PTN TPUH-PSU12 Bedienungsanleitung

www.PTN-electronics.com

TPUH-PSU12

Integrated Switching Power Supply

Version: TPUH-PSU12_2018V1.4

User Manual

Integrated Switching Power Supply

PTN Electronics Limited www.PTN-electronics.com

Preface

Read this user manual carefully before using the product. Pictures are shown in this

manual for reference only. Different models and specifications are subject to real

product.

This manual is only for operation instruction, please contact the local distributor for

maintenance assistance. The functions described in this version were updated till March,

2018. In the constant effort to improve the product, we reserve the right to make

functions or parameters changes without notice or obligation. Please refer to the dealers

for the latest details.

Trademarks

Product model, PTN and its logo are trademarks of PTN Electronics Limited.

Any other trademarks mentioned in this manual are acknowledged as the properties of

the trademark owner. No part of this publication may be copied or reproduced without

the prior written consent of PTN Electronics Limited.

FCC Statement

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. It has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a commercial

installation.

Operation of this equipment in a residential area is likely to cause interference, in which

case the user at their own expense will be required to take whatever measures may be

necessary to correct the interference.

Any changes or modifications not expressly approved by the manufacture would void

the user’s authority to operate the equipment.

Integrated Switching Power Supply

PTN Electronics Limited www.PTN-electronics.com

SAFETY PRECAUTIONS

To insure the best from the product, please read all instructions carefully before using

the device. Save this manual for further reference.

Unpack the equipment carefully and save the original box and packing material for

possible future shipment

Follow basic safety precautions to reduce the risk of fire, electrical shock and injury

to persons.

Do not dismantle the housing or modify the module. It may result in electrical shock

or burn.

Using supplies or parts not meeting the products’ specifications may cause damage,

deterioration or malfunction.

Refer all servicing to qualified service personnel.

To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this

product near water.

Do not put any heavy items on the extension cable in case of extrusion.

Do not remove the housing of the device as opening or removing housing may

expose you to dangerous voltage or other hazards.

Install the device in a place with fine ventilation to avoid damage caused by

overheat.

Keep the module away from liquids.

Spillage into the housing may result in fire, electrical shock, or equipment damage. If

an object or liquid falls or spills on to the housing, unplug the module immediately.

Do not twist or pull by force ends of the optical cable. It can cause malfunction.

Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to

the device before cleaning.

Unplug the power cord when left unused for a long period of time.

Information on disposal for scrapped devices: do not burn or mix with general

household waste, please treat them as normal electrical wastes.

Integrated Switching Power Supply

PTN Electronics Limited www.PTN-electronics.com

Contents

1. Product Introduction....................................................................................................1

1.1 Feature..............................................................................................................1

1.2 Package List......................................................................................................1

2. Specification ...............................................................................................................2

3. Panel Description........................................................................................................3

3.1 Front Panel........................................................................................................3

3.2 Rear Panel.........................................................................................................4

4. System Connection.....................................................................................................5

4.1 Usage Precaution..............................................................................................5

4.2 System Diagram................................................................................................5

5. System Operation.......................................................................................................6

5.1 Button Control....................................................................................................6

5.2 RS232 Control...................................................................................................6

5.2.1 RS232 Control Software..........................................................................6

5.2.2 Basic Setting............................................................................................7

5.2.3 RS232 Communication Command..........................................................8

5.3 GUI Control......................................................................................................11

5.3.1 Control Menu.........................................................................................12

5.3.2 Voltage Setting Menu ............................................................................13

5.3.3 Network Menu .......................................................................................13

5.3.4 Password Menu.....................................................................................14

5.3.5 GUI Update............................................................................................14

6. Panel Drawing ..........................................................................................................15

7. Troubleshooting & Maintenance ...............................................................................16

8. Customer Service .....................................................................................................17

Integrated Switching Power Supply

PTN Electronics Limited 1 www.PTN-Electronics.com

1. Product Introduction

The product is an integrated switching power supply designed for converting AC into DC

power. It provide 2 input channels and 12 output channels, input voltage 100~240VAC,

output 5/12/24VDC, the max power consumption of single channel is 15W.

Base on the sequential control technology, when power on, the 12 output channels will

turned on orderly every 100ms.In addition, each output channel also can be switch

on/off via front panel button, RS232 commands or GUI, and the output voltage on each

output channel can be selected as 5/12/24V DC via the TACT Switch on rear panel,

RS232 command, or GUI.

1.1 Feature

Double input channel designed for ensuring the stable AC source.

Total 12 output channels, and each channel has three kinds of output voltage

(5/12/24VDC) can be selected.

Output channels can be switch on/off by via the front panel buttons, RS232

commands or GUI.

Output voltage (5/12/24VDC) can be selected via the TACT Switch on rear panel,

RS232 commands, or GUI.

Adopt sequential control technology.

Supports online software upgrading.

1.2 Package List

1 x TPUH-PSU12

2 x Mounting Ears & 6 x Screws

4 x Plastic Cushions

2 x Power Cords

12 x DC Power Cables (2-pin Phoenix Connector to DC)

12 x 2-pin Phoenix Connectors

1 x 3-pin Phoenix Connector

1 x RS232 Cable (DB9 to 3-pin Phoenix Connector)

1 x User Manual

Note: Please contact your distributor immediately if any damage or defect in the

components is found.

VGA/Stereo Audio/IR/RS232 Twisted Pair over single CAT cable

PTN Electronics Limited 2 www.PTN-Electronics.com

2. Specification

Input & Output

Input Port

AC1 & AC2

Input Voltage

100~240VAC 50~60Hz

Output Port

Total 12 DC port (2-Pin phoenix connectors)

Output Voltage

5V, 12V or 24V can be selectable.

Output Voltage Range

5V: 4.75~5.25V

12V: 11.4~12.6V

24V: 22.8~25.2V

Maximum output power

consumption of signal channel

5V:12W; 12V:15W; 24V:15W

Maximum output power

consumption for single supply

180W

Maximum output power

consumption for dual supply

180W

Control Part

Buttons Control

Front Panel: 01~12, total 12 buttons.

Rear Panel: Total 12 TACT Switches, named

SELECT.

RS232 Control

RS232 port (3-Pin phoenix connector).

Baud rate support 9600.

GUI Control

TCP/IP port (RJ45)

Default IP: 192.168.0.178

Port No.: 4001

General

Temperature

0 ~ +50℃

Humidity

10% ~ 90%

Dimension (W*H*D)

437mm x 44mm x 357mm

Net Weight

4.2Kg

Integrated Switching Power Supply

PTN Electronics Limited 3 www.PTN-Electronics.com

3. Panel Description

3.1 Front Panel

No.

Name

Description

①

FIRMWARE

USB port for updating system firmware.

②

AC1 & AC2

Input AC source indicators.

Green when the device is powered on and normal output.

Red when there is no power to the device.

Orange when the input voltage is too low or too high.

③

01~12

Output channel switching buttons and Activity LEDs, 12 in total.

Press the button to trun on/off the corresponding channel,

and the corresponding LED will turn green and keep on.

Long-press the button for 3 seconds or more to lock/unlock

the corresponding channel, and then the corresponding

LED will flash 3 times.

Note: Pictures shown in this manual are for reference only, different model and

specifications are subject to real product.

FIRMWARE

01 02 03 04 05 06

07 08 09 10 11 12

AC 2AC 1

12 3

Integrated Switching Power Supply

PTN Electronics Limited 4 www.PTN-Electronics.com

3.2 Rear Panel

No.

Name

Description

①

01~12

12 output channals.

A. DC: 2-Pin phoenix connector, connect with the device

needed to be powered.

B. SELECT: Press the TACT Switch to select the output

voltage among 5V, 12V, and 24VDC. In addition,

simultaneously long-press this buttons on channel 01 and

channel 02 for 3 seconds or more, the device will be

restored to factory setting.

C. 5/12/24V indicators:

Green when the current selected output voltage is work

normally.

Blinking slowly when the current channel is closed.

Blinking fastly when the current channel is short circuit

or over voltage.

②

RS232

Serial port, 3-Pin phoenix connector, connect with a control

device (such as PC) to control the product via RS232

commands.

③

TCP/IP

Ethernet port, connect with PC to control the product via GUI.

④

AC1& AC2

2 AC input channels. Input voltage is AC100~240V.

Note: Pictures shown in this manual are for reference only, different model and

specifications are subject to real product.

24V

12V

SELECT

AC100V 240V-

Tx Rx

RS232 TCP IP/

24V

AC100V 240V-

AC1 AC2

12V

+ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

234

Integrated Switching Power Supply

PTN Electronics Limited 5 www.PTN-Electronics.com

4. System Connection

4.1 Usage Precaution

Verify all components and accessories included before installation.

Make sure all components and accessories included before installation.

System should be installed in a clean environment with proper temperature and

humidity.

All of the power switches, plugs, sockets, and power cords should be insulated and

safe.

All devices should be connected before power on.

4.2 System Diagram

AC100V 240V-

Tx Rx

RS232 TCP IP/

24V

AC100V 240V-

AC1 AC2

12V

+ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

Powered Device 1 Powered Device 2 Powered Device 3

100~240VAC

RS232 Control

TCP IP Control/

Power Supply

Integrated Switching Power Supply

PTN Electronics Limited 6 www.PTN-Electronics.com

5. System Operation

5.1 Button Control

Switch on/off output channel:

Press the button 01~12 on front panel to switch on/off the corresponding output channel.

Lock/unlock output channel:

Long-press the button 01~12 for 3 seconds or more on front panel to lock/unlock the

corresponding channel, and then the corresponding LED will flash 3 times.

Note: The locked channel can’t be controlled via front panel button

、

RS232 commands

and GUI.

Select the output voltage:

Press SELECT on corresponding output channel to select the output voltage as 5V, 12V

or 24V.

Note: After switching the output voltage, the output channel will be turned off based on

overvoltage protection control, and it need to be turned on again via the corresponding

output channel switching button on front panel.

Restore Factory Defaults:

On rear panel, simultaneously long-press SELECT on channel 01 and channel 02 for 3

seconds or more, the device will be restored to factory setting.

5.2 RS232 Control

Connect a PC to the RS232 port on the rear panel, and then install the RS232 control

software on the PC, the product can be controlled by sending RS232 commands via the

RS232 control software.

5.2.1 RS232 Control Software

Installation Copy the control software file to the computer connected with the

product.

Uninstallation Delete all the control software files in corresponding file path.

Inhaltsverzeichnis

Andere PTN Stromversorgung Handbücher

PTN

PTN TPUH-PSU12-UL Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung