PROPOINT 9011495 Bedienungsanleitung

V1.0 9011495

Please read and understand all instructions before use. Retain this manual for future reference.

9011495 Pen-Probe-Style Autoranging Digital Multimeter V1.0

2 For technical questions call 1-800-665-8685

Display 3-1/2 digit LCD with a maximum reading of 1,999

Polarity Auto polarity indication

Over-range Indication "OL" shown on the display

Sampling Rate 3 times per second

Power Single standard 9V battery

Low Battery Indication is displayed when the battery voltage drops

below the operating voltage

Auto Power Off If the meter is not operated for about 15 minutes, it

will turn off automatically and stay in Sleep mode.

Operating Temperature

0°C to 40°C, < 75%RH

Storage Temperature -20°C to 60°C, < 85%RH

Accessories 9V battery, owner's manual

FUNCTION

RANGE RESOLUTION

DC Voltage 200mV ± (0.5% + 2)

2V - 20V - 200V ± (0.7% + 2)

300V ± (0.8% + 2)

Input impedance: about 10M

Max. permitted input voltage: 300V DC

AC Voltage 2V ± (0.8% + 3)

20V - 200V ± (1.2% + 3)

300V ± (1.5% + 3)

Input impedance: about 10M

Frequency: 40Hz - 400Hz

Max. permitted input voltage: 300V AC

V1.0 Pen-Probe-Style Autoranging Digital Multimeter 9011495

Visit www.princessauto.com for more information 3

DC Current 20mA ± (1.2% + 3)

200mA

Max. permitted input current: 200mA DC, overcurrent will

blow the fuse

AC Current 20mA ± (1.5% + 5)

200mA

Frequency: 40Hz - 400Hz

Max. permitted input current: 200mA AC, overcurrent will

blow the fuse

Resistance 200 ± (1.2% + 3)

2k , 20k , 200k , 2M ± (1.0% + 2)

20M ± (2.0% + 2)

Diode test Open circuit voltage: approximately 1.5V

Test current: approximately 0.5mA

Audible

continuity Built-in buzzer sounds if resistance is less than 50 .

Built-in buzzer might sound if resistance is between 50 and

120 .

Built-in buzzer does not sound if resistance is greater

than 120 .

Please familiarize yourself with the hazard notices found in this manual.

A notice is an alert that there is a possibility of property damage, injury

or death if certain instructions are not followed.

DANGER! This notice indicates an immediate and specific hazard that

will result in severe personal injury or death if the proper

precautions are not taken.

WARNING! This notice indicates a specific hazard or unsafe practice

that could result in severe personal injury or death if the

proper precautions are not taken.

CAUTION! This notice indicates a potentially hazardous situation that

may result in minor or moderate injury if proper practices are

not taken.

9011495 Pen-Probe-Style Autoranging Digital Multimeter V1.0

4 For technical questions call 1-800-665-8685

NOTICE! This notice indicates that a specific hazard or unsafe

practice will result in equipment or property damage, but

not personal injury.

This compact digital multimeter is used for measuring DC and AC

voltage, DC and AC current, resistance, diode, continuity, and logic level.

This meter was designed for the homeowner, hobbyist, and professional

needing to make electrical and electronic equipment measurements.

WARNING! Read and understand all instructions before using this

tool. Keep this manual for the safety warnings and precautions,

operating, inspection and maintenance instructions. When using

this tool, basic precautions should always be followed to reduce

the risk of personal injury and/or damage to the equipment. Note

that when this manual refers to a part number, it refers to the

parts list included. Before allowing someone else to use this tool,

make sure they are aware of all safety information.

1. Keep your work area clean and well lit. Cluttered and dark areas

invite accidents.

2. Operate in a safe work environment. Do not use machines or air

tools in damp or wet locations. Do not expose to rain.

3. Keep children, bystanders and visitors away from the work area. Do

not let them handle tools or extension cords. No one should be in

the work area if they are not wearing suitable protective equipment.

4. Store unused equipment. When not in use, tools must be stored in

a dry location to prevent rust. Always lock up tools and keep them

out of reach of children.

1. Dress properly, wear protective equipment.

2. Do not over reach; keep proper footing and balance at all times.

Proper footing and balance enables better control of the tool in

unexpected situations.

V1.0 Pen-Probe-Style Autoranging Digital Multimeter 9011495

Visit www.princessauto.com for more information 5

3. Stay alert, watch what you are doing and use your common sense.

Do not operate any machine or tool when you are tired, under the

influence of drugs, alcohol or medications.

This meter has been designed according to IEC-61010 concerning

electronic measuring instruments with a measurement category III (CAT

III 300V) and pollution degree 2. Measuring Category III (CAT III) is for

measurement performed on circuits directly connected to low voltage

installation (for example, measurements on household appliances,

portable tools, and similar equipment). Do not use this meter for

measurements within Measurement Category IV.

WARNING! To avoid possible electric shock or personal injury,

follow these guidelines:

1. Ensure that the batteries are correctly placed in the battery case

and connected properly.

2. Do not operate the meter with the battery cover or portions of the

case removed or loosened.

3. Do not use the meter if it is damaged. Before you use the meter,

inspect the case. Inspect the test leads for damaged insulation or

exposed metal. Check test lead continuity. Damaged leads should

be replaced.

4. Do not use the meter if it operates abnormally. Protection may be

impaired. When in doubt, have the meter serviced an authorized

service center.

5. Do not operate the meter around explosive gas, vapor, or dust.

6. Do not apply a voltage or current higher that the selected range’s

upper limit between terminals.

7. Before use, verify the meter’s operation by measuring a known voltage.

8. When measuring current, turn off power to the circuit before

connecting the meter to the circuit. Remember to place the meter

in series with the circuit.

9. Use caution when working above 30V AC rms, 42V peak, or 60V

DC. Such voltages pose a shock hazard.

9011495 Pen-Probe-Style Autoranging Digital Multimeter V1.0

6 For technical questions call 1-800-665-8685

10. Do not touch any naked conductor with hand or skin and do not

ground yourself.

11. Connect the black test lead before connecting the red test lead. When

disconnecting test leads, always disconnect the red test lead first.

12. Remove the test leads from the meter before opening the battery

cover or the case.

13. Replace the battery as soon as the low battery indicator appears

on the LCD display.

CAUTION! To avoid possible damage to the meter or to the

equipment under test, follow these guidelines:

1. Disconnect circuit power and discharge all capacitors before

measuring resistance or continuity.

2. Select the proper function and range for your measurement.

3. Before measuring current, turn off the power to the circuit before

connecting the meter to the circuit.

4. Before rotating the range switch to change functions, disconnect

the test leads from the circuit under test.

5. Remove the test leads from the meter before opening the battery

cover or the case.

6. When finished measuring, switch off the power. Be sure to remove

the batteries when storing for long periods to avoid leakage

problems.

7. Do not use or store this instrument in a place of direct sunlight,

high temperature and high humidity.

1. Carefully remove the parts and accessories from the box.

2. Make sure that all items listed in the parts lists are included.

3. Inspect the parts carefully to make sure the tool was not damaged

while shipping.

4. Do not discard the packaging material until you have carefully

inspected and satisfactorily operated the tool.

V1.0 Pen-Probe-Style Autoranging Digital Multimeter 9011495

Visit www.princessauto.com for more information 7

WARNING! If any part is missing, do not operate the tool until the

missing parts are replaced. Failure to do so could result in

serious personal injury.

1. Display

2. Button

To enable the

flashlight function,

press and hold down

this button. To turn off

the flashlight, release

the button.

3. Button

To hold the present

reading on the display,

press this button. will appear on the display as an indicator. To

exit the hold mode, press this button again. will no longer appear

on the display. This button can also be used to wake the meter

from sleep mode.

4. Function Switch

Used to select the required function or range, as well as turn off the

meter. To preserve battery life, set this switch to the “OFF” position

when the meter is not is use.

5. Test Probe

Input probe (positive polarity) for the following tests: voltage,

current (< 200mA), resistance, and diode.

6. Flashlight LED

Used for illumination.

9011495 Pen-Probe-Style Autoranging Digital Multimeter V1.0

8 For technical questions call 1-800-665-8685

7. Button

Used to switch the meter between:

• DC voltage and AC voltage measurements

• DC current and AC current measurements

• Diode and continuity tests

8. Button

To turn on or off the backlight, press and hold down this button for

about 1 second. The backlight will turn off automatically about 15

seconds after being turned on.

9. Probe of the Black Test Lead (Negative Polarity)

10. Black Test Lead

1. Set the function switch to the position.

2. Press the button to select DC voltage measurement.

Appears on the display.

