Protected Home WA-5000 Bedienungsanleitung

WaterAlarm Plus

Model WA-5000

Thank you for purchasing the WaterAlarm Plus. We are confident this product

will provide you with the peace of mind and protection you expect. If you

should ever have any questions or concerns about this product, feel free to

back of this instruction manual.

GENERAL DESCRIPTION

The WaterAlarm Plus is designed to alert you by telephone if water is detected

by the water sensor. The product consists of two components connected

together by six feet (1.8m) of wire.

1) The Dialer – This component connects to your existing telephone line to

make continuous phone calls every 15 minutes (or 2 hours) if water is detected.

When the WaterAlarm calls you, the person answering the call will hear a pre-

recorded water alarm message.

2) The Water Sensor – This component is what detects the water and sounds an

85 decibel alarm. The sensor can sit directly on the ground, or the sensor can be

detached and extended up to six feet from the audible alarm part with the

included sensor wire. You can add additional wired water sensors to cover

multiple locations within a home, cabin or business.

FEATURES

•Automatically dials to one telephone number when water is detected by the

wired water sensor. The WaterAlarm can call any telephone number

including a cell phone, calling card number, or international number.

•Plays a pre-recorded voice alarm message in English. The message is “This

is your water alarm. Water has been detected at your monitored location.

Please check conditions at your monitored location.” The WaterAlarm will

repeat the message for one minute, allowing it to be recorded on an

answering machine or voice mail if desired.

•Continues to call your programmed telephone number until the alarm call

out is canceled by calling back to the WaterAlarm from any phone in the

world.

•Enter and change the “call-to” telephone number easily. Special memory

keeps the phone number stored forever even if the battery goes dead or is

removed.

•Call-to telephone number can be up to 40 digits long including the “*” key

if required.

•Dialing indicator light

•Option to add additional wired sensors (part number WA-20)

•Operates on Touch Tone™ telephone lines only.

•FCC Approved

TABLE OF CONTENTS:

General Description & Features.....................................................................1

Installation & Programming..........................................................................2

Initial Setup ...........................................................................................3

Programming or Changing the “Call-To” phone number.........................4

Positioning the Water Sensor..................................................................6

Extending the Wires of the Various Components....................................6

Testing your WaterAlarm..............................................................................6

Operation

During an alarm.....................................................................................7

Canceling the Alarm Call-Out ................................................................7

Resetting your WaterAlarm....................................................................8

Checking Alarm Condition at Monitored Location..................................8

Use with Answering Machines and Voice Mail.......................................8

Troubleshooting............................................................................................9

Commonly Asked Questions.......................................................................10

Contacting for Sales or Technical Support...................................................11

Specifications .............................................................................................12

FCC Statement............................................................................................12

Warranty Statement.....................................................................................13

INSTALLATION & PROGRAMMING

IMPORTANT!

•Read the warranty information on page 13 and the FCC statement on

page 12 before using this product.

•The performance of local and long distance telephone lines vary from

location to location and may affect operation of the WaterAlarm.

Therefore, it is important that the WaterAlarm be fully tested after

installation to confirm telephone compatibility. Please see the Testing

your WaterAlarm on page 6 for further instructions.

•Caution - To ensure proper operation, this equipment must be installed

according to the enclosed installation instructions. To verify that the

equipment is operating properly and can successfully report an alarm,

this equipment must be tested immediately after installation, and

periodically thereafter, according to the enclosed test instructions.

•Caution – This equipment cannot report an alarm when other

equipment (telephone, answering system, computer modem, etc.)

connected to the same phone line is in use.

•Important – Do not program emergency phone numbers for the police,

fire or other emergency personnel or departments unless you have

specific approval from such agencies. This model of WaterAlarm does

not identify the location that is calling and therefore cannot provide an

audible notification of what address this phone call originated from.

A. What You Will Need:

1. Two 9-volt alkaline batteries are included. The water sensor battery is

located inside the battery compartment of the water sensor. The other 9

volt battery should be included with the rest of the packaging.

