action one mk II Handbuch
Projectiondesign
Projectiondesign FS35 WQXGA Montage- und Bedienungsanleitung
Projectiondesign
Projectiondesign F1+ SXGA+ Bedienungsanleitung
Projectiondesign
Projectiondesign evo2sx+ Bedienungsanleitung
Projectiondesign
Projectiondesign F10 1080 Bedienungsanleitung
Projectiondesign
Projectiondesign F2 sx+ Handbuch
Projectiondesign
Projectiondesign F10 AS3D Bedienungsanleitung
Projectiondesign
Projectiondesign evo XGA Bedienungsanleitung
Projectiondesign
Projectiondesign Action one mk II Bedienungsanleitung
Beliebte Projektor Handbücher anderer Marken
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung
NEC
NEC NP600S EDU Bedienungsanleitung
BenQ
BenQ SH753P Bedienungsanleitung
Eiki
Eiki EK-623U series Bedienungsanleitung
Epson
Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung
Epson
Epson PowerLite Home Cinema 705HD Bedienungsanleitung
