Pulsar PSDC04122T Bedienungsanleitung

PSDC04122T

v.1.0

PSDC 12V/2A/4x0,5A/TOPIC

Switched mode power supply for CCTV.

Edition: 2 from 25.02.2013

Supersedes the : 1 from 08.01.2013 edition

www.pulsar.pl PSDC04122T

Features:

•supply output 4x 0,5A/12V DC

•output voltage adjustment 12V÷ 15VDC

•4 outputs protected with 0,5A fuses

•wide range of supply voltage 176÷264VAC

•high efficiency 74%

•LED indication

•protections:

•SCP short-circuit protection

•OVP over voltage protection

•surge protection

•OLP overload protection

•warranty – 1 year from the production date

CONTENTS:

1. Technical description.

1.1 General description

1.2 Block diagram

1.3 Description of PSU components and connectors

1.4 Specifications

2. Installation.

2.1 Requirements

2.2 Installation procedure

3. Operating status indication.

3.1 LED indication

4. Operation and use.

4.1 Overload or short circuit at the PSU output

4.2Maintenance

1. Technical description.

1.1 General description.

The stabilized PSU PSDC04122T is intended for supplying CCTV devices requiring stabilised voltage of

12V DC. The output voltage adjustment range is adjusted via a potentiometer within the range of 12,0V÷15,0V DC.

The PSU features 4 outputs protected independently by glass fuses.

A failure (a short circuit) in the output circuit makes a fuse blow or an activation of the fuse and

disconnection of the circuit from the DC power supply (+U). The PSU is housed in a metallic enclosure with an

indication panel.

1.2. Block diagram. (fig.1).

Fig.1. Block diagram of the PSU.

www.pulsar.pl PSDC04122T

1.3. Description of PSU components and connectors.

Table 1. Elements of the PSU pcb (see fig. 2).

Element no. Description

[1] L1…..L4 (green) LEDs (indicating fuse activation)

[2] F1…F4 glass fuses in AUX (+) circuits

[3] IN supply input of the LB4 strip

[4] AUX1…. AUX4 outputs, COM (-) shared terminal

Fig.2. The view of the PSU’s pcb.

Table 2. Elements of the PSU (see fig. 3).

Element no. Description

[1] L-N 230 V AC power connectors, PE protection connector

[2] PSU module

[3] V

ADJ

, potentiometer, output voltage adjustment within the range of 12,0V÷15,0V DC

[4] LED indication of DC power status, main module of the PSU

[5] LB4 fuse strip, with power outputs and LED indication

Fig.3. The view of the PSU.

www.pulsar.pl PSDC04122T

1.4. Specifications:

- electrical specifications (tab.3)

- mechanical specifications (tab.4)

- operation safety (tab.5)

- operating specifications (tab.6)

Electrical specifications (tab. 3).

Supply voltage 176 ÷ 264V AC

Current consumption 0,18A @230VAC max.

PSU power 25Wmax.

Efficiency 74%

Output voltage 12V DC

Output current 4x 0,5A (ΣI = 2A) max. @12V

Output voltage adjustment range 12V÷ 15VDC

Ripple voltage 100mV p-p max.

Short-circuit protection SCP

LB4 STRIP

4x F 0,5A fuse

PSU MODULE

105% ÷ 150% of PSU power, electronic current limiting

Overload protection OLP 105% ÷ 150% of PSU power, electronic current limiting

Surge protection varistors

Overvoltage protection OVP

>16V (automatic recovery)

F1÷ F4 fuses F 0,5A/250V

Mechanical specifications (tab. 4).

Enclosure dimensions 230 x 176 x 59

(235 x 181 x 51+8) (WxHxD) [mm] (+/- 2)

Fixing 201 x 146 x 4 szt. Φ6 (WxH)

Net/gross weight 1,04/1,19 kg

Enclosure Steel plate, DC01 0,7mm colour: RAL 9003

Closing Cheese-head screw: at the front

Connectors Power supply: 230V AC: Φ0,63-2,05 (AWG 22-12)

AUX outputs: Φ0,51- 2,05 (AWG 24-12)

LB4: Φ0,51- 2,05 (AWG 24-12)

Notes The enclosure does not adjoin the assembly surface so that cables can be led.

Convectional cooling.

Operation safety (tab.5).

Protection class PN-EN 60950-1:2007 I (first)

Protection grade PN-EN 60529: 2002 (U) IP20

Electrical strength of insulation:

- between input (network) circuit and output circuits of the PSU (I/P-O/P)

- between input circuit and PE protection circuit (I/P-FG)

- between output circuit and PE protection circuit (O/P-FG)

3000V/AC min.

1500V/AC min.

500V/AC min.

Insulation resistance:

- between input circuit and output or protection circuit

100 MΩ, 500V/DC

Operating specifications (tab.6).

Operating temperature -10ºC...+50ºC

Storage temperature -25ºC...+60ºC

Relative humidity 20%...90%, without condensation

Vibrations during operation unacceptable

Impulse waves during operation unacceptable

Direct insolation unacceptable

Vibrations and impulse waves during transport PN-83/T-42106

www.pulsar.pl PSDC04122T

2. Installation.

2.1 Requirements.

The stabilized PSU is to be mounted by a qualified installer, holding relevant permits and licenses

(applicable and required for a given country) for 230V/AC interference and low-voltage installations. The unit

should be mounted in confined spaces, in accordance with the 2nd environmental class, with normal relative

humidity (RH=90% maximum, without condensation) and temperature from -10°C to +50°C. The PSU shall wor k in

a vertical position that guarantees sufficient convectional air-flow through ventilating holes of the enclosure.

During normal operation the total current consumption of the receivers cannot exceed

I=2A

As the PSU module is designed for a continuous operation and is not equipped with a power-switch,

therefore an appropriate overload protection shall be guaranteed in the power supply circuit. Moreover, the user

shall be informed about the method of unplugging (most frequently through separating and assigning an

appropriate fuse in the fuse-box). The electrical system shall follow valid standards and regulations.

2.2 Installation procedure.

1. Before installation, make sure that the voltage in the 230V power-supply circuit is cut off.

2. Mount the PSU in a selected location and connect the wires.

3. Connect the power cables (~230VAC) to L-N terminals of the PSU. Connect the ground wire to the terminal

marked by the earth symbol. Use a three-core cable (with a yellow and green PE protection wire ) to make the

connection. Lead the cables to the appropriate terminals of the connection board through the bushing.

The shock protection circuit shall be performed with a particular care, i.e. the yellow

and green wire coat of the power cable shall stick to one side of the terminal marked with the

‘ ’ earth symbol in the PSU enclosure. Operation of the power supply without a properly

made and fully operational shock protection circuit is UNACCEPTABLE! It can result in

device damage or an electric shock.

4. Connect the receivers’ cables to the AUX1…AUX4 connectors on the LB4 strips.

5. In electrical installations with significant voltage drops in the resistance of the wires that lead to the receivers, the

voltage value can be corrected with the P1 potentiometer (12,0V÷15,0V DC).

6. Check the PSU operating status indication

7. Once the installation and operation control have been completed, the enclosure can be locked.

3. Operating status indication.

The PSU is equipped with LED indication of operation status. The presence of power at the outputs of the

PSU is indicated by the illumination of green LEDs on the front panel of the device.

3.1. LED indication

•LED1…LED4 green diodes indicate power at the outputs:

LB4- AUX1…..AUX4.

In case of a power loss at the output (fuse activation), an appropriate diode goes out. (L1 for AUX1, L2 for

AUX2 etc.)

www.pulsar.pl PSDC04122T

4. Operation and use.

4.1 Overload or short circuit at the PSU output.

The AUX1 ÷ AUX4 PSU outputs of the LB4 strips are protected against a short circuit by glass fuses. If a fuse-

assisted protection has been chosen, replace the fuse (of the same parameters) in case of a failure.

4.2 Maintenance.

Any and all maintenance operations may be performed following the disconnection of the PSU from the

power supply network. The PSU does not require performing any specific maintenance measures. However, in

case of significant dust level, clean its interior with compressed air. In case of a fuse exchange, use the

replacement of the same parameters.

www.pulsar.pl PSDC04122T

WEEE MARKING

According to the EU WEE Directive – It is required not to dispose of electric or electronic w ste s

unsorted municip l w ste nd to collect such WEEE sep r tely.

GENERAL WARRANTY CONDITIONS

1. Pulsar K. Bogusz Sp.j. (the manufacturer) grants a one-year warranty for the equipment counted from the device’s production

date.

2. The warranty includes free-of-charge repair or replacement with an appropriate equivalent (the selection is at the

manufacturer’s discretion) if the malfunction is due to the manufacturer includes manufacturing or material defects unless such

defects have been reported within the warranty period (item 1).

3. The equipment subject to warranty is to be brought to the place where it was purchased or directly to the main office of the

manufacturer.

4. The warranty applies to complete equipment accompanied by a properly filled warranty claim with a description of the defect.

5. Should the claim be accepted the manufacturer is obliged to provide warranty repairs at the earliest convenience however not

later that within 14 days from the delivery to the service centre of the manufacturer.

6. The repair period mentioned in item 5 may be prolonged if there are no technical possibilities to carry out the repairs or if the

equipment has been conditionally accepted due to the breaking warranty terms by the claimant.

7. All the services rendered by force of the warranty are carried out at the service centre of the manufacturer exclusively.

8. The warranty does not cover the defects of the equipment resulting from:

- reasons beyond the manufacturer's control

- mechanical damage

- improper storage and transport

- use that violates the operation manual or equipment’s intended use

- fortuitous events including lightning discharges power failures fire flood high temperatures and chemical agents

- improper installation and configuration (in defiance with the manual)

9. The warranty is void in any of the following circumstances:

- construction changes

- repairs carried out by any unauthorized service center

- damage or removal of warranty labels

- modifications of the serial number

10. The liability of the manufacturer towards the buyer is limited to the value of the equipment determined according to the

wholesale prices suggested by the manufacturer on the day of purchase.

11. The manufacturer takes no responsibility for the defects that result from:

- the damaging malfunctioning or inability to operate the equipment

- defects that result from using the equipment outside its stated specifications and operating parameters failing to abide by the

recommendations and requirements contained in the manual or the use of the equipment.

Puls r K.Bogusz Sp.j.

Siedlec 150 32-744 Łapczyca Poland

Tel. (+48) 14-610-19-40 Fax. (+48) 14-610-19-50

e-mail: biuro@pulsar.pl sal[email protected]

http:// www.pulsar.pl www.zasilacze.pl

Inhaltsverzeichnis

Andere Pulsar Stromversorgung Handbücher

Pulsar

Pulsar GREY POWER plus AWZ 222 Bedienungsanleitung

Pulsar

Pulsar BLACK POWER PSBEN 10A12C Bedienungsanleitung

Pulsar

Pulsar PSBEN 10A12D/LCD Bedienungsanleitung

Pulsar

Pulsar PSB-24V10A Bedienungsanleitung

Pulsar

Pulsar HPSB 2512C Bedienungsanleitung

Pulsar

Pulsar HPSB 5524D Bedienungsanleitung

Pulsar

Pulsar POE0848C Bedienungsanleitung

Pulsar

Pulsar PSDC09125T Bedienungsanleitung

Pulsar

Pulsar 276V/7A/2x17Ah/LCD Bedienungsanleitung

Pulsar

Pulsar PSBS 5012D Bedienungsanleitung

Pulsar

Pulsar PSBEN 5012E Bedienungsanleitung

Pulsar

Pulsar EN54-5A17LCD Bedienungsanleitung

Pulsar

Pulsar RUPS824T Bedienungsanleitung

Pulsar

Pulsar AWZ 521 Bedienungsanleitung

Pulsar

Pulsar PSBOC501235 Bedienungsanleitung

Pulsar

Pulsar Blue Power PSBS 2012B Bedienungsanleitung

Pulsar

Pulsar Red Power Plus EN54C series Bedienungsanleitung

Pulsar

Pulsar PSBOC30012200 Bedienungsanleitung

Pulsar

Pulsar PSU-B-13.8V/S-10A/1/EL-TR-17Ah/MC Bedienungsanleitung

Pulsar

Pulsar HPSB 5524C Bedienungsanleitung

Pulsar

Pulsar PSBEN 3024C Bedienungsanleitung

Pulsar

Pulsar HPSBOC 5048C Bedienungsanleitung

Pulsar

Pulsar 276V/2A/2x17Ah/LCD Bedienungsanleitung

Pulsar

Pulsar PS20012140 Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung

Elmdene

Elmdene G1380xN-y-s Series Bedienungsanleitung