Purmo V10 Bedienungsanleitung

Purmo Group, Gateshead, NE11 0PG; Purmo Group Newcastle West, V42 TD39

DSVI-001

Safety Precaution:

Radiators are hot when in use, and as such, present a risk of

burns to users on prolonged contact.

The temperature of a radiator is dependent on the temperature

of the system water, as set by the system installer or end user.

Installers and users should ensure that those who come in to

close proximity to hot radiators are aware of the risks of burns.

Installers and users should take all necessary steps to minimise

the risk of burns. If the risk is signiﬁcant, consideration should

be given to installing low temperature radiators, or to placing

guards in front of radiators.

For the correct installation of radiators it is essential that the

ﬁxing of the radiator is carried out in such a way that it is

suitable for intended use AND predictable misuse.

A number of elements need to be taken into consideration

including ﬁxing method used to secure the radiator to the wall,

the type and condition of the wall itself, and any additional

potential forces or weights, prior to ﬁnalising installation.

IN ALL CASES IT IS STRONGLY RECOMMENDED THAT A

SUITABLY QUALIFIED PROFESSIONAL INSTALLER OR SIMILAR

TRADESPERSON CARRIES OUT THE INSTALLATION.

PLEASE NOTE: The ﬁxing materials provided are only intended

for installation on walls made of solid wood, bricks, concrete

or on timber frame stud walls where the ﬁxing is in to the

timber. All walls being considered should have no more than

a maximum of 3 mm wall ﬁnishing. For walls made of other

materials, for example hollow bricks, please consult your installer

or specialist supplier. ONCE AGAIN, IF YOU ARE UNSURE, IT

IS STRONGLY RECOMMENDED THAT A SUITABLY QUALIFIED

PROFESSIONAL INSTALLER OR SIMILAR TRADESPERSON

CARRIES OUT THE INSTALLATION.

PENCIL MARKS

RADIATOR

LENGTH

RIGHT HAND

LEFT HAND

HEIGHT : 600mm TO 1900mm

88 88

200

ALL RADIATOR LENGTHS

HEIGHT : 2000mm TO 3000mm

88 88

200

200 ==

ALL RADIATOR LENGTHS

THGIEH

LENGTH

HTGNEL / 2

821

272

V10: 100mm

DIMENSION A

V20: 88mm

RADIATOR WALL LOCATION

FIG 1.

MOUNTING LUG LOCATIONS

FIG 2.

Vertical Flat Tube Radiator

Models: V10 & V20

Installation Procedure:

1. Decide on the position of the radiator and mark the

mounting bracket positions according to Fig 1.

2. Align the wall brackets according to Fig 3 and mark the

hole ﬁxing hole positions.

3. Drill and plug the bracket ﬁxing holes and ﬁx the brackets

securely to the wall.

4. Mount the radiator on the brackets and connect the

radiator to the heating system.

5. Fit the plugs and vent to the radiator.

6. Fill the system and vent the radiator.

7. Balance the system to ensure correct ﬂow through all

radiators.

MOUNTING BRACKET DETAILS

FIG 3.

Purmo Group, Gateshead, NE11 0PG; Purmo Group Newcastle West, V42 TD39

Vertical Flat Tube Radiator

Models: V10 & V20

BRACKET MOUNTING AND

PIPE CENTRE DETAILS

CONNECTION DETAILS

CONNECTION LADDER

BAFFLE LOCATED IN

CENTRE OF HEADER

BETWEEN FLOW AND

RETURN

(INDICATED BY STICKER)

BAFFLE

LOCATION STICKER

BRACKET

LN2 WALL

SIDE VIEW V10

78 21

BRACKET

A2 WALL

SIDE VIEW V20

PLAN VIEW V10

PLAN VIEW V20

E F

G H

Notes:

Radiator should be connected BOE(BD/DB) or

BBOE (EF/FE)

For TTOE or TOE the radiator must be inverted.

The header containing the bafﬂe (depicted by

the bafﬂe sticker), must always be ﬁtted ﬂow/

return.

Information for the installer:

These radiators are for use on two pipe pumped indirect

domestic and commercial heating installations, with a maximum

working temperature of 100°C.

The system should be designed in accordance with BS EN

12828:2012+A1:2-14 or BS EN 12831-1:2017 as appropriate,

with particular care to avoid air entry or water discharge.

The installation work must be carried out in accordance with

recognised good practice, and precautions taken to avoid

contamination which could lead to corrosion. In accordance

with current Building Regulations a corrosion inhibitor or other

suitable water treatment must be used. The manufacturer’s

instructions must be strictly followed.

Failure to comply with these standards might invalidate the

manufacture’s warranty.

10 Year warranty.

The recommendations of BS 7593, Code of Practice for

treatment of water in domestic hot water central heating

systems, should be followed where appropriate.

Important Notes:

• The header with the ﬂow/return connections contains a

bafﬂe and is identiﬁed by a sticker (shown on the right).

• Connections in the opposite header are to be used as vents

or drains depending on the orientation of the radiator.

• Ensure there is no trapped air in the radiator by adequately

bleeding the system during installation.

• Flow rate may need to be adjusted/balanced for optimum

performance.

PLAN VIEW V20

2020

SIDE VIEW V20

100 Min

PLAN VIEW V10

2020

SIDE VIEW V10

100 Min

DSVI-001

Moretti (UK) Ltd , Trade House, Yeovil BA22 8RT

Product Warranty

Thank you for purchasing a Moretti Design Radiator. Your radiator has been designed and tested to

give you many years of trouble-free service. For your additional peace of mind, we give the following

Warranty across the below design radiators. Your statutory rights are not affected by this Warranty.

•Moretti Modena

•Moretti Rovingo

•Moretti Sorrento

•Moretti Tuba

Subject as provided below. Moretti Radiators underwritten by Moretti (UK) Ltd (“Moretti ”) warrants to

the original purchaser at the original installation site that its products will be free from defects in materials

and workmanship for the period of 5 (FIVE) years*.

*12 months on any panel products placed in an area of high humidity

The original purchaser’s remedy for breach of this Warranty is expressly limited to repair or replacement

of any part or parts found to be defective under conditions of normal service and use during the above

Warranty period and does not extend to Moretti being liable for any incidental, special or consequential

damages or losses whatsoever. Such as loss of use of the product, inconvenience or lost profits.

This Warranty does not cover any defect, damage or malfunction in the product which is due to; failure

to comply in any respect with Moretti’s installation, maintenance or operating instructions; faulty storage,

handling, installation or repair; mis-use; neglect; accident; abuse; or general wear and tear.

The system should be designed in accordance with BS EN 12828:2012 and BS EN 12831:2017, and

installed and commissioned in accordance with BS EN 14336:2004. On completion of the installation

the system should be properly flushed and filled in accordance with the British Code of Practice for the

preparation, commissioning and maintenance of domestic central heating and cooling systems. We

strongly recommend the use of corrosion inhibitor for all applications.

Before free service under this Warranty can be provided, the original purchaser will be required to prove

the date of purchase and may be required to provide Moretti with supporting information, as Moretti

may need to conduct its investigation into the alleged defect.

Moretti reserves the right to make reasonable charge for inspection and testing any product which is

subject to a Warranty claim and the rights conferred by the Warranty are conditional upon the payment

of such charge. The charge may be made at Moretti’s discretion, either before or after the inspection

and testing of the product. In the event that it is established to Moretti’s reasonable satisfaction that a

valid Warranty claim has been made in respect of the product, then charge which has been paid will be

refunded in full by Moretti.

Dieses Handbuch passt für folgende Modelle

Andere Purmo Heizung Handbücher

Purmo

Purmo BR222 Bedienungsanleitung

Purmo

Purmo KABA Bedienungsanleitung

Purmo

Purmo FLORES E Wartungs- und Serviceanleitung

Purmo

Purmo YALI DIGITAL Bedienungsanleitung

Purmo

Purmo COMPACT VENTIL PLINTH Bedienungsanleitung

Purmo

Purmo H10 Bedienungsanleitung

Purmo

Purmo INSPIRATION - Bedienungsanleitung

Purmo

Purmo Squara Bedienungsanleitung

Purmo

Purmo RADSON APOLIMA Wartungs- und Serviceanleitung

Purmo

Purmo JARL 10 05 230 03 2 W Bedienungsanleitung

Purmo

Purmo DION Twin-M Bedienungsanleitung

Purmo

Purmo RADSON ELATO Wartungs- und Serviceanleitung

Purmo

Purmo PARADA PLINTH Bedienungsanleitung

Purmo

Purmo RADSON JAVA Wartungs- und Serviceanleitung

Purmo

Purmo CAMPAIGN Bedienungsanleitung

Purmo

Purmo RADSON