ProLights EclPanel TWCMini2X1 Bedienungsanleitung
USER MANUAL
REV.01-01/22 English version
EclPanel TWCMini2X1
115W Tunable White and colourful LED soft
light with pixels and lighting effects
Thank you for choosing PROLIGHTS
Please note that every PROLIGHTS product has been designed in Italy to meet quality and performance requirements
for professionals and designed and manufactured for the use and application as shown in this document.
Any other use, if not expressly indicated, could compromise the good condition/operation of the product and/or be
a source of danger.
This product is meant for professional use. Therefore, commercial use of this equipment is subject to the respectively
applicable national accident prevention rules and regulations.
Features, specications and appearance are subject to change without notice. Music & Lights S.r.l. and all afliated
companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic loss or any other
loss occasioned by the use of, inability to use or reliance on the information contained in this document.
Product user manual can be downloaded from the website www.prolights.it , or can be inquired to the ofcial
PROLIGHTS distributors of your territory (https://www.prolights.it/sales_network.html).
Scanning the below QR Code, you will access the download area of the product page, where you can nd a broad
set of always updated technical documentation: specications, user manual, technical drawings, photometrics,
personalities, xture rmware updates.
The PROLIGHTS Logo, PROLIGHTS names and all other trademark in this document pertaining to PROLIGHTS services
or PROLIGHTS product are trademarks OWNED or licensed by Music & Lights S.r.l., its afliates, and subsidiaries.
PROLIGHTS is a registered trademark by Music & Lights S.r.l. All right reserved. Music & Lights – Via A. Olivetti, snc -
04026 - Minturno (LT) ITALY.
Visit the download area
of the product page
PROLIGHTS - Ecl Panel TWCM2X1 01
INDEX
SAFETY INFORMATION 02
1 - PACKAGING 05
PACKAGE CONTENT..................................................................................................... 05
OPTIONAL ACCESSORIES............................................................................................. 05
2 - TECHNICAL DRAWING 06
3 - INSTALLATION 07
MOUNTING.................................................................................................................... 07
4 - CONNECTION TO THE MAINS SUPPLY 08
5 - START UP 08
CONNECT AND DISCONNECT POWER FROM THE PRODUCT.................................. 08
6 - PRODUCT OVERVIEW 09
7 - DMX CONNECTION 10
CONNECTION OF THE CONTROL SIGNAL: DMX LINE .............................................. 10
INSTRUCTIONS FOR A RELIABLE DMX CONNECTION ............................................... 10
CONNECTION DAISY CHAIN........................................................................................ 10
CONNECTION OF THE DMX LINE................................................................................ 10
CONSTRUCTION OF THE DMX TERMINATION ........................................................... 11
DMX ADDRESSING ........................................................................................................ 11
ETHERNET OPERATION ................................................................................................ 11
ETHERNET TO DMX OPERATIONS ............................................................................... 11
OPERATION AS A WIRELESS TRANSMITTER................................................................ 12
IN TO WDMX ................................................................................................................. 12
OPERATION AS A WIRELESS RECEIVER........................................................................ 12
WDMX TO DMX (RX)...................................................................................................... 13
8 - CONTROL PANEL 14
DISPLAY AND BUTTONS LAYOUT................................................................................. 14
ROTATORY KNOB LAYOUT ........................................................................................... 14
9 - MENU STRUCTURE 15
10 - SHORTCUT 19
11 - DIMMER CURVES 19
12 - RDM FUNCTIONS 21
13 - DMX CHARTS 22
14 - ACCESSORIES INSTALLATION 43
POLE OPERATED YOKE (CODE ECLPANELM2X1POYO - OPTIONAL) ........................ 43
EGG CRATES (CODES EPTWCM2X1EC30, EPTWCM2X1EC60, EPTWCM2X1EC2C -
OPTIONAL)..................................................................................................................... 44
DIFFUSION FILTERS (CODES EPTWCM2X1FILTINT, EPTWCM2X1FILTERHD,
EPTWCM2X1FILTERMD, EPTWCM2X1FILTERLD - OPTIONAL) .................................... 45
BARN DOOR (CODE EPTWCM2X1BD - OPTIONAL) .................................................... 46
CENTER MOUNT BRACKET (CODE EPTWCBRKM - OPTIONAL)................................. 47
BALL HEAD JOINT (CODE EPTWCBHEAD - OPTIONAL) ............................................. 48
15 - MAINTENANCE 49
MAINTENANCE AND CLEANING THE PRODUCT........................................................ 49
REPLACING THE FUSE................................................................................................... 49
VISUAL CHECK OF PRODUCT HOUSING ..................................................................... 49
TROUBLESHOOTING..................................................................................................... 50
PROLIGHTS - Ecl Panel TWCM2X102
SAFETY INFORMATION
WARNING!