3. Connect the test probe and the black test lead across the source

or circuit to be measured.

4. The display shows the reading and the polarity of the test probe

connection.

1. Set the function switch to the position.

2. Press the button to select AC voltage measurement.

Appears on the display.

3. Connect the test probe and the black test lead across the source

or circuit to be measured.

4. The display shows the reading.

1. Set the function switch to the position.

2. Press the button to select DC current measurement.

Appears on the display.

V1.0 Pen-Probe-Style Autoranging Digital Multimeter 9011495

Visit www.princessauto.com for more information 9

3. Connect the test probe and the black test lead in series with the

circuit to be measured.

4. The display shows the reading and the polarity of the test

probe connection.

1. Set the function switch to the position.

2. Press the button to select AC voltage measurement.

Appears on the display.

3. Connect the test probe and the black test lead in series with the

circuit to be measured.

4. The display shows the reading.

1. Make sure the load to be tested is without power and all capacitors

are fully discharged.

2. Set the function switch to the position.

3. Connect the test probe and the black test lead across the load to

be measured.

4. The display shows the reading.

IMPORTANT! If the resistance is more than 1M, it may take

several seconds to stabilize the reading. This is normal for high

resistance measurements.

IMPORTANT! If the probes are open, overload indication will be

shown on the display.

1. Set the function switch to the position.

2. Press the button until appears on the display.

3. Connect the test probe to the anode of the diode and the black test

lead to the cathode of the diode being measured.

4. Read the approximate forward voltage drop of the diode on

the display.

9011495 Pen-Probe-Style Autoranging Digital Multimeter V1.0

10 For technical questions call 1-800-665-8685

1. Turn off the power to the circuit under test, and then discharge all

capacitors and inductors.

2. Set the function switch to the position.

3. Press the button until appears on the display.

4. Connect the test probe and the black test lead across the circuit

being measured.

5. If the resistance of the circuit is less than 50 , the built-in buzzer

will sound.

1. Set the function switch to the position.

2. Connect the black test lead to the ground terminal of the circuit to

be measured and the test probe to the required test point of

the circuit.

3. If the level of the test point is more than or equal to 2.3 ± 0.2V, the

display will show “HI ” and the voltage value. The meter will sound

discontinuously.

4. If the level of the test point is less than or equal to 0.8 ± 0.2V, the

display will show “LO ” and the voltage value. The meter will

sound continuously.

5. If the probes are open, the display will show a TTL logic levels

approximate mid value (1.0 to 1.4V).

CAUTION! Before attempting to open the case of the instrument,

be sure to disconnect the test lead and the test probe from any

energized circuits to avoid shock hazard.

When appears on the display, the battery is low and should be

replaced immediately. To replace the battery, follow these steps:

1. Remove the screws from the battery cover, and then remove the

battery cover.

2. Replace the old battery with new battery of the same type (9V).

3. Reinstall the battery cover and the screws.

Inhaltsverzeichnis

Sprachen:

Andere PROPOINT Multimeter Handbücher

PROPOINT

PROPOINT 8344749 Bedienungsanleitung

Beliebte Multimeter Handbücher anderer Marken

Agilent Technologies

Agilent Technologies 34420A Bedienungsanleitung

Fluke

Fluke 83 Bedienungsanleitung

Hameg

Hameg HM 8012 Bedienungsanleitung

Mastech

Mastech MY70 Bedienungsanleitung

Steren

Steren MUL-300 Bedienungsanleitung

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Bedienungsanleitung

PeakTech

PeakTech 4000 Gebrauchs- und Pflegehandbuch

YOKOGAWA

YOKOGAWA 90050B Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Bedienungsanleitung

Fluke

Fluke 8846A Bedienungs- und Wartungshandbuch

Tempo Communications

Tempo Communications MM200 Bedienungsanleitung

Elenco Electronics

Elenco Electronics CM-1555 Bedienungsanleitung

Mastech

Mastech MS8238C Bedienungsanleitung

SDAR

SDAR 830A, 830B, 830D, 830C Bedienungsanleitung

RS PRO

RS PRO RS-9519BT Bedienungsanleitung

BGS technic

BGS technic 8890 Bedienungsanleitung

Amprobe

Amprobe Hexagon 60 Bedienungsanleitung