2. Phillips screwdriver (not included)

3. A single line telephone jack. This does not need to be a dedicated

phone jack; a phone can share the jack with the WaterAlarm through

the use of a telephone line splitter (not included). These are available

at most hardware, electronics or discount stores. You must have

Touch-Tone® telephone service for the WaterAlarm to properly

operate. The WaterAlarm will not work on pulse or rotary dialing

telephone systems.

B. Installation:

1. On the Dialer component, remove the four screws from the back cover.

2. Install the 9-volt battery in the battery compartment by attaching the

battery clips.

3. With the cover still removed, locate the four little “dip” switches on the

circuit board.

What the switches are used for:

Switch

# What it does OFF

Position ON

Position Default

Position

1 FACTORY USE ONLY – Do not

change NA NA OFF

2 Pick Up Ring Count. When you call

your monitored location, should the

WaterAlarm pick up after 5 rings or

10 rings?

10 rings 5 rings ON for 5 rings

3 Call out frequency during an alarm.

How often should the WaterAlarm

call the pre-programmed telephone

number?

Every 15

minutes Every 2

hours ON for every 2

hours

4 Normally Open or Normally Closed

Alarm Input Position. The water

sensors connected to the Dialer

require the Normally Open position.

Normally

Closed

Position

Normally

Open

Position

ON for the

Normally

Open Position

Switch Explanation:

Switch #1: Factory set to OFF. Do not change the setting of this

switch.

Switch #2: Pick Up Ring Count: This is the number of rings at which

your WaterAlarm will answer so you can cancel the alarm call out.

The default setting is to answer after five rings. If you have an

answering machine or voice mail, you want to be sure the answering

machine or voice mail answers on less rings than what you have this set

for. For more information on this feature, see the section titled

Answering Machines/Voice Mail at Monitored Location under the

OPERATION section.

Switch #3: Call out Frequency: Your WaterAlarm can call your

programmed telephone number every 15 minutes or every 2 hours. The

default setting is to call out every 2 hours during an alarm.

Switch #4: The Dialer has the capability of dialing out if the sensors

either close an alarm contact or open an alarm contact. For the

WaterAlarm, the included sensor is normally open and will close when

water is detected. Therefore, this switch must be left in the “ON”

position, or Normally Open position.

4. Replace the back cover. Be careful to ensure the cover goes on the

correct way as the telephone jack on the Dialer and the battery may not

sit correctly if replaced incorrectly.

5. Plug one end of the supplied telephone cord into the Dialer. Plug the

other end of the telephone cord into the wall jack of your single line

telephone. CAUTION: The Dialer requires a single line telephone, but

does not require this line to be dedicated for the Dialer use only. The

Dialer may not be compatible with some PBX or other multi-line

business telephone systems. Connecting the Dialer to a commercial

telephone system may cause internal damage to both systems. The

Dialer can share a wall telephone jack with a telephone. A dual plug

adapter or “splitter” (not included), is required and is available at most

hardware or electronics stores. The adapter allows both the Dialer and

the telephone to share the same wall phone jack. If you need additional

length to a telephone jack, you can add up to 1,000’ (304m) of

additional telephone wire.

6. On the WaterAlarm component, remove the battery compartment cover

on the side of the alarm and remove the battery and battery clip inside

the compartment. Snap the battery to the battery clip and put back into

the battery compartment and replace the battery compartment cover.

C. Programming or Changing the “Call-To” Telephone Number:

The Call-To telephone number is the number you want your WaterAlarm to

call if water is detected in your remotely monitored location. Once you

program the phone number, it is stored indefinitely. It will not be lost even

if you disconnect the battery and the phone line. The maximum number of

digits in the telephone number is 40. Eligible digits include any of the

number keys and the “star” (*) key. All digits and the star (*) key are part

of the 40 digit total.

You will be using the (#), (*) and number keys in the

programming and testing of your WaterAlarm.

Before programming, make sure your phone line is

connected to the WaterAlarm and the other end is plugged into your

telephone wall jack.

1. Press and hold the pound (#) key on the keypad.

2. While CONTINUING TO HOLD the (#) key, use the keypad to enter

the telephone number of the location you want the WaterAlarm to call.

Remember! Keep holding down the (#) key until the entire phone

number is entered! Enter the telephone number exactly as you would

if you were to dial that location on the telephone. In other words, enter

a “1” and/or the area code if required. Release the (#) key after

entering all the digits of the “call-to” telephone number.

3. Users can enter a five second pause in the phone number by pressing

the “star” (*) keytwice. This will count as two digits of the total phone

number. For every two star keys entered, there will be a five second

pause. If three star keys are entered in succession, the first two will be

noted as the 5 second pause and the third star key will be the actual (*)

key played as part of the phone number. If four star (*) keys are

entered, the WaterAlarm would pause the dialing sequence for 10

seconds.

4. Don’t forget to enter a “1” or your area code if required. Area codes

change regularly so make sure you remember to change your “call to”

telephone number if your area code has changed.

5. To change the programmed phone number, simply re-program a

number using the steps above. It will overwrite the previous number

programmed.

____________________________________________________________

IMPORTANT TIPS ON ENTERING CALL-TO PHONE NUMBER

•LONG DISTANCE: Make sure you enter the phone number exactly

like you would if you were to pick up the phone and call that person. Use

a “1” and/or the proper area code if required.

•AREA CODES: Don’t forget to change your “call-to” telephone number

if the area code changes. Your WaterAlarm will continue to call-out to

an incorrect phone number and you may incur a great deal of long

distance charges if you do not change area codes appropriately.

•DIALING “9”: Some phone systems require that you dial a “9” before

the rest of the telephone number in order to get an outside line. Simply

include the “9” at the beginning of the phone number. You may need to

add a pause after the “9” so the WaterAlarm can wait for a dial tone.

•Do not program phone numbers of emergency fire, police or ambulance

services into the WaterAlarm. There is no audible notification of the

location that is calling so the agency will not be able to identify the

address of the problem.

•TEST YOUR WATERALARM: It is critical that you test your “call-

to” number as indicated in the section, “Testing your WaterAlarm” on

page 6.

D. Positioning the Water Sensor:

The Water Sensor can be placed directly on the floor or the sensor can be

detached from the Water Alarm component via the 6’ wire and placed in a

sump hole or in another location. Hardware that is included with the

WaterAlarm allows the sensor to be mounted on a wall if desired so the

alarm can be more easily heard and then placing the water sensor in the

desired location. If a longer length is required, you can splice in additional

two conductor wire (28 AWG or larger) up to 1,000’ (304m) from the alarm

portion of the sensor.

E. Extending the Wires of the Components: The diagram to the left

shows how long each

wire can be extended. If

going through walls or

near electrical appliances

or conduit, it is

recommended you use

shielded wire. In some

cases, the WaterAlarm

may not work properly or

you may receive false

alarms at any length of

wire extension. In such

situations, look for

alternate wire routes or

shorten the length of wire

until the WaterAlarm works properly. To extend the telephone wire,

purchase telephone wire and telephone wire couplers to make get the

desired length.

TESTING YOUR WATERALARM

There are two tests you can perform to ensure your WaterAlarm is operating

properly. It is important that a person be at the “call-to” location to receive the

test call from the WaterAlarm. Both tests assume the WaterAlarm has batteries

installed, the phone line is connected and a “call-to” phone number has been

programmed per the instructions.

A. Testing if the phone number was programmed correctly. Press the star

(*) key once until you see the red indicator light up and then release the star

key. The WaterAlarm will call this number and play our pre-recoded water

alarm message for 1 minute to either the person or answering machine at the

call-to location and then hang up. You do not need to cancel the alarm call

out for this test procedure as this function should only call the programmed

number once and then complete the test.

B. Testing Alarm Call-Out if Water Is Detected. Moisten a paper towel and

place it over both of the small metal pads on the water sensor until you hear

the audible alarm go off. If the audible alarm fails to sound, your battery

may be old or dead, the paper towel may not be moist enough or the water

sensor may be damaged.

If you do hear the audible alarm, within 10 seconds, the red light on the

Dialer should light up indicating it is making a phone call. When you test

the WaterAlarm in this fashion, you do need to call back to the monitored

location and cancel the alarm call-out via the procedure outlined in the

Operation section below.

C. If either test fails. If either test fails, try reprogramming the phone number

and repeat the test(s). Check to see the wire between the water sensor and

the dialer is not damaged or disconnected. If it continues to not operate

properly, refer to the Troubleshooting section on page 9.

OPERATION

A. During an Alarm:

If water is detected by the sensor at the monitored location, the water sensor

will sound an audible alarm and your WaterAlarm will begin to call out to

the telephone number you programmed and play the WaterAlarm’s pre-

programmed alarm message. The WaterAlarm will call your programmed

phone number every 15 minutes or every 2 hours, depending upon the

position of switch #3 (see Installation in Step A). The WaterAlarm will

continue to call until the alarm call out is canceled.

The message the receiving party will hear is: “This is your water alarm.

Water has been detected at your monitored location. Please check

conditions at your monitored location.”

B. Canceling the Alarm Call out:

1. After you have received an alarm call, call the monitored location

where the WaterAlarm is located and let the phone ring 5 or 10 times

(the number of rings is determined by the position of switch #2 for the

“Call-In Ring Count”). After 5 or 10 rings, the WaterAlarm will

automatically answer and begin playing the pre-recorded water alarm

message that you heard when it called you with an alarm. Bysimply

calling your WaterAlarm and listening to the alarm message, you have

successfully canceled the alarm call out. You will not receive any more

calls for this particular water alarm emergency. If water continues to

be detected by the water sensor, the WaterAlarm unit will remain in

“alarm” mode, but it will not continue to call if the alarm call-out has

been canceled.

2. If the water around the sensor recedes and the sensor no longer detects

water, the Dialer will continue to call you to let you know there was a

water problem recently.

C. Resetting Your WaterAlarm:

The WaterAlarm automatically resets to normal monitoring mode as soon

as the water has receded away from the sensor (or sensor is pulled out of the

water) and the alarm call-out has been canceled.

Note: It is possible for ANYONE to accidentally cancel the alarm call-out

simplyby calling your monitored location while the WaterAlarm is in an

alarm condition. To help avoid this, you should either set the incoming ring

count selection to 10 rings (see Installation section) or have an answering

machine or voice mail take incoming calls first making it difficult for any

person to accidentally cancel the alarm call-out.

D. Checking Alarm Conditions at the Monitored Location:

The WaterAlarm provides a simple method of determining if a water

emergency exists at your monitored location. If the WaterAlarm has

detected water and is in alarm mode, and you have cancelled the alarm call-

out, you can call your FreezeAlarm and after 8 rings, the WaterAlarm will

answer and play the alarm message. If you call and the WaterAlarm does

not answer after 8 rings, this means the water has receded and the

WaterAlarm has reset. This only works if the alarm call-out was cancelled

prior to this call.

E. Answering Machines/Voice Mail at Monitored Location:

If you have an answering machine or voice mail at the monitored location

where your WaterAlarm is located, there is an easy way for you to still

utilize your answering machine or voice mail and access the WaterAlarm

during an alarm condition to cancel the alarm call out.

The WaterAlarm has a built-in feature whereas the unit can count incoming

rings over multiple calls to the WaterAlarm. This allows most incoming

calls to go to the user’s answering machine or voice mail service prior to the

WaterAlarm answering. All calls to the unit must be made within a 3

minute time period that starts from the moment the WaterAlarm hears the

first ring.

How This Works (an example):

1. Your WaterAlarm was set up in the Installation Section to answer on

either five (5) or ten (10) rings. You need to set up your answering

machine or voice mail to answer on a number of rings less than what

your WaterAlarm is set to answer at. For example, if your WaterAlarm

is set to answer on 5 rings, set your answering system to answer on four

rings or less.

2. When your monitored location receives an incoming call, it will go to

the answering system first because that is set to answer on four or less

rings while your WaterAlarm is set to answer on five rings.

3. If you wish to call your WaterAlarm to either check the alarm condition

or to cancel the alarm call out, you will need to place two calls to your

monitored location.

a. On the first call, let the phone ring two or three times and then

hang up before your answering system answers. The

WaterAlarm will remember those first two or three rings in

memory for the next three minutes.

b. On your second call, let the phone ring another two or three

times. Your WaterAlarm will answer first because it

remembered the first two or three rings and with the second

set of rings, it accumulated a total of five rings and now

answers before your answering machine or voice mail. If you

have your WaterAlarm set to answer on ten rings, you may

need to place more calls to get the WaterAlarm to eventually

answer.

4. Note that with every call to your monitored location, the three minute

timer resets. This means that if your monitored location receives a

number of calls in quick succession, it is possible for any person to

accidentally cancel the alarm call out. If you know your location will

receive a large number of calls regularly, you may wish to set your

incoming ring count on your WaterAlarm to 10 rings.

F. Answering Machines & Voice Mail at the Call-To Location:

If you have an answering machine or voice mail message system at the call-

to location, the alarm message can be recorded by such systems. This will

not cancel the alarm call-out and the WaterAlarm will continue to leave

messages until the alarm call-out is canceled. Some answering machines

and voice mail systems, however, are not compatible with our alarm

message and for some reason do not allow the message to be recorded.

TROUBLESHOOTING

1. Your WaterAlarm does not call out during a test call out or during an

alarm call-out.

Check to make sure the battery is installed properly or if the battery is low

on power. Check if phone service is working properly. Check phone cord

connections. Re-program making sure the telephone cord is connected to

the wall-jack. Also, note if you programmed the correct phone number

using the appropriate area codes or “1” for long distance. If you are using a

phone calling card, check to see that the calling sequence includes pauses as

may be required. Check to see that the switches are properly set on

WaterAlarm. Make sure you are using the WaterAlarm on only a single

phone line. The WaterAlarm may not operate on a PBX or digital phone

line or phone system. You can verify this by plugging a standard, single

line telephone into the wall jack and picking up the handset. If you get a

dial tone, your WaterAlarm should work as well. If you don’t get a dial

tone, your WaterAlarm may not work on that telephone jack or there may

be a problem with your phone service.

2. Cannot cancel the alarm call out.

Verify you have dialed the correct number of the monitored location. There

could also be trouble with the phone service in the area that is not allowing

your phone call to go through to the monitored location. Check with your

phone company if you suspect this problem.

3. Receiving False Alarms

The WaterAlarm’s water sensor requires that water must make contact

across the two little metal pads on the bottom of the sensor. It is possible a

damp floor during periods of high humidity could cause the sensor to false

alarm. If this is not the case, then check the wire to the sensor. If it is worn

in any place that could cause it to short, this would also cause a false alarm.

The audible alarm would also go off as well if this were the case. The third

problem could be in the wire between the Dialer and the Water Sensor. If

this wire has become worn or shorted out, the Dialer would see that as a

“closed” alarm condition and begin to call out, even though no water is

present. Check this wire or replace if you suspect this is the cause of the

problem.

4. The alarm call-out has been canceled, but the WaterAlarm continues to

call.

It is possible the water temporarily receded causing the water alarm to reset,

but then water returned and the unit went back into alarm mode and began

to call again.

COMMONLY ASKED QUESTIONS

1. The WaterAlarm is not calling the correct “call-to” location. Why?

This may be due to entering an incorrect “call to” telephone number or

a dead battery. Check or replace the battery and double check the

“call to” telephone number. Did you enter a “1” before a long

distance phone number? Check to see if your area code has changed

and re-program the “call to” number with the correct area code.

2. If I unplug the WaterAlarm or take out the battery, will Ihave to re-enter

the “call-to” telephone number?

Once your WaterAlarm is programmed, the “call-to” number will be

retained in memory indefinitely whether the WaterAlarm is plugged in

or not or if the battery goes dead or is taken out. You can always

program a new “call-to” telephone number at any time.

3. Do I need a dedicated telephone line for my WaterAlarm?

No. The WaterAlarm uses any existing single line telephone line. In

some cases, if you have two phone lines coming into a home, the

WaterAlarm may work on any of those telephone jacks as well. The

WaterAlarm can also share a telephone line with a telephone, modem

or fax machine, provided you purchase a dual plug adapter or a line

splitter. Those are available at most stores or directly from Control

Products.

4. Can I change the alarm message that is played during a water alarm?

No. The alarm message is pre-recorded at our factory and cannot be

changed.

5. Will the WaterAlarm work on multi-line business phone systems, PBX

systems or digital telephone systems?

No. The WaterAlarm is designed to work only with a single telephone

line, found in most residential homes. Sharing a phone line with a

telephone, fax machine, or computer modem is acceptable as long as

they are sharing a single telephone line. Some PBX systems simply

require a “9” to be dialed before calling the regular call-to number.

The WaterAlarm should be able to dial the “9” and the rest of the

number. You may need to enter a pause after the 9 to wait for the dial

tone before the rest of the number is dialed by the Dialer.

CONTACTING US – SALES & TECHNICAL SUPPORT:

For Sales or Technical Support, contact Customer Service:

Protected Home, a Division of Control Products, Inc.

1724 Lake Drive West

Chanhassen, MN 55317

952-448-2217

Fax 952-361-9420

customerserevice@controlproductsinc.com

www.protectedhome.com

When calling or writing for customer support or service, it is a good idea to have the following

information readily available. Please write this information down in the space provided below for

future reference.

Model Number Information:

The actual model number of your unit can be found on the back of the WaterAlarm.

WA-5000

Additional Sensors: WA-20

DATE CODE/MO# from the back of your WaterAlarm:___________________________________

Where unit was purchased__________________________ Date of purchase:________________

Custom Design and Modifications:

Since 1985, Control Products, Inc. has been designing and manufacturing unique, exciting and

technologically advanced electronic control circuits for both commercial and consumer use. We can

modify one of our many standard products or our in-house engineering staff and state-of-the-art

manufacturing can build a project from the ground up.

Please contact our customer service department to arrange a personal visit from one of our

representatives, posted in facilities through the United States, or visit our website at

www.controlproductsinc.com.

SPECIFICATIONS

Power Requirements: Two 9-volt alkaline or lithium batteries

MAKE SURE YOU REPLACE BATTERIES ANNUALLY OR REMOVE WHEN THE

UNIT IS NOT IN USE!

Operating Ambient Temperature Range: 20° to 140°F (-7° to 60°C)

Humidity: 90% non-condensing

REN (Ring Equivalence Number): 0.1B

FCC Statement:

This equipment complies with Part 68 of the FCC rules and the requirements adopted by

the ACTA. On the back of your WaterAlarm is a label that contains, among other

information the FCC registration number for this product. Ifrequested, this number must

be provided to the telephone company.

A plug and jack used to connect this equipment to the premises wiring and telephone

network must comply with the applicable FCC Part 68 rules and requirements adopted by

the ACTA. A compliant telephone cord and modular plug is provided with this product.

It is designed to be connected to a compatible modular jack that is also compliant. See

installation instructions for details.

The REN is used to determine the number of devices that may be connected to a

telephone line. Excessive REN’s on a telephone line may result in the devices not

ringing in response to an incoming call. In most but not all areas, the sum of REN’s

should not exceed five (5.0). To be certain of the number of devices that may be

connected to a line, as determined by the total REN’s, contact your local telephone

company. The REN for this product is shown above and is also identified as part of the

FCC product identifier shown on the label on the back of your WaterAlarm. The REN

for other devices will be identified on a label on the product in the FCC product identifier

or listed separately. If there is a product identifier number, it will be in a format as

US:AAAEQ##TXXXX. The ## is the REN number shown without a decimal point (e.g.,

03 is a REN of 0.3).

If this WaterAlarm causes harm to the telephone network, the telephone company will

notify you in advance that temporary discontinuance of service may be required. But if

advance notice isn’t practical, the telephone company will notify the customer as soon as

possible. Also, you will be advised of your right to file a complaint with the FCC if you

believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations or

procedures that could affect the operation of the equipment. If this happens, the telephone

company will provide advance notice in order for you to make necessary modifications to

maintain uninterrupted service.

If trouble is experienced with your WaterAlarm, for repair or warranty information,

please contact Control Products at 952-448-2217. Other contact numbers and information

can be found at the end of this instruction manual. If the equipment is causing harm to

the telephone network, the telephone company may request that you disconnect the

equipment until the problem is resolved.

If your home has specially wired alarm equipment connected to the telephone line ensure

the installation of your WaterAlarm does not disable your alarm equipment. If you have

questions about what will disable alarm equipment, consult your telephone company or a

qualified installer.

WARRANTY

Warrantor: Dealer, Distributor, Retailer, Manufacturer

Warranty and Remedy:

We believe the WaterAlarm is a superior product. Although we take extreme pride in producing and

testing a product that will function properly, we cannot guarantee that there will never be a defective

unit or that a unit will function on all the thousands of phone lines and communication equipment in

existence. For thisreason, it must be clear thatthe Warrantors are not insuring your premises or

guaranteeing that there will not be damage to your person or property if you use this Product. If you

are not comfortable with our Limited Warranty, or completely satisfied with the Product, we

encourage you to return the unused Product for a full refund within 30 days of purchase. Thank you

for your understanding.

OneYear Limited Warranty - Control Products, Inc. warrantsits product to be free from defects in

material and workmanship under normal use for one year, and is not responsible for consequential

damages or installation costs of any nature. In the event that the Product does not conform to this

Warranty at any time during the period of one year from original purchase date, Warrantor will

repair the defect and return it to you at no charge. IMPORTANT: The Warranty is limited to

replacement of the Product ONLY. Secondly, because every phone line differs, we strongly

encourage you to fully test this Product in its actual application. This should includea full test,

involving the Product actually dialing to its designated locations and someone verifying the proper

response.

This Warranty shall terminate and be of no further effect at the time the Products is 1) damaged by

extraneous causes such as fire, water, power surge or spike, lightening, etc., or not maintained as

reasonable and necessary; 2) modified; 3) improperly installed; 4) repaired by someone other than

the Warrantor; 5)usedin a manner or purpose for which the Product was not intended.

WARRANTORS’ OBLIGATION UNDER THIS WARRANTY IS LIMITED TO REPAIR OR

REPLACEMENT OF THE PRODUCT ONLY. THIS WARRANTY DOES NOT COVER

PAYMENT OR PROVIDE FOR THE REIMBURSEMENT OF PAYMENT FOR INCIDENTAL

OR CONSEQUENTIAL DAMAGES.

It must be clear that the Warrantors are not insuring your premises or guaranteeing that there will not

be damage to your person or property is you use this Product. The Warrantors shall not be liable

under any circumstances for damage to your person or property or some other person or that

person’s property by reason of the sale or use of this Product, or its failure to operate in the manner

in which it is designed. The Warrantors’ liability, if any, shall be limited to the original cost of the

Product only. Use of this product is at your own risk.

Procedures for Obtaining Performance for Warranty:

Inthe event that the Product does not conform to this Warranty, the Product should be shipped or

delivered freight prepaid to Warrantor with evidence of original purchase. If in any way you’re not

comfortable withthis product or its Limited Warranty, we encourage you to return it, unused within

30 days of original purchase date with evidence ofthe purchase date.

To return a product to Control Products, Inc.:

All products being returned to Control Products, Inc. must have a valid Returned Goods

Authorization Number (RGA #) from Control Products, Inc., regardless of why the product is being

returned. Warranty returns will be honored only with a RGA #. Ship warranty return products

prepaid to Control Products, Inc., 1724 Lake Drive West, Chanhassen, MN 55317. Control

Products, Inc. will, at its option, either repair or replace the product free of charge and return the

repaired unit or replacement unit at the lower cost shipping prepaid. Products returned for credit are

subject to a 25% restocking charge. Returns resulting from errors by the seller are not subject to this

charge. All returns must include evidence of original purchase, showing purchase date. The RGA #

should be clearly marked on the outside of the package containingthe product.

To request an RGA #, call Control Products, Inc. at 952-448-2217 and ask for Customer Service.

Failure to have an RGA # may result in lost product or significant delays in handling your return.

Products without an RGA # clearly marked on the outside of the package are not the responsibility

of Control Products, Inc.

This page intentionally blank

This manual may not be reproduced, modified

or distributed without permission from Control Products, Inc.

Document # 42420026A, Revised 10-3-05

Inhaltsverzeichnis

Andere Protected Home Sicherheitssystem Handbücher

Protected Home

Protected Home HomeSitter HS-700 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung