Pulsar USB-TTL INTU Bedienungsanleitung
Interface
USB-TTL
v.1.0
CODE: INTU
EN*
Edition: 6 from 27.11.2019
Supercedes edition: 5 from 25.01.2019
www.pulsar.pl INTU
2
CONTENTS
1. General description. ................................................................................................................................3
2. Installing the drivers................................................................................................................................4
3. Configuring the connection in the PowerSecurity program................................................................5
4. Technical parameters..............................................................................................................................6
www.pulsar.pl INTU
3
Features:
local connection of the power supply with the computer via USB
easy connection configuration
power from the USB port of the PC
cooperation with PowerSecurity program
optical indication
compact size
warranty –5 years from the production date
1. General description.
The USB-TTL „INTU” interface enables local connection of the PC with the power supply unit of the PSBEN
or EN54 series. The interface is recognized by the operating system as a virtual COM port. The connection does
not require any additional equipment.
Fig. 1. The USB-TTL interface.
The picture below shows the connection between the USB-TTL interface, the power supply and the PC.
Fig.2. The schematic diagram of the connection using the USB-TTL interface.
www.pulsar.pl INTU
4
2. Installing the drivers.
For proper operation, the USB-TTL interface requires the correct drivers installed on the PC.
When connected to a free USB port on the computer, the interface will be automatically detected by the
operating system and the drivers will be installed.
If the drivers have not been previously installed, you must download the appropriate instructions and
complete the installation in accordance with the guidelines. All instructions and drivers are available on the chipset
manufacturer's website at:
http://www.ftdichip.com/Support/Documents/InstallGuides.htm
Drivers to be installed can be downloaded at:
http://www.ftdichip.com/FTDrivers.htm
After installing the drivers, connect the USB-TTL into the USB port of your computer. An additional COM
port (e.g. COM5), configured with the interface and providing access to the PSU, will be displayed. The assigned
COM port can be checked in the Device Manager window (location: START > Control Panel > System > Hardware
> Device manager).
Fig. 3. The device manager window.
www.pulsar.pl INTU
5
3. Configuring the connection in the PowerSecurity program.
The “PowerSecurity” program can be downloaded at:
http://www.pulsar.pl/pliki/PowerSecurity.exe
1. Run the PowerSecurity program.
2. Choose the Power Supplies > New Power Supply option from the menu bar. The “Configuration of
connection” window, that allows configuring the settings, will be displayed. Enter the same settings as in
the picture below.
The power supply units of the EN54 series allow higher transmission speeds - instead of 19.2k 8E1 it
can be set to 115.2k 8E1. The changed values apply to all settings.
Fig. 4. The connection configuration window.
PSU
Description
Name
The name of the PSU
The name that should be assigned individually to each PSU.
Address
1 ÷ 247;
Enter the address assigned to the PSU in the RS485 bus
Refresh period of
the preview [ms]
100 ÷ 60 000ms;
Refresh period of the parameters in the preview window.
CONNECTION
Type
Modbus RTU
Port
Enter the COM port number the same as assigned in the device manager, or select
AUTO for automatic assignment.
Transmission
speed
Max 19 200 bauds –PSU of the PSBEN series
Max 115 200 bauds –PSU of the EN54 series
Parity check
Parity
Response time [ms]
100 ÷ 60 000ms;
The response time from the power supply
The interval
between the
transmissions [ms]
The minimal interval between transmissions.
The number of
retransmissions
The number of retransmissions after which the program reports a connection error.
www.pulsar.pl INTU
6
3. After loading the connection configuration, the ”Preview” tab will be displayed. Press the icon in the
upper left corner to connect the power supply. Once the connection is established, the current parameters
of the power supply, automatically updated according to the refresh cycle set during configuration, will be
displayed.
Fig. 5. The preview window of the PSU of the PSBEN (left) and EN54 series (right).
More information on the "PowerSecurity" program can be found in the manual which can be downloaded
at: http://www.pulsar.pl/pl/opisy/PowerSecurity.pdf
4. Technical parameters.
Power supply
5 V DC from the USB port of the PC
Current consumption
Max. 25mA from the USB port of the PC
Transmission speed
Max. 115200 bauds, with parity check
Optical indication
PWR –supply voltage indication (Red LED)
Compatibility of the USB interface
USB 1.1
USB 2.0 (Full Speed)
Power cable length
1.5 m
USB cable length
1,7m
Protection class
IP20
Operating conditions
Temperature -10 oC ÷ 40 oC
Relative humidity 20%...90%
Dimensions (LxWxH)
57 x 32 x 25 [mm]
Net/gross weight
0,13kg / 0,18kg
Storage temperature
-20ºC...+60ºC
Pulsar sp. j.
Siedlec 150, 32-744 Łapczyca, Poland
Phone (+48) 14-610-19-40, Fax. (+48) 14-610-19-50
http:// www.pulsar.pl, www.zasilacze.pl
WEEE LABEL
Waste electrical and electronic equipment must not be disposed of with normal household waste. According to the European Union
WEEE Directive, waste electrical and electronic equipment should be disposed of separately from normal household waste.
Inhaltsverzeichnis
Andere Pulsar USB-Schnittstelle Handbücher
Beliebte USB-Schnittstelle Handbücher anderer Marken
PASCO
PASCO SCIENCEWORKSHOP 750 Bedienungsanleitung
Phonic
Phonic FIREFLY 302 USB Bedienungsanleitung
OHAUS
OHAUS Scout STX Series Bedienungsanleitung
Denon
Denon DN-HC4500 - DJ Mixer USB Controller Bedienungsanleitung
Lutron Electronics
Lutron Electronics Stanza SZ-CI-USB-CPN5138 Bedienungsanleitung
Paradox
Paradox PMC5-TI00 Bedienungsanleitung
Thorsis Technologies
Thorsis Technologies isDNet USB Bedienungsanleitung
Thorsis Technologies
Thorsis Technologies isHRT USB Bedienungsanleitung
microHAM
microHAM DigiKeyer Bedienungsanleitung
Apogee
Apogee Jam X Bedienungsanleitung
RigExpert
RigExpert TI-3000 Bedienungsanleitung
microHAM
microHAM USB Interface II Bedienungsanleitung