• Please read carefully the instruction reported in this section before installing, power-
ing, operating or servicing the product and observe the indications also for its future
handling.
This unit is not for household and residential use, only professional applications.
Connection to mains supply
• The Connection to the mains supply must be carried out by a qualied electrical
installer.
• Use only AC supplies 100-240V 50-60 Hz, the xture must be electrically connected
to ground (earth).
• Select the cable cross section in according with the maximum current draw of the
product and the possible number of products connected at the same power line.
• The AC mains power distribution circuit must be equipped with magnetic+residual
current circuit breaker protection.
• Do not connect it to a dimmer system; doing so may damage the product.
Protection and Warning against electrical shock
• Do not remove any cover from the product, always disconnect the product from AC
power before servicing.
• Ensure that the xture is electrically connected to ground (earth). And use only a
source of AC power that complies with local building and electrical codes and has
both overload and ground-fault (earth-fault) protection.
• Before using the xture, check that all power distribution equipment and cables are
in perfect condition and rated for the current requirements of all connected devices.
• Isolate the xture from power immediately if the power plug or any seal, cover, ca-
ble, or other components are damaged, defective, deformed or showing signs of
overheating.
• Do not reapply power until repairs have been completed.
• Refer any service operation not described in this manual to PROLIGHTS Service team
or an authorized PROLIGHTS service center.
Installation
• Make sure that all visible parts of the product are in good visible condition before its
use or installation.
• Make sure the point of anchorage is stable before positioning the projector.
• When suspending the xture above ground level, secure it against failure of primary
attachments by attaching a safety cable that is approved as a safety attachment for
the weight of the xture to the attachment point on the main frame of the product. ln
case the safety cable, enter in action, it needs to be replaced with a new one.
• Install the product only in well ventilated places.
• For non temporary installations, ensure that the xture is securely fastened to a load-
bearing surface with suitable corrosionresistant hardware.
• For a temporary installation with clamps, ensure that the quarter-turn fastener and/or
screws are turned fully, and secured with a suitable safety cable.
0,5 m Minimum distance of illuminated objects
• The projector needs to be positioned so that the objects hit by the beam of light are
at least 0.5 meters (1.64 ft) from the lens of the projector.
PROLIGHTS - Ecl Panel TWCM2X1 03
T 45°
C
a
Max operating ambient temperature (Ta)
• Do not operate the xture if the ambient temperature (Ta) exceeds 45 °C (113 °F).
T
-10°
C
a
Minimum operating ambient temperature (Ta)
• Do not operate the xture if the ambient temperature (Ta) is below -10 °C (-14 °F).
Protection from burns and re
• The exterior of the xture becomes hot during use. Avoid contact by persons and
materials.
• Ensure that there is free and unobstructed airow around the xture.
• Keep ammable materials well away from the xture
• Do not expose the front glass to sunlight or any other strong light source from any an-
gle. Lenses can focus the sun’s rays inside the xture, creating a potential re hazard.
• Do not attempt to bypass thermostatic switches or fuses.
Indoor use
• This product is designed for indoor and dry environments.
• Do not use in wet location and do not expose the xture to rain or moisture.
• Never use the xture in places subject to vibrations or bumps.
• Make certain that no inammable liquids, water or metal objects enter the xture.
• Excessive dust, smoke uid, and particle build up degrades performance, causes
overheating and will damage the xture.
• Damages caused by inadequate cleaning or maintenance are not covered by the
product warranty.
T
90°
C
c
Temperature of the external surface
• The surface of the xture can reach up to 90 °C (194 °F) during operation. Avoid
contact with people and materials.
Maintenance
• Warning! Disconnect the xture from AC mains power and allow to cool for at least
10 minutes before handling.
• Only technicians who are authorized by PROLIGHTS or Authorised service partners
are permitted to open the xture.
• Users may carry out external cleaning, following the warnings and instructions pro-
vided, but any service operation not described in this manual must be referred to a
qualied service technician.
• Important! Excessive dust, smoke uid, and particle build up degrades performance,
causes overheating and will damage the xture. Damages caused by inadequate
cleaning or maintenance is not covered by the product warranty.
Photobiological safety
• This device emits potentially dangerous optical radiation and is identied in the cat-
egory of Risk Group 1 according to EN 62471.
Do not stare at the operating light source
• Do not look directly at the LED source during operation. It can be harmful to the eyes
and skin.
• During Installation, operation and maintenance, be prepared for the xture to light
and move suddenly when connected to power.
Disposal
• This product is supplied in compliance with European Directive 2012/19/EU – Waste
Electrical and Electronic Equipment (WEEE). To preserve the environment please dis-
pose/ recycle this product at the end of its life according to the local regulation.
PROLIGHTS - Ecl Panel TWCM2X104
The products to which this manual refers comply with:
• 2014/35/EU - Safety of electrical equipment supplied at low voltage (LVD).
• 2014/30/EU - Electromagnetic Compatibility (EMC).
• 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS).
• 2014/53/EU - Radio Equipment Directive (RED).
The products to which this manual refers comply with:
• UL 1573 + CSA C22.2 No. 166 - Stage and Studio Luminaires and Connector Strips.
• UL 1012 + CSA C22.2 No. 107.1 - Standard for power units other than class 2.
FCC Compliance:
• This device complies with Part 15 of the FCC Rules. Operation is subject to the fol-
lowing two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may
cause undesired operation.
Other approvals
• The product meets the safety requirements of the certification procedures of the
market in which it is placed and sold.
PROLIGHTS - Ecl Panel TWCM2X1 05
1 - PACKAGING
PACKAGE CONTENT
• 1x ECLPANELTWCM2X1;
• 1x 1,5 meters power cable (BARE END - NEUTRIK POWERCON TRUE1 IP65);
• 1x ECLFRSPG: spigot for PROLIGHTS Fresnel series;
• User manual.
OPTIONAL ACCESSORIES
• WSBBR512G6: blackBox R-512 G6 receiver 512Ch, 2.45GHz,DMX&RDM,Bluetooth,G3,G4,G4S,G5,CRMX;
• WSBBF1G5: blackBox F-1 G5 transmitter, 2,45GHz & 5.2/5,8 GHz, DMX/RDM, 512Ch;
• WSBBF1G6: blackBox F-1 G6 transrec, 512ch, 2.45GHz, DMX&RDM,Bluetooth,G3,G4,G4S, G5, CRMX;
• WSBBR512G5: blackBox R-512 G5 receiver 512Ch, 2.45GHz & 5.8GHz, DMX/RDM optional;
• C6040: aluminum clamp for 28mm spigot, 200kg load, 48-51mm tubes;
• C6002: slim aluminium clamp, 200 kg loading, 48-51 mm tubes, M10 bolt;
• RSR0630A/B: steel security cable for hanging bodies, inox steel shackle, L=60 cm, silver/black;
• 9533FXWL03: ass. 3x2.5mm TH07 cable, SHUKO plug, MENAC3FXW socket, L.3m;
• 9513FXWL03: ass. 3x2.5mm TH07 cable, 16A 3p 230V CEE plug, MENAC3FXW socket, L.3 m;
• 958225L03: 3x2.5mm TH07 Cable, 16A 3p PwCon MXW, 16A 3p PwCon FXW, L. 3m;
• TOUR53415L03BK: dmx cable HC5340. CANC5MXX XLR 5p->CANC5FXX XLR (f) 5p, L.3m;
• FCLPANELM2X14U: ight case for 4 pcs of ECLPANELTWCM2X1;
• EPTWCBRKM: center mount bracket for ECLPANELTWC and ECLPANELTWCJR4X1;
• EPTWCBHEAD: ball head joint for center mount bracket EPTWCBRK series
• ECLPANELM2X1POYO: pole operated aluminium yoke bracket for ECLPANELTWCM2X1;
• EPTWCM2X1FILTINT: front intensied diffusion lter for ECLPANELTWCM2X1;
• EPTWCM2X1FILTERHD: front high diffusion lter (less output) for ECLPANELTWCM2X1;
• EPTWCM2X1FILTERMD: front low diffusion lter (more output) for ECLPANELTWCM2X1;
• EPTWCM2X1FILTERLD: front low diffusion lter (more output) for ECLPANELTWCM2X1;
• EPTWCM2X1EC30: 30 degree egg crate for ECLPANELTWCM2X1;
• EPTWCM2X1EC60: 60 degree egg crate for ECLPANELTWCM2X1;
• EPTWCM2X1EC2C: 2 chamber egg crate for ECLPANELTWCM2X1
• EPTWCM2X1BD: barndoor for ECLPANELTWCM2X1 with 4 directional aps to adjust the light beam;
• EPTWCSBM21: snapBag 2x1 for ECLPANELTWCM2x1 by DoP choice;
• EPTWCSG4SBM2140: 40° SnapGrid for SnapBag, 2x1 for ECLPANELTWCM2x1 by DoP choice;
• EPTWCSGM2140: 40° SnapGrid, 2x1 for ECLPANELTWCM2x1 by DoP choice;
• SWIT500W2KIT: 24/48V 500W battery (>1.2hrs) KIT including 2*PBH260S smart power batt.+st.adapt;
• SPGM10: 28mm spigot for xtures, M10 bolt;
• SPGM12: 28mm spigot for xtures, M12 bolt;
• UPBOX1U: Firmware uploader kit, USB IN, 3pin XLR DMX OUT, USB OUT.
