Promotech LIZARD Bedienungsanleitung

ul. Elewatorska 23/1, 15-620 Białystok, Poland

Phone: +48 85 678-34-00, Fax: +48 85 651-15-31

www.promotech.eu e-mail: office@promotech.eu

OPERATOR’S MANUAL

WELDING CARRIAGE

Contents

1. GENERAL INFORMATION............................................................................................... 3

1.1. Application................................................................................................................. 3

1.2. Technical data............................................................................................................ 3

1.3. Design ....................................................................................................................... 5

1.4. Equipment included ................................................................................................... 6

2. SAFETY PRECAUTIONS.................................................................................................. 7

3. STARTUP AND OPERATION........................................................................................... 9

3.1. Preparing................................................................................................................... 9

3.2. Connecting to welding circuits...................................................................................10

3.3. Positioning at the worksite ........................................................................................11

3.4. Starting .....................................................................................................................12

3.5. Programming ............................................................................................................12

3.6. Welding procedure....................................................................................................14

3.7. Operating..................................................................................................................15

3.8. Using oscillator (accessory) ......................................................................................16

3.8.1. Installing..........................................................................................................16

3.8.2. Welding with oscillation...................................................................................17

3.8.3. Operating........................................................................................................18

3.9. Troubleshooting........................................................................................................19

4. MAINTENANCE...............................................................................................................20

5. ACCESSORIES...............................................................................................................21

5.1. Oscillator...................................................................................................................21

5.2. 16–22 mm torch clamp..............................................................................................23

5.3. 16–22 mm torch clip..................................................................................................23

5.4. 22–35 mm torch clamp..............................................................................................23

5.5. Short rod...................................................................................................................24

5.6. Long rod....................................................................................................................24

5.7. Short rod torch holder with clamp..............................................................................24

5.8. Short rod torch holder with clip..................................................................................25

5.9. Short rod low torch holder with clip............................................................................25

5.10. Long rod torch holder with clamp ............................................................................25

5.11. Long rod torch holder with clip.................................................................................26

5.12. Torch extension arm ...............................................................................................26

5.13. Edge following guide arms......................................................................................27

5.14. Adjustable guide arms.............................................................................................28

5.15. Magnet guide arms .................................................................................................29

5.16. Dual torch mount.....................................................................................................32

5.17. Guiding set..............................................................................................................33

5.18. Guide adjustment tool .............................................................................................35

5.19. 76 mm cross slide...................................................................................................36

6. WIRING DIAGRAM..........................................................................................................37

7. DECLARATION OF CONFORMITY.................................................................................38

8. QUALITY CERTIFICATE..................................................................................................39

9. WARRANTY CARD..........................................................................................................40

LIZARD

This document is protected by copyrights.

Copying, using, or distributing without permission of PROMOTECH is prohibited.

1. GENERAL INFORMATION

1.1. Application

The LIZARD is a welding carriage designed to produce continuous or intermittent butt

and fillet welds using MIG/MAG torches with the handle diameter of 16–22 mm (0.63–

0.87’’). The carriage is fixed by permanent magnets and can work in the following

welding positions: PA/1F/1G, PB/2F, PC/2G, PD/4F, and PE/4G.

Accessories allow, for instance, welding with oscillation, using torches with the

handle diameter larger than 22 mm, two torches simultaneously, guiding the carriage

along outside edges, lap joints and templates, walls low or with holes, and on ceilings,

pipes, and tanks.

1.2. Technical data

Voltage

1~ 115–230 V, 50–60 Hz

Power

25 W

Welding position (according to

EN ISO 6947 and AWS/ASME)

horizontal

PA / 1F / 1G

PB / 2F

PC / 2G

PD / 4F

PE / 4G

vertical

PF / 3F / 3G (with optional oscillator)

PG / 3F / 3G (with optional oscillator)

Minimum path curvature radius

1500 mm (5 ft)

Torch type

MIG/MAG

Torch diameter

16–22 mm (0.63–0.87’’)

Maximum torch reach

80 mm (3.15’’)

Maximum permitted cable weight

horizontal work

12 kg (27 lbs)

vertical work

8 kg (18 lbs)

Minimum workpiece thickness

5 mm (0.20’’)

Ground clearance

5 mm (0.20’’)

Horizontal pulling force

220 N

Vertical pulling force

150 N

Cross slide adjustment range

0–35 mm (0–1.38’’, up-down, left-right)

Guide arm adjustment range

0–75 mm (2.95’’)

Horizontal speed

0–120 cm/min (0–47.2 in/min)

Vertical speed

0–110 cm/min (0–43.3 in/min)

Noise level

Less than 70 dB

Weight

14 kg (31 lbs)

LIZARD

This document is protected by copyrights.

Copying, using, or distributing without permission of PROMOTECH is prohibited.

411 mm (16.2’’)

368 mm (14.5’’)

447 mm (17.6’’)

LIZARD

This document is protected by copyrights.

Copying, using, or distributing without permission of PROMOTECH is prohibited.

1.3. Design

The LIZARD welding carriage consists of a chassis, a drive system, a controller,

a cross slide, two guide arms, a cable anchor, and a torch holder. The drive system

contains a gear-motor that drives four rubber wheels.

Permanent magnets fitted at the carriage bottom ensure proper clamping to

ferromagnetic surfaces. The cross slide allows for precise control of the torch holder

position in both the horizontal and vertical axis, and connecting the arc ignition cable

will enable the carriage to ignite an arc when selecting a travel direction.

Fig. 1. View of the LIZARD

Safety line lug

Arc ignition socket

Control panel

Cable anchor

Cross slide

Oscillation socket

Guide arm

Torch holder

Power switch

Limit switch

Magnet ON/OFF lever

LIZARD

This document is protected by copyrights.

