PureStorage FlashArray //X R2 Bedienungsanleitung

FlashArray Quick Installation Guide

Before You Begin

Recommended clearance for the front (cold aisle) is 91.5 cm

(36 in.). The minimum requirement is 81.5 cm (32 in.).

Recommended clearance for the rear (hot aisle) is 91.5 cm

(36 in.). The minimum requirement is 61 cm (24 in.).

No special clearance is required on top, bottom, or sides.

Recommended clearance for rack posts is 74 cm (29 in.) (the

default on most racks). Minimum is 61 cm (24 in.), Maximum

is 81.25 cm (32 in.).

Document Conventions

Symbol Meaning

Potential for injury, physical damage, or loss of data

or array configuration information

Supplementary instruction

Best practice

For your information

Safety and Handling

Before you install the FlashArray, refer to FlashArray

Safety and Compliance.

Contacting Customer Support

For assistance, contact Pure Storage Support. You can

reach Support the following ways:

lVisit https://support.purestorage.com

lEmail support@purestorage.com

lCall (800) 379-7873 in the U.S. For international sup-

port, see https://support.purestorage.com

Support is available 24 hours a day, seven days a week.

Estimated Installation Time

You should be able to install the FlashArray in approximately

one hour and 15 minutes.

Preparing for Installation

The FlashArray chassis weighs 37.8 kg (83.2 lbs.),

DirectFlash Shelves weigh 39.8 kg (85.8 lbs.), and

expansion shelves weigh 20 kg (44 lbs.) each. Make

arrangements for safe lifting during installation.

Make sure you install DirectFlash Modules, Flash Mod-

ules, or blanks after rack mounting each chassis. The

FlashArray chassis with modules installed weighs

43.2 kg (95.2 lbs.).

Make sure that the rack can support the total weight of all

installed equipment including cables and rails (approx-

imately 48.5 kg or 107 lbs.), and that the total weight is

within the floor loading limit.

Have all necessary Fibre Channel and Ethernet cables

(not supplied by Pure Storage) available.

Verify that front and rear rack mounting posts are

between 61 and 91 cm (24-36 in.) apart, and that you

have 3 RU (13.3 cm or 5.25 in.) of vertical rack space for

the FlashArray chassis and 2 RU (8.9 cm or 3.5 in.) for

each expansion shelf.

Verify that the installation environment

lIs within the operating temperature range of 5-35°C.

lDoes not have airflow ducts aimed directly at any

FlashArray chassis, controller, or shelf.

Have a local console (VGA monitor and USB keyboard

or a computer with terminal emulation capability) avail-

able in case it is required for software configuration or

diagnosis.

Make sure that cable lengths are adequate by mounting

the chassis and shelves in a contiguous stack as shown

in the DirectFlash Shelf, Expansion Shelf, and Add-on

Shelf Quick Installation Guides.

Before unpacking, inspect packages for shipping dam-

age. If damage is present, photograph it and contact

Pure Storage Technical Support before proceeding.

Save cartons and packing material in case return ship-

ment to Pure Storage is necessary.

Save all tools in FlashArray kit.

1. Unpack the FlashArray

Verify that the FlashArray package contains the items shown in Figure 1.

Figure 1. Unpacking the FlashArray

If storage shelves are included, refer to the DirectFlash Shelf Quick Installation Guide,Expansion Shelf Quick Installation

Guide, or Add-on Shelf Quick Installation Guide (in the "Open Me First" box) for the list of contents in the shelf package.

40-0154-01 Page 1 of 6

Planning the Installation

Mount heavier equipment lower in the rack. A fully loaded FlashArray chassis weighs 43.2 kg (95.2 lbs.). If possible, install

the chassis below other devices in the rack.

2. Install the Rails

1. (Square-hole racks only) Install the #10-32 cage nuts (from

the Accessory Kit) on the front of the rack, as shown in Fig-

ure 2.

On round-hole racks, use clip nuts (not provided by Pure

Storage, Inc.) instead of cage nuts.

The FlashArray includes two rails, labeled right and left.