PROLIGHTS - Ecl Panel TWCM2X106
2 - TECHNICAL DRAWING
Fig. 01
Weight: 6 kg - 13.22 lbs
Weight: 8.63 kg - 19.03 lbs
PROLIGHTS - Ecl Panel TWCM2X1 07
Fig. 02
3 - INSTALLATION
MOUNTING
Check that the supporting structure can safely bear the weight of all installed xtures, clamps, cables,
auxiliary equipment, etc. and complies with locally applicable regulations.
When suspending the xture above ground level, secure it against failure of primary attachments by
attaching a safety wire that is approved as a safety attachment for the weight of the xture to an anchor
point on the product main frame.
Do not use removable parts or weak anchors for secondary attachment.
Warning! When clamping the xture to a truss or other structure at any angle, use clamps of half-cou-
pler type. Do not use any type of clamp that does not completely encircle the structure when fastened.
RSR0630A/B
steel security cable
C6002
clamp
RSR0630A/B
steel security cable
C6040
clamp
RSR0630A/B
steel security cable
C6040
clamp
Ø10.5 mm
Ø0.41 in
PROLIGHTS - Ecl Panel TWCM2X108
5 - START UP
CONNECT AND DISCONNECT POWER FROM THE PRODUCT
To apply and disconnect power to the product:
• Check that the product is installed and secured as indicated in the Safety Informations, and that
personal safety will not be put at risk when the xture lights up.
• Connect the power connector into the Mains input socket (100-240 VAC-50/60 Hz).
• The product is then ready for its operations and can be controlled through the available input sig-
nals on board.
• To disconnect power from the product, disconnect the Mains from the socket.
• In case you wish to run the product through an external battery, then connect the product to an
external battery (24-36V) into the dedicated XLR4p socket; to disconnect power, disconnect the
Battery from the socket.
• In case you wish to run the product through an external PU, then connect the product to an external
PU (48V) into the dedicated XLR3p socket; to disconnect power, disconnect the PU from the socket.
4 - CONNECTION TO THE MAINS SUPPLY
WARNING: For protection from electric shock, the xture must be earthed!
The product is equipped with auto-switching power supply that automatically adjusts to any 50-60Hz
AC power source from 100-240 Volts.
If you need to install a power plug on the power cable to allow connection to power outlets, install a
grounding-type (earthed) plug, following the plug manufacturer’s instructions. If you have any doubts
about proper installation, consult a qualied electrician.
T max power consumption is 130W.
Core (EU) Core (US) Connection Plug terminal marking
Brown Black Live L
Blue White Neutral N
Yellow+green Green Earth
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere ProLights Beleuchtungsausrüstung Handbücher
ProLights
ProLights V200SPOT Bedienungsanleitung
ProLights
ProLights SOLAR48Q Bedienungsanleitung
ProLights
ProLights LUMIPAR12IRTRI Bedienungsanleitung
ProLights
ProLights ArcPod 48Q Bedienungsanleitung
ProLights
ProLights spider Bedienungsanleitung
ProLights
ProLights V575SPOT Bedienungsanleitung
ProLights
ProLights EclMini CC Bedienungsanleitung
ProLights
ProLights DIAMOND19WH Bedienungsanleitung
ProLights
ProLights DC2064 Bedienungsanleitung
ProLights
ProLights Halurock Bedienungsanleitung
ProLights
ProLights DIAMOND19CC Bedienungsanleitung
ProLights
ProLights LUMIPIX8H Bedienungsanleitung
ProLights
ProLights FURY FY250S Bedienungsanleitung
ProLights
ProLights MOVING HEAD Bedienungsanleitung
ProLights
ProLights Krypton 40G Bedienungsanleitung
ProLights
ProLights ArcShine M9/18FC Bedienungsanleitung
ProLights
ProLights BEAMROLL8W Bedienungsanleitung
ProLights
ProLights Fury FY400S Bedienungsanleitung
ProLights
ProLights HZ900D Bedienungsanleitung
ProLights
ProLights PINSPOT 101 Bedienungsanleitung
Beliebte Beleuchtungsausrüstung Handbücher anderer Marken
Qazqa
Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung
Commercial Electric
Commercial Electric 54568141 Bedienungsanleitung
CREE LIGHTING
CREE LIGHTING 304 Series Bedienungsanleitung
Goobay
Goobay 49867 Bedienungsanleitung
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Bedienungsanleitung
Alkalite
Alkalite Krypton KT-81 Bedienungsanleitung
