Protocol DRONIUM 3X Bedienungsanleitung
DRONIUM 3X
DRONE WITH LIVE STREAMING CAMERA
Thank you for your purchase of Protocol’s Dronium 3X Drone
with Live Streaming Camera. You are about to experience
the best of what remote control flight has to offer. We strongly
recommend that you take the time to read this manual
thoroughly. It contains many tips and instructions on how to
get the most out of this aircraft and maintain it for a long life.
As with any aircraft, this is a precision flying machine.Treat it
well and enjoy all the fun it has to offer, flight after flight.
THANK YOU.
01 Safety & Precautions
02 Parts
04 Remote Battery & Blade Guard Installation
05 Charging the Drone
06 Start-Up Procedure
08 Operation
10 Tips on 360° Flips
12 Speed Modes
13 Trim Adjustment
14 Troubleshooting
15 Flying Outdoors
16 Shooting Photo/Video
17 Replacement Parts & Limited Warranty
TABLE OF CONTENTS
SAFETY WARNINGS
•Read and follow instructions on how to synchronize and calibrate
electronics before each flight.
•To prevent damage to people or property, always avoid contact with
other objects while in flight.
•Inspect aircraft prior to each flight and do not fly if damaged.
•Never expose product or any of its electronic parts to moisture, water,
or heat sources.
•To prevent overheating, allow battery a cool-down period
before recharging.
•To prolong engine life, allow a cool-down period between flights.
•Use only the charger and/or charging cable that is suplied with
this item.
•Do not strike, cut, or pierce the internal battery or subject it to
hard impacts.
•Do not mix old and new batteries or mix different types of batteries.
•Never attempte to modify function of vehicle or controller or attempt
repairs using parts other then those supplied by Protocol. Spare parts
are available at www.ProtocolNY.com
HAVE FUN, BUT SAFETY FIRST!
THIS DEVICE USES COMPONETS THAT OPERATE AT HIGH SPEEDS.
AS WITH ANY SUCH DEVICE, USE CAUTION TO OPERATE SAFELY.
FAILURE TO FOLLOW ANY OF THESE GUIDELINES MAY RESULT IN BODILY
INJURY OR DAMAGE TO PERSONAL OR PUBLIC PROPERTY.
1
PARTS
DRONE
1. Canopy
2. Blade Guard
3. Blade
4. Battery Compartment
5. Camera
6. ON/OFF Switch
53
2
4
1
2
6
REMOTE
1. 2.4G Antenna
2. Power Switch
3. Trim Forward/Backward
4. Flip 360°
5. Forward/Backward
6. Bank Left/Right
7. Video
8. Photo
9. Trim Bank Left/Right
10.Indicator Light
11.Throttle
12.Turn Left/Right
13.Speed Mode Selector
14.Take Off/Landing
15.Calibration
SPARE PARTS INCLUDED
- Replacement Blades
- Blade Guards
- Screwdriver
PARTS
14
15
1
13
2
4
10
3
65
9
7
8
3
11 12
INSTALLING THE BLADE GUARD
If not already installed, install the included blade guards by snapping them in
and tightening the screws. Make sure the blade guards are secure and snug.
NOTE:
Loose blade guards may interfere
with propeller movement and cause
a crash. If the drone crashes, double
check to make sure the blade guard
is not loose. If it is, re-tighten
before flying.
Battery cover
REMOTE BATTERY AND BLADE GUARD INSTALLATION
1. Install batteries carefully.
2. Do not mix old and new batteries.
3. Do not mix different types of batteries.
Unscrew and remove battery cover from controller. Insert 4 x ‘AA’ batteries
according to indicated polarities. Replace and screw back in battery cover.
4
REMOTE BATTERY AND BLADE GUARD INSTALLATION CHARGING THE DRONE BATTERY
1. Make sure the drone is turned off.
2. Pull out the cartridge battery from the drone.
3. Connect the USB charging cable to the battery.
4. Plug the charger into a USB port. The USB light will turn off while charging
and will turn on once fully charged.
5. Plug the battery back into the drone and close the battery cover.
Charging time: 150 minutes --- Flying time: approximately 12-15 minutes
CAUTION WHEN CHARGING
1. When charging, place product on a dry, well-ventilated surface and keep
away from heat sources.
2. Always use adult supervision while charging.
3. In order to increase battery longevity, avoid repeat charging and excessive
discharging.
4. As battery temperature is high immediately after flight, charge after cooling
down for higher efficiency.
5. Do not strike or subject battery to hard impacts or sharp surfaces.
6. Do not use any other charger than that which is supplied with this item.
7. Do not use or leave battery near a heat source such as fire or space heater;
exposure to heat may result in reduced performance or in some cases
dangerous conditions.
8. If battery is left in charging state for an extended period of time after being
fully charged, the battery may automatically discharge.
9. Never leave the battery unattended during charging.
10. Do not disassemble battery.
11. Do not submerge battery in water. 5
DO NOT CHARGE OVERNIGHT OR BEYOND
THE CHARGING TIME STATED. DO NOT LEAVE
BATTERY UNATTENDED.
*Battery: Li-Po, 3.7V, 1800mAh
Lights are steady Power is over 70% - will perform flips
Lights slowly flash once every 2 seconds
Power is under 70% - will continue to fly
but will no longer perform flips –
approximately 8-9 minutes left of flight time
Lights quickly flash twice every second Power is under 20% - approximately
2 minutes left of flight time
BATTERY SIGNALS
If you purchased extra batteries, allow the engines to cool between flights in order
to prolong engine life.
START-UP PROCEDURE
NOTE:
1. While the drone is in process of synchronizing or calibrating, the lights
will flash quickly. When the process is completed, the lights will go
steady. This is your indication that the process is completed.
2. If after 30 seconds, it has not recognized the drone, turn off the controller
and repeat Start-Up procedure.
3. If the Dronium 3X is unsteady in flight, it may not have been able to
calibrate properly. Power down both drone and remote and restart
pre-flight procedure, including re-calibration of the altitude sensor.
4. For the Altitude Sensor to calibrate properly, the drone must be
synchronized already, but the engines not spinning yet. You cannot
calibrate while the propellers are turning. You have to calibrate before
you start the engines.
Before flying, the drone and transmitter must be turned on in sequence and
synchronized. Once synchronized, you must press the calibration button so the
Altitude Sensor can set properly.
1. Turn on the drone and place it on an even surface. The white lights on the
drone are at the front and the red are at the back.
2. Turn on the remote control.
3. Both indicators on the drone and the remote will flash while they are syncing.
4. Push the throttle up and then down to sync. You will hear two beeps and the
lights will go steady.
5. Next, you must calibrate the Altitude Sensor. Press the calibration button
once. Lights will flash quickly and will go steady when finished. Your drone
is now synchronized, calibrated, and in stand-by mode awaiting Engine
Idle command.
6
Inhaltsverzeichnis
Andere Protocol Drohne Handbücher
Protocol
Protocol KODIAK GPS Bedienungsanleitung
Protocol
Protocol VIDEODRONE FX Bedienungsanleitung
Protocol
Protocol dronium III AP Bedienungsanleitung
Protocol
Protocol neo-drone AP Bedienungsanleitung
Protocol
Protocol AEROFLUX AP Bedienungsanleitung
Protocol
Protocol AXIS WITH CAMERA RC DRONE Bedienungsanleitung
Protocol
Protocol VIDEODRONE AP Bedienungsanleitung
Protocol
Protocol AeroDrone 6182-1DH Bedienungsanleitung
Protocol
Protocol VENTO WIFI Bedienungsanleitung
Protocol
Protocol DOT VR Bedienungsanleitung
Protocol
Protocol Dronium One AP Bedienungsanleitung
Protocol
Protocol Kaptur Bedienungsanleitung
Protocol
Protocol AeroDrone Bedienungsanleitung
Protocol
Protocol NEO-DRONE WIFI Bedienungsanleitung
Protocol
Protocol TERRACOPTER Bedienungsanleitung
Protocol
Protocol Explorer GPS Bedienungsanleitung
Protocol
Protocol AIR HOVER RACER Bedienungsanleitung
Protocol
Protocol OCEANA Bedienungsanleitung
Protocol
Protocol AERO 2.0 Bedienungsanleitung
