Purkeys DIRECT FLEX Einrichtungshandbuch
DIRECT FLEX/MAX
DIAGNOSTIC GUIDE
300-51 R1.00
1
P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net
CONTENTS
Direct Flex (no severe service cables)..............................................................2
Direct Max (includes severe service cables) ...................................................3
Cover Assembly..................................................................................................4
Interior Light Module (optional) .....................................................................5
Connections Inside Nosebox ..................................................................5
Connections Outside Nosebox ...............................................................6
Basic Troubleshooting .......................................................................................7
No Lights on Face of the Nosebox..........................................................7
Batteries Not Being Charged ...................................................................9
Interior Lights Not Working (if installed) ...........................................15
Limited Commercial Warranty Policy...........................................................17
2
DIRECT FLEX
(NO SEVERE SERVICE CABLES)
3
P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net
FLEX/MAX DIAGNOSTIC GUIDE
DIRECT MAX
(INCLUDES SEVERE SERVICE CABLES)
4
COVER ASSEMBLY
5
P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net
FLEX/MAX DIAGNOSTIC GUIDE
INTERIOR LIGHT MODULE (OPTIONAL)
CONNECTIONS INSIDE NOSEBOX
6
CONNECTIONS OUTSIDE NOSEBOX
7
P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net
FLEX/MAX DIAGNOSTIC GUIDE
NO LIGHTS ON FACE OF THE NOSEBOX
Step 1: Conrm all connections are tight and inspect wiring for defects.
Step 2: Connect the tractor to the unit.
Step 3: Start the tractor.
Step 4: Check the 2 amp fuse on the
DC/DC converter in the battery
box:
• If blown, replace.
• If good, proceed.
Step 5: Using a voltmeter, measure
the voltage at the 2-pin terminal
strip on the DC/DC converter
charging plate:
• Place the positive lead on the
ligate battery+ stud.
• Place the negative lead on the
ground stud.
• If there is a battery voltage
reading, skip to step 7.
• If no voltage is shown, proceed
to step 6.
BASIC TROUBLESHOOTING
NOTE: Battery voltage below 7 volts will NOT power the system.
8
Step 6: Check the 30 amp circuit
breaker using a voltmeter:
• Place the positive lead on
the circuit breaker stud that
connects to the red junction
stud closest to the DC/DC
converter on the plate.
• Place the negative lead on the
negative post of the battery.
• If there is a battery voltage
reading, proceed to the next
step.
• If no voltage is shown, reset the
circuit breaker.
• If there is still no voltage, check
wiring for defects.
• If no defects are found, replace
the circuit breaker.
Step 7: On the front of the trailer,
remove the hardware holding the
cover assembly to the nosebox
base.
• Place the voltmeter positive
lead where the orange wire is
connected.
• Place the negative lead where
the white wire is connected.
• Check the battery voltage
reading.
• If there is a battery voltage
reading, replace the faceplate
assembly.
• If there is no voltage reading,
inspect the wiring for defects
and repair any issues.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Purkeys Akkuladegerät Handbücher
Purkeys
Purkeys SOLAR BOLT Bedienungsanleitung
Purkeys
Purkeys BOSS-01 Bedienungsanleitung
Purkeys
Purkeys Select P1020-K Bedienungsanleitung
Purkeys
Purkeys DIRECT PLUS Bedienungsanleitung
Purkeys
Purkeys SELECT Einrichtungshandbuch
Purkeys
Purkeys Liftgate Double Check Bedienungsanleitung
Purkeys
Purkeys DIRECT PLUS Einrichtungshandbuch
Purkeys
Purkeys SELECT Bedienungsanleitung
Purkeys
Purkeys DIRECT Einrichtungshandbuch
Purkeys
Purkeys SOLAR BOLT Bedienungsanleitung