Copying, using, or distributing without permission of PROMOTECH is prohibited.

Fig. 2. View of the control panel

1.4. Equipment included

The LIZARD is supplied including the following elements.

Carriage

1 unit

Foam filled cardboard box

1 unit

Cable anchor

1 unit

Short rod torch holder with clamp

1 unit

3 m (10 ft) power cord

1 unit

6.5 m (21 ft) arc ignition cable

1 unit

4 mm hex wrench

1 unit

Operator’s Manual

1 unit

LCD display

Knob F1

Knob F2

Arc ignition switch

(TEST / O / I)

Travel direction switch

(Left / O / Right)

Speed adjustment knob

LIZARD

This document is protected by copyrights.

Copying, using, or distributing without permission of PROMOTECH is prohibited.

2. SAFETY PRECAUTIONS

1. Before beginning, read this Operator’s Manual and complete proper occupational

safety and health training.

2. Use the carriage only in applications specified in this Operator’s Manual.

3. The carriage must be complete and all parts must be genuine and fully operational.

4. The specifications of the power source must conform to those specified on the

ratingplate.

5. Plug the carriage into a properly grounded power source.

6. Never carry the carriage by the cords or the arc ignition cable and never pull them

as this may damage them and result in electric shock.

7. Untrained bystanders must not be present near the carriage.

8. Before beginning, make sure that the correct is the condition of the carriage, power

source, cords, arc ignition cable, plugs, control panel, and wheels.

9. Keep the carriage dry. Exposure to rain, snow, or frost is prohibited.

10. Keep the work area well lit, clean, and free of obstacles.

11. Never use near flammable liquids or gases, or in explosive environments.

12. Make sure that the rubber of the wheels is clean and not damaged.

13. Never disassemble the cover of the wheels.

14. Remove objects attracted to the chassis by the magnet.

15. Transport and position the carriage using the carrying handle and only when the

magnet ON/OFF lever is set to the position ‘O’.

16. Position the carriage on the ferromagnetic workpiece in such a way that the

wheels are in contact with the surface and there is no contact between the

surface and the chassis.

17. Do not stay below the carriage placed at heights.

18. Plug the cords and the arc ignition cable only when the power switch is set to the

position ‘O’.

19. Keep the sockets clean. Do not use compressed air for cleaning.

20. Install only MIG/MAG torches with the handle diameter corresponding to the

torch holder in use.

21. Position the torch not more than 80 mm (3.15’’) outward from the left or right side

of the carriage.

LIZARD

This document is protected by copyrights.

Copying, using, or distributing without permission of PROMOTECH is prohibited.

22. Keep the torch cables from coming in contact with the surface. They must be

suspended to reduce the load of the carriage. Use only cables whose weight is

not more than 12 kg (27 lbs) for horizontal work and 8 kg (18 lbs) for vertical work.

23. Operating on curvatures with a convex or concave radius less than 1500 mm (5 ft)

is prohibited.

24. When operating at heights, use a safety line to protect the carriage from dropping.

25. Always use eye protection (helmet, shield, and screen), hearing protection, gloves,

and protective clothing during operation. Do not wear loose clothing.

26. Before every use, inspect the carriage to ensure it is not damaged. Check whether

any part is cracked or improperly fitted. Make sure to maintain proper conditions

that may affect the operation of the carriage.

27. Never try to manually stop the motion of the carriage. To stop, set the travel

direction switch to the position ‘O’.

28. Maintain only when the carriage is unplugged from the power source.

29. Repair only in a service center appointed by the seller.

30. If the carriage falls from any height, is wet, or has any other damage that could

affect the technical state of the carriage, stop the operation and immediately

send the carriage to the service center for inspection and repair.

31. Never leave the carriage unattended during operation.

32. Remove from the worksite and store in a secure and dry location when not in use.

LIZARD

This document is protected by copyrights.

Copying, using, or distributing without permission of PROMOTECH is prohibited.

3. STARTUP AND OPERATION

3.1. Preparing

Use the carrying handle to transport the carriage to the worksite. Then, set to the

position ‘O’ all the switches (power, travel direction, and arc ignition switch) and the

magnet lever.

Fig. 3. View from the back side

Connect the carriage to the power source, insert the torch into the torch holder,

and then secure it with the knob. Next, insert the torch cable into the cable anchor,

secure it with the knobs, and then fix the anchor in the required position using

the lever.

Knob securing the torch in the holder

Precise torch position

adjustment knobs

Knobs securing the cable in the anchor

Lever securing

the cable anchor

Levers securing the torch

position and angle

Screws securing the guide arm

Carrying handle

LIZARD

This document is protected by copyrights.

Copying, using, or distributing without permission of PROMOTECH is prohibited.

3.2. Connecting to welding circuits

The carriage can control two torches using the arc ignition cable plugged into the arc

ignition socket. To do this, connect any blue-jacketed wire to any terminal of the welding

circuit, and then connect the second blue-jacketed wire to the second terminal of the

same circuit, according to the diagram shown in Fig. 4. To control the second torch,

connect the green-jacketed wires to the terminals of the second welding circuit.

Fig. 4. Connecting the arc ignition cable to welding circuits

To check whether the arc ignition cable is connected correctly, power the carriage

by setting the power switch to the position ‘I’, and set the arc ignition switch to the

position TEST, which should enable the arc for a while.

blue

Welding circuit 1

green

Welding circuit 2

Inhaltsverzeichnis

Andere Promotech Schweißsystem Handbücher

Promotech

Promotech Mini Spider Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

Lincoln Electric

Lincoln Electric HANDYMIG 170I Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

ESAB

ESAB Buddy Arc 145 Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

WIA

WIA Weldmatic 270 CP132-2 Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung