Protege Iw630 Bedienungsanleitung

Inwall LCR Speakers can be used in any position of a home theater

speaker system. A single Inwall LCR Speaker can be used for the

front center channel, or a pair can be used for left and right in the

front or rear of the system.

Using as a Center Channel Speaker

Inwall LCR Speakers have been designed to blend seamlessly

with all Proficient inwall and ceiling speakers. For center channel

applications, install the Inwall LCR Speaker horizontally into the

wall as close to the screen as possible. This most often means

it will need to be installed just above or below the television.

Vertically lining it up with the left and right speakers while not

necessary, will improve the performance. (See Diagram 1)

Using as Front Left and Right Speakers

When using Inwall LCR Speakers for front left and right speakers,

position them vertically with the tweeter towards the screen. Align

them with the center of the screen for optimal results. (See Diagram 1)

The speakers should be placed so that they form an equilateral

triangle. (See Diagram 2) If the speakers are positioned far away from

the primary listening area, adjust the pivoting tweeters so they are

pointed toward the primary listening area.

Note: To avoid possible damage to the pivoting tweeters, read the

section entitled “SPEAKER ADJUSTMENTS” in this manual prior to

performing the tweeter adjustment.

SPEAKER PLACEMENT

Diagram 2:

Ideal Placement

A=B=C

Ideal

Listening

Zone

Left Speaker Center Speaker Right Speaker

TOP VIEW

Diagram 1:

Speaker Positioning

Before installing your speakers into the wall, you should consider

the placement carefully, taking into account the location of

electrical, plumbing and other fixtures.

Contact your Dealer for assistance if you are unsure of the best

location for your particular listening environment.

INSTALLATION CONSIDERATIONS

Inwall LCR Speakers

IW655 • IW630 • IW555 • IW530

OWNER’S MANUAL

New Construction - Unfinished Walls

A Pre-Construction Bracket, available from your Proficient dealer,

may be installed prior to drywall application across studs (up to

16" on-center) where a speaker will be located. After the hole is cut

and the drywall is installed, the speakers are then easily installed

following the instructions for mounting in “Finished Walls” below.

Finished Walls

Prior to the actual installation of the speakers, it will be neces-

sary to run cables to the speaker locations. See your Dealer for

ore information about cable installation. After the cable has been

properly installed, you are ready to mount the speakers. Following

the simple steps listed below will result in a professional looking

installation:

1. Determine the best area to mount your speakers. This area of

the wall should be free of obstructions such as electrical con-

duit, HVAC ducts, or water lines. This can best be determined

by noting the placement of fixtures and gaining access to an

attic or crawl space for further analysis of the location of such

obstacles.

2. Find the studs nearest the desired speaker mounting location.

We highly recommend using a good stud-finder tool for this

procedure. If you are lining up the speakers to some other

object or molding in the room, make sure you consider the size

of the baffle, which extends beyond the mounting hole.

3. Mark the hole. A template for setting the hole is provided in the

box. Position the template in the desired position and pencil an

outline on the wall.

4. Cutting the hole. CAUTION: This is the most important part

of the entire installation. If you are not certain whether any

obstructions exist behind the desired mounting area, you

should start by cutting a small hole in the center of your pen-

ciled mounting hole with a drywall saw. Cut at a 45˚ angle

towards the inside of the hole (See Diagram 3). Cutting the small

hole at this angle will make drywall repair much easier, using

the piece cut out. Once you have determined there aren’t any

obstructions in your desired mounting location, start cutting

the finished hole at a 90˚ angle to the wall surface.

5. Add insulation. If the area in the wall is not already insulated, add

an adequate amount of insulation material to loosely cover the

back of the speaker. If the insulation material used is faced with

foil or paper, position the foil or paper away from the speaker.

CAUTION: Speaker components can get hot while playing music

at moderate to high volume levels. There should be nothing at

all touching the speaker. Material in proximity to the back of

the speaker must have at a minimum 1" or 26mm clearance for

non-flammable materials and more for flammable materials like

plastic vapor barriers.

MOUNTING SURFACE PREPARATION

TOP VIEW OF WALL

First Cut

Second Cut

45˚

90˚

Diagram 3:

Wall Cut Out

The unique integrated six foot mounting system incorporated

into each Inwall LCR Speaker allows for a quick installation by

following these easy steps:

1. Remove the grille from the speaker baffle.

2. Attach the speaker cable (observing the proper polarity with

your amplifier, + to + and – to –). Make sure the left channel

of the amplifier is connected to the left speaker, and the right

channel is connected to the right speaker, etc.

3. Make sure the mounting feet are turned inward to clear the

opening, and insert the speaker into the wall. Note: The speaker

is designed to flex and conform to any small imperfections in the

wall’s surface. Tighten the six screws on the front of the baffle

only enough to make the speaker become snug against the

wall. As you tighten the screws, the feet will automatically flip

into an outward position (See Diagram 4), thereby clamping the

drywall between the feet and the speaker.

CAUTION: Over tightening may warp the baffle, crack the wall

or cause difficulty in aligning the grille.

4. Reattach the grille onto the speaker baffle.

SPEAKER INSTALLATION

Mounting Feet Speaker

Diagram 4:

Mounting Feet

We recommend painting your grille prior to installation. If you

decide to paint it in the future, it's best to remove the grille by

simply detaching it from the speaker. Do not paint the grille while

it's installed on the speaker.

Before painting, be sure to remove the cloth material from

beneath the grille. Once painted, place the cloth back to its

position beneath the grille.

When painting, be careful not to clog the holes of the grille.

The sound of the speaker will be dramatically reduced if the perfo-

rations in the grille are covered in paint.

Proficient recommends only light spray painting using five parts

thinning agent to one part paint.

PAINTING THE GRILLE

Your Inwall LCR Speaker comes with the tweeter facing straight

out from the baffle. This will result in the overall smoothest

response. However, depending on your particular primary area,

room acoustics, ceiling height, or personal preference, you may

find the sound more pleasing by pointing the tweeters in a

particular direction. If additional treble is desired in the primary

listening area, point the tweeter towards that area. Push gently

at the edge of the tweeter to point it in the desired direction. (See

Diagram 5)

CAUTION: Avoid touching the metal dome tweeter, as damage

may occcur.

For home theater use, we recommend the following tips:

• If the Inwall LCR Speaker is being used as a main front channel,

the tweeter should be angled towards the listener.

• If the Inwall LCR Speaker is being used for a rear surround

channel, you may wish to pivot the tweeter away from the

listener to achieve a more diffused sound.

Tweeter Adjustment:

The switch labeled TREBLE allows for ±3dB of treble adjustment.

Your speakers were shipped with the treble switch in the middle

position, providing the most linear frequency response. If you

desire more treble, move the switch to the “+” position, and the

tweeter will play 3dB higher. If you desire less treble, move the

switch to the “–” position, and the tweeter will play 3dB lower. To

return to the neutral setting, push the switch back to the middle

position. (See Diagram 6)

Woofer Adjustment:

The switch labeled BASS allows for ±3dB of bass adjustment. Your

speakers were shipped with the bass set to the middle position.

This setting provides the flattest bass frequency response. If you

desire more bass, push the switch to the “+” position and the bass

will play 3dB higher. If you desire less bass, push the switch to

the “–” position and the bass will play 3dB lower. To return to the

neutral setting, push the switch back to the middle position. (See

Diagram 6)

SPEAKER ADJUSTMENTS

Diagram 5:

Tweeter

Diagram 6:

Adjustment Switches

Push Tweeter Here

Bass Adjustment Switch Treble Adjustment Switch

SPEAKER SPECIFICATIONS

Woofers:

Tweeter:

Contour Switches:

Power Handling:

Frequency Response:

Impedance:

Sensitivity:

Grille:

Dimensions (H x W x D):

Wall Cut Out (H x W):

IW655

Two 6½" Kevlar®Cones

1" Pivoting Aluminum Dome

±3dB Bass & Treble

150 Watts

50Hz - 20kHz

8

90dB 1W/1m

Thin-Bezel held by

Neo Magnets

9" x 16⁄" x 3"

7½" x 14½"

IW555

Two 5¼" Kevlar®Cones

1" Pivoting Aluminum Dome

±3dB Bass & Treble

125 Watts

60Hz - 20kHz

8

88dB 1W/1m

Thin-Bezel held by

Neo Magnets

8" x 15⁄" x 3⁄"

6⁄" x 14½"

IW530

Two 5¼" Graphite Cones

1" Pivoting Aluminum Dome

±3dB Bass & Treble

100 Watts

65Hz - 20kHz

8

88dB 1W/1m

Thin-Bezel held by

Neo Magnets

8" x 15⁄" x 3⁄"

6⁄" x 14½"

IW630

Two 6½" Graphite Cones

1" Pivoting Soft Dome

±3dB Bass & Treble

125 Watts

55Hz - 20kHz

8

90dB 1W/1m

Thin-Bezel held by

Neo Magnets

9" x 16⁄" x 3"

7½" x 14½"

Features and specifications are subject to change without notice.

1800 South McDowell Blvd • Petaluma, CA 94954

800.472.5555 • Fax 707.283.5901 • proficientaudio.com

Proficient® is a registered trademark of Core Brands, LLC, a subsidiary of Nortek, Inc.

Proficient Audio Systems (“Proficient”) warrants to the original retail pur-

chaser only (“you”) that this product will be free from defects in materials and

workmanship for a period of ten years (the “Warranty Period”), subject to the

limitations and exclusions set out in this Limited Warranty. This warranty is not

transferable to subsequent owners of the product. If you discover a defect in

material or workmanship within the Warranty Period, you can obtain warranty

service by contacting Proficient during the Warranty Period at 800.472.5555 or

[email protected] or by sending the product to Core Brands

at 12471 E. Riverside Drive, Eastvale, CA 91752 or to the dealer from whom

you purchased the product. Defective products must be shipped, prepaid

and insured, together with proof of purchase. Warranty service requests made

without proof of date of purchase will be denied. Freight collect shipments

will be refused. It is preferable to ship this product in the original shipping

container to lessen the chance of transit damage. In any case, the risk of loss or

damage in transit is to be borne by the purchaser.

If, upon examination by Proficient or its authorized dealer, it is determined that

the unit is in fact defective, Proficient will, at its option:

• Repair or replace the product at no additional charge; or

• If the model is no longer available and can not be repaired effectively, replace

the unit with a current model of equal or greater value. In some cases where

a new model is substituted, a modification to the mounting surface may be

required. If mounting surface modification is required, Proficient assumes no

responsibility or liability for such modification.

Proficient will bear the cost of returning the repaired or replaced product to

you, freight prepaid. All replaced parts and product become the property of

Proficient Audio Systems. The foregoing is your sole and exclusive remedy for

breach of warranty. If the product is not found to be defective, Proficient will

contact you to arrange for return of the product to you, at your expense.

EXCLUSIONS:

• This Warranty does not include service or parts to repair damage caused by

accident, disaster, misuse, abuse, negligence, inadequate packing or shipping

procedures, commercial use, voltage inputs in excess of the rated maximum

of the unit, or service, repair or modification of the product by unauthorized

dealers. This Warranty also excludes normal cosmetic deterioration caused by

environmental conditions.

• This Warranty will be void if:

• the Serial Number on the product has been removed, tampered with or defaced.

• the product was not purchased from an authorized dealer.

THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER

EXPRESSED AND IMPLIED WARRANTIES. PROFICIENT EXPRESSLY DISCLAIMS

ALL SUCH OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO IMPLIED

WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE

AND NON-INFRINGEMENT. In no event will Proficient be liable for any incidental

or consequential damages arising out of the use or inability to use the product,

even if Proficient has been advised of the possibility of such damages, or for any

claim by any other party. Notwithstanding the above, if you qualify as a“con-

sumer” under the Magnuson-Moss Warranty Act, then you may be entitled to any

implied warranties allowed by law for the Warranty Period. Further, some states

do not allow limitations on how long an implied Limited Warranty lasts or allow

the exclusion or limitation of consequential damages, so such limitations may not

apply to you.

ATTENTION TO OUR VALUED CONSUMERS:

To insure that consumers obtain quality pre-sale and after-sale support and

service, Proficient products are sold exclusively through authorized dealers.

Proficient products are not sold online by Proficient or its authorized dealers,

and this warranty is VOID if the products have been purchased from any internet

reseller. To determine if your Proficient reseller is authorized, please call Proficient

at 800.472.5555 or go to proficientaudio.com.

LIMITED TEN-YEAR WARRANTY

For technical inquires, please call 800.472.5555 or e-mail us at techsupport@proficientaudio.com. We are available to assist you

every weekday, except holidays, between the hours of 7:00 a.m. and 5:00 p.m. PST.

9901320 (Rev A)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Protege Sprecher Handbücher

Protege

Protege W852 Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung

Protege iw630 Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken