ProVista Technology TSW600 Basic Bedienungsanleitung

Operating Manual TSW600 Basic

Index

Introduction ..........................…………………………………………………....... 1

Description of symbols .........…………………………………………………....... 2

1 About this manual .........………………………………………………………...... 2

1.1 Applicability .............………………………………………………………....... 2

1.2 Users .....................………………………………………………………........ 2

2 Safety .........................…………………………………………………………..... 3

2.1 Proper usage ...........……………………………………………………….…..3

2.2 Improper usage .......……………………………………………………….….. 3

2.3 Other risks ............…………………………………………………………….. 3

2.4 Fault behaviour ..............………………………………………………….…...3

3 Description ................……………………………………………………………... 4

3.1 Construction ..........…………………………………………………………..... 4

4 Installation ............…………………………………………………………….… 4-6

4.1 Mounting .............…………………………………………………………….... 4

4.1.1 Mounting location………………………………………………………….....

4.1.2 Mounting the inverter……………………………………………………......

4.2 Connection .............………………………………………………………....... 5

4.2.1 AC output of the inverter…………………………………………………....

4.2.2 Connecting the battery to the inverter………………………………..........

5 Operation ...................………………………………………………………...... 6-7

5.1 Switching the power supply on/off ..……………………………………….... 6

5.2 Switching off the power supply …………………………………………….... 6

5.3 Protection function ...........………………………………………………........ 7

6 Care, maintenance and service ……………………………………………….... 7

7 Technical data …………………………………………………………………...... 8

7.1 Device data …………………………………………………………………..... 8

8 Fault and troubleshooting ......………………………………………………….... 9

9 Part list ………………………………………………………………………….....

10 Exclusion of liability …………………………………………………………......10

11 Contact …………………………………………………………………………...11

Introduction

The TSW600 Basic is stand-alone inverter for PV battery systems. They convert the battery’s

DC voltage into pure sine wave AC voltage, this can provide nice power to any normal AC

appliances such as consumer electronics, tools, household appliances, lamps, etc.

TSW600 Basic can provide power of 230V AC /50Hz.

Description of symbols

1. The structure of the warning notices

SIGNAL WORD

2. Danger levels in warning notices

Danger level Probability of occurrence Consequences resulting

from non-compliance

DANGER Imminent threat of danger Death, serious bodily injury

WARNING Possible threat of danger Death, serious bodily injury

CAUTION Possible threat of danger Minor bodily injury

CAUTION Possible threat of danger Property damage

3. Notes

NOTE

Note on easier and safer working habits.

zMeasures for easier and safer working habits.

1 About this manual

These instruction manual are part of the product.

zRead these operating instructions carefully before use,

zKeep them over the entire lifetime of the product,

zPass them on to any future owner or user of this product.

1.1Applicability

This manual describes the function, operation ，installation, and maintenance of the

stand-alone inverters.

1.2Users

Installation, commissioning, operation, maintenance and take-down of the inverter may only

be done by professional worker in accordance with the applicable on-site installation

regulations. The professional worker must be familiar with this operating manual and follow

the instructions contained herein.

The end user may only perform operating functions.

2 Safety

2.1 Proper usage

The inverters are exclusively intended for use in off-grid power supplies in accordance with

these operating instructions. Any other use is regarded as improper use of the device.

2.2 Improper usage

zThe inverter must never be connected to the utility grid or a generator.

zThe casing must not be opened and should not show any damage.

zThe pre-fitted battery cables must not be extended.

zThe inverter can not be connected in parallel way.

2.3 Other risks

WARNING

Danger of fire and explosion

zA stand-alone power supply system (including inverter) must not be installed, operated or

maintained in locations where inflammable gases and vapors can occur, in dusty

environments, or in the vicinity of solvents.

zNo open fires, flames or sparks in the vicinity of the batteries.

zEnsure that the room is ventilated.

Battery acid

zAcid splashes on skin or clothing should be immediately treated with soap suds and rinsed

with plenty of water.

zIf acid splashes enter the eyes, immediately rinse with plenty of water and seek medical

advice.

2.4 Fault behaviour

DANGER

Operating the system is dangerous in the following situations:

zThe inverter does not appear to work at all.

zThe inverter, mains cable or battery cables are visibly damaged.

zEmission of smoke or fluid penetration.

zWhen parts are loose.

¾In these cases immediately turn off inverter and remove the inverter from the battery

and consumer devices.

3 Descriptions

3.1 Construction

TSW600 Basic include following components:

1. LED indication for operating modes

2. ON/OFF switch

3. Aviation plug with 1 m cable (230V AC & 50Hz Output)

4. Fuse box (35A X 2pcs)

5. Battery connector(Black): Negative polarity (Connect to Black cable with Ring connector,

Approx. 1.5m long)

6. Battery connector(Red): Positive polarity (Connect to Red cable with Ring connector,

Approx. 1.5m long)

4. Installation

4.1 Mounting

4.1.1 Mounting location

Ensure that the mounting location complied with below requirements:

zMount in a dry, dust-free, ventilated indoor place

zMount on flat surface.

zMount upright on the wall, on concrete

or on any other non-flammable

surface.

zThe mounting location must be

protected from unauthorized access,

especially by small children.

zDistance between inverter and battery:

please note that the pre-fitted cables

must not be extended.

zMinimum clearance of approx. 25 cm

above and below to allow free air

circulation.

4.1.2 Mounting the inverter

zMark and drill the upper holes

(Ø 5 mm).

zInsert the dowels and screw in the

screws. Do not screw tight at this

moment.

zHang the inverter on the two screws

and mark the lower holes.

zRemove the inverter and drill the two

lower holes.

zInsert the dowels.

zHang the inverter on the two upper

screws and screw in the lower screws.

zScrew all screws tight.

4.2 Connection

WARNING

Danger of explosion from sparking! Danger of electric shock!

zThe inverter may only be connected to the local consumer devices and the battery by

trained personnel and in accordance with the applicable regulations.

zConnections must always be made in the sequence described below

zThe cables pre-fitted to the inverter must not be damaged

4.2.1 AC output of the inverter

zConnect suitable AC socket with pre-fitted AC Output cable, Brown cable connect to L,

Blue cable connect to N, Yellow & Green cable connect to GND

zConnect Male aviation plug to AC Output of inverter

4.2.2 Connecting the battery to the inverter

WARNING

Danger of explosion from sparking! Danger of electric shock!

zBefore connecting the battery, ensure that no consumer devices are switched on and the

ON/OFF switch is in the "OFF" setting

zEnsure that the polarity of the battery connection is correct

zThe cables pre-fitted to the inverter must not be extended

zFollow the instructions of the battery manufacturer

¾Turn the ON/OFF switch to the "OFF" setting

¾Ensure that the connection to the mains grid has been carried out correctly

¾An easily accessible disconnection device should be connected to the battery cables

immediately next to the battery. The disconnection device should consist of a DC circuit

breaker or a DC fuse.

¾Connect the red battery cable to the positive terminal + of the battery

¾Connect the black battery cable to the negative terminal – of the battery

¾Ensure that the connections are tight

CAUTION

Inverter can only be connected to 12V battery. (10.5-14.5V)

5 Operation

The inverters are equipped with a standby system. To avoid unnecessarily discharging the

battery, in this operating mode switches off the inverter manually when no consumer device is

connected and switches on manually when a consumer device is switched on.

5.1 Switching the power supply on/off

5.1.1 Switching on the power of inverter

5.1.2 Red LED turns on at the first 3 seconds and then Green LED permanent illuminated

5.1.3 Connect consumer device to the inverter

5.1.4 Turn on consumer device

5.2 Switching off the power supply

If power is not required for a longer period of time, e.g. when

you are absent, it’s recommended to switch off the inverter.

5.2.1 Switch off the power of inverter

5.2.2 Turn off the power of consumer device

Notes

The LED of Power permanently illuminated green when switch is on.

The LED of Fault illuminated red when problem happened.

5.3 Protection function

zNoise emission

¾The inverter has a fan that automatically switches on when the device heats up, e.g. in

high ambient temperatures or long-term heavy loads. The fan switches off again as soon

as the device has stopped generating excessive heat.

Notes

Inside Temp is more than 50℃or load power is higher than 500Watt, the fan switch on

automatically,

Temp is lower than 40℃, the fan switch off automatically

zDeep discharge protection

¾The inverter protects the battery from deep discharge. With low battery voltage around

10.5 V, inverter alarm and Red LED turn on, pls switch off inverter till battery is charged.

¾If the voltage of battery is lower than 10V, inverter will switch off automatically to protect

battery is deep discharged.

Notes

Before restart inverter, wait till battery is charged and voltage is higher than 12.5V.

Restart inverter.

zOver voltage protection

¾The inverter protects itself from over voltage. With high input voltage around 15 V from

battery, inverter will turn off automatically

Notes

Before restart inverter, check the output voltage from battery is lower than 14.5V

Restart inverter

zOver load protection

¾The inverter switch off automatically when output power is higher than 650Watt.

¾Inverter will automatically restart after 5 seconds, if the output power still higher than

650Watt, it will keep off. Inverter will detect 3 times automatically, if the output power still

higher than 650Watt, inverter will turn off until it’s restarted manually.

zOver temperature protection

¾The inverter will turn off automatically when the inside temperature is higher than 65℃

Notes

After inverter get cool, restart it manually

6 Care, maintenance and service

The inverter is maintenance-free. If functional faults occur, please consult your dealer and

present the payment receipt / invoice.

zBefore cleaning the inverter, switch off all consumer devices and switch off the inverter via

the ON/OFF switch.

zRegularly clean the outside of the case with a damp duster cloth. Do not use solvents and

wet rag.

zEnsure that the ventilation slots on the side and lower sides of the device are not

obstructed and that the air can freely circulate. If necessary, remove dust by vacuuming.

Inhaltsverzeichnis

Andere ProVista Technology Wechselrichter Handbücher

ProVista Technology

ProVista Technology GTW1500HF Bedienungsanleitung

Beliebte Wechselrichter Handbücher anderer Marken

Fourgroup

Fourgroup Easy Bedienungsanleitung

Velleman

Velleman PI300M Bedienungsanleitung

Sungrow

Sungrow SG350HX-US Bedienungsanleitung

WilTec

WilTec 61897 Bedienungsanleitung

SMA

SMA SUNNY BOY STORAGE 2.5 Bedienungsanleitung

Simplicity

Simplicity LANDLORD 316 Bedienungsanleitung

Santak

Santak SMAX 3000 Bedienungsanleitung

ATON

ATON RA.Store-3 Bedienungsanleitung

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Bedienungsanleitung

Tektronix

Tektronix CFG250 Bedienungsanleitung

Champion

Champion 200989 Bedienungsanleitung

Vanner

Vanner 20-500 Series Bedienungsanleitung

GE GEP Bedienungsanleitung

Astrel Group

Astrel Group Power Reducer Kurzanleitung

MULTIQUIP

MULTIQUIP GDP-5H Leitfaden

GoWISE

GoWISE PS1007 Bedienungsanleitung

Promate

Promate PM13500D ES Bedienungsanleitung

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Bedienungsanleitung