The rails have locating pins (for square- and round-hole

racks) or positioning studs (visible if you unscrew and

remove the locating pins for threaded-hole racks) that you

align with the holes in the rack.

2. Install one of the two rails (the installation order does not

matter) by pulling the spring-loaded lever back and inserting

the locating pins or positioning studs in the front mounting

post at the desired height. Release the lever once the rail is

in place. See Figure 3.

3. Extend the rear of the rail until the locating pins or pos-

itioning studs reach the rear mounting post, and press the

rail into the rear post until the latch engages. See Figure 4

(left rail shown).

Install the rear screws only. Front screws are installed later.

4. (All rack types) Secure the rear of each rail to the rack with

the screws provided in the Accessory Kit. One screw is

provided for the rear of each rail. Use the second or fifth

hole up from the bottom of each rail (shown going into the

fifth hole on Figure 4).

5. Repeat 1–4 above to install the second rail.

Make sure to install the rear of each rail into the post holes

that are at the same height as the holes being used on the

front post. Otherwise, the chassis might slide off the rails

causing personal injury and damage to the FlashArray.

Figure 2. Installing Cage Nuts

Figure 3. Installing a Rail (Front Post)

Figure 4. Installing a Rail (Rear Post)

3. Mount the Chassis in the Rack

The FlashArray chassis weighs 37.8 kg (83.2 lbs.) before you install DirectFlash Modules or blanks. Make arrangements

for safe lifting during installation. Pure Storage recommends two people for this procedure.

1. Remove the chassis from the antistatic bag. With one person on each side, lift the chassis by the handles and slide it onto

the rails until the rear handles are two inches from touching the rack.

2. Support the front of the chassis while resting the rear on the rails, and remove each rear handle. See von Figure 5.

Figure 5. Mounting Chassis in Rack

FlashArray Quick Installation Guide

40-0154-01 Page 2 of 6 October 12, 2018

3. Mount the Chassis in the Rack (Cont'd)

3. Continue to slide the chassis on the rails until the front

handles are two inches from touching the rack.

Continue to support the front of the chassis as you

remove the front handles. See won Figure 5.

4. Slide the chassis completely into the rack so that the

chassis ears are flush with the front of the rack and the

slam latches lock into place. See Figure 6.

5. (Square- and round-hole racks only) Secure the front of

each rail to the rack and chassis with the screws

provided in the Accessory Kit. One screw is provided for

each rail.

To install the screws, open both slam latches on the

chassis front panel and thread the screws through each

slam latch hole. Tighten the screws, securing the chassis

to the rack and the attached cage nut (installed in step of

"Install the Rails" on the previous page) or clip nut (for

use with round-hole racks and not provided by Pure Stor-

age), and then close the slam latches. See Figure 7.

(Threaded-hole racks only) Secure the front of each rail

to the rack with screws that fit the rack's threaded holes.

For example, if the rack has #10-32 threads, you can use

the screws provided in the Accessory Kit. If the rack has

threads of another size, you must obtain matching

screws.

Figure 6. Mounted Chassis

Figure 7. Securing Front of Rail

4. Install DirectFlash Modules, Flash Modules, or Blanks

Install DirectFlash Modules, Flash Modules, or blanks in groups of 10. Do not alternate module types. DirectFlash Module

and Flash Module labels show the capacity in terabytes (see Figure 8).

Make sure all unused slots are filled with blanks.

1. Install DirectFlash Modules, Flash Modules, or blanks (10 or 20) into the chassis slots from left to right, starting with slot 0.

2. Make sure that DirectFlash Module, Flash Module, or blank front panels are flush with the FlashArray front panel. Check

that the latch on each module has engaged by pulling gently on it until you feel resistance.

Figure 8. Installing DirectFlash Modules

FlashArray Quick Installation Guide

40-0154-01 Page 3 of 6 October 12, 2018

5. Connect Host, Replication, and Management Cables

Connect each controller (CT0 and CT1) to a separate storage area network (SAN) and replication fabrics (A and B in

Figure 9) to ensure redundancy.

Depending on the customer order, the quad-port mezzanine can be equipped with either an Ethernet or SAS card,

and the PCIe slots can be equipped with Fibre-Channel or Ethernet cards.

1. Use customer-supplied cables to connect host ports FC0 through FC13 or ETH4 through ETH5 and ETH10 through

ETH17 (labeled SAN in Figure 9) to SANs as directed by the customer. Leave unused ports unpopulated.

2. Connect customer-supplied 1-GbE cables to management ports ETH0 and ETH1. Alternatively, you can use ETH1 for

1-GbE replication.

3. Connect customer-supplied 10- or 25-GbE cables from ports ETH2 and ETH3 (labeled REPL A and REPL B in Fig-

ure 9) to replication network switch ports.

4. If the controller has an Ethernet card in the quad-port mezzanine, you can connect ETH6 through ETH9 to DirectFlash

shelves. See the DirectFlash Shelf Quick Installation Guide for more information.

If the controller has a SAS card in the quad-port mezzanine, you can connect SAS0 through SAS3 to expansion

shelves. See the Expansion Shelf Quick Installation Guide for more information.

5. After connecting, pull gently on the cables until you feel resistance to ensure they are secure.

Repeat steps 1–5 for the second controller.

Figure 9. FlashArray Controller Ports (QP ETH and FC PCIe Cards Shown)

6. Unpack and Install Shelves

Unpack and install any DirectFlash shelves or expansion shelves. Refer to the DirectFlash Shelf Quick Installation Guide (for

DirectFlash shelves) or Expansion Shelf Quick Installation Guide (for 12G shelves) for unpacking, installation, and cabling

instructions. After installing DirectFlash shelves or expansion shelves, resume the installation procedure starting with "Install

the Bezel" below.

7. Install the Bezel

1. Remove the protective film on the front surface of the bezel.

2. Install the bezel, aligning the power connector with the logo illumination socket on the front panel. See Figure 10.

Make sure the asset tag is fully inserted into the slot or you will be unable to install the bezel.

To remove the bezel, press the two fastening handles to disengage it from the front panel.

Figure 10. Installing the Bezel

FlashArray Quick Installation Guide

40-0154-01 Page 4 of 6 October 12, 2018

8. Power on the Array

Connecting the Power Supplies

1. Power on DirectFlash shelves or expansion shelves (if installed), start-

ing with the lowest ID number and proceeding to the highest, as

described in the DirectFlash Shelf Quick Installation Guide, Expansion

Shelf Quick Installation Guide, or Add-on Shelf Quick Installation Guide.

2. Power on FlashArray PS0 and PS1 as follows (Figure 11 shows PS0):

lLower the power supply handle, make a loop in the power cord near

the plug, and wrap the captive strap around the loop, securing the cord

to the handle.

lInsert the power plug in the power supply socket.

Securing the captive strap helps prevent accidental power dis-

connections.

3. Connect the PS0 power cord to the AC power distribution unit. After you

connect the power, the controller LEDs illuminate and the controller fans

start.

4. Connect the PS1 power cord to a separate AC power distribution unit to

ensure redundancy.

Figure 11. Securing the Power Cord

After Powering On

As each power supply comes online, the system fans run high for a moment, and then run more quietly. Once the system is

powered on, the LEDs illuminate. See Table 1 for front-panel LED descriptions and Table 2 for rear-panel LED descrip-

tions.

Table 1. Front-Panel LEDs

LED Description

Power Supply Unit (PS) Green if OK. Amber if faulty.

Controllers (CT) Green if OK.

System OK Green if OK. Off if any system

components are faulty.

System Fault Off if OK. Amber if any system

components are faulty.

System ID Off.

Table 2. Rear-Panel LEDs

LED Description

OK Green if OK. Amber if faulty.

PWR Green if OK. Amber if power fault

occurs.

ID Off.

Port LEDs Shows link state when controller is

active.

9. Sign into FlashArray and Configure Controllers

Prerequisites

lA completed Pre-Installation Checklist from the customer. The checklist contains important configuration details.

lA USB Flash drive with the correct version of Purity for the customer.

lRoot or puresetup credentials. See Array Install: Changing Purity Version on a Fresh Array for more information.

Log into the FlashArray

Use the KVM cable from the Accessory Kit to connect the CT0 KVM port (see Figure 9 for the port location) to a local console.

The KVM cable has one serial, one VGA, and two USB ports. Use a VGA monitor and USB keyboard or a computer (e.g., a

laptop) equipped with a serial-to-USB converter and terminal emulation software as a local console. The terminal settings for

the serial port are 8-N-1 (8 data bits, no parity, 1 stop bit), Xon/Xoff flow control, 115,200 baud. After connecting the KVM cable,

press any key to start the console.

Configure the Controllers

1. Log into CT0 as root or puresetup and enter the pureversion command to determine the Purity version.

2. If you need to upgrade Purity, do the following:

lEnter the ls /dev/sd* -lrt command to get the partition number of the USB Flash drive with the Purity ppkg.

Mount to FlashArray by entering mount /dev/sd# /mnt where # is the USB drive partition number.

lCopy the ppkg and sha1 to the FlashArray (e.g., enter cp /mnt/purity* /home/puresetup).

lGo to the installation directory (cd /home/puresetup) and run the installation command

(pureinstall purity-*.ppkg), and then follow the on-screen instructions.

3. Connect the KVM cable to CT1, log in as root or puresetup, and repeat steps 1–2.

4. Connect the KVM cable to CT0, log in as root or puresetup, and enter the puresetup newarray command to set up

the array.

If network connectivity is unavailable, unplug the Ethernet cable. Otherwise tests might take 15 minutes to time out.

Use the completed Pre-Installation Checklist to enter the customer environment variables.

The FlashArray tests Remote Assist, phone home, and time syncs with NTP.

If any tests fail, check for typos, and make any necessary changes to the networking and firewall configuration.

Change the time zone, if necessary. Reboot if prompted to do so.

5. Connect the KVM cable to CT1 and enter the puresetup secondary command, using the information from the Pre-

Installation Checklist.

If network connectivity is unavailable, unplug the Ethernet cable. Otherwise tests might take 15 minutes to time out.

If any tests fail, check for typos, and make any necessary changes to the networking and firewall configuration.

Change the time zone, if necessary. Reboot if prompted to do so.

FlashArray Quick Installation Guide

40-0154-01 Page 5 of 6 October 12, 2018

9. Sign into FlashArray and Configure Controllers (Cont'd)

Verify Setup and Configuration

After the FlashArray is online, make sure it is healthy by doing the following:

1. Enter the purehw list command. All statuses should read ok.

2. Enter the hardware_check.py command. All results should be All's well.

3. Enter the pureboot list command. Make sure that *--> is pointing at the desired version.

4. Enter the purearray list --controller command. Make sure both controllers are online and running the cor-

rect version of Purity.

5. Test the Purity GUI by viewing the virtual IP (VIP) in a browser.

6. Test the Purity CLI by using ssh pureuser@array_VIP.

7. If the array has one or more DirectFlash shelves or expansion shelves, enter the following commands on each con-

troller to check the SAS connections:

storage_view.py config

storage_view.py enclosures

If the SAS cables are connected correctly, these commands return the following response:

No errors detected.

If errors are detected, contact Pure Storage Technical Support for assistance.

To disable root and puresetup users, enter the purearray enable console-lock command. To re-enable

these users, enter the purearray disable console-lock command.

Configure Pure1

Refer to the software documentation at the Pure Storage Community site for more information.

U.S. and other countries. Other company, product, or service names may be trademarks or service marks of their respective owners.

The Pure Storage products described in this documentation are distributed under a license agreement restricting the use, copying, distribution, and decom-

pilation/reverse engineering of the products. The Pure Storage products described in this documentation may only be used in accordance with the terms of the license

agreement. No part of this documentation may be reproduced in any form by any means without prior written authorization from Pure Storage, Inc. and its licensors, if

any. Pure Storage may make improvements and/or changes in the Pure Storage products and/or the programs described in this documentation at any time without

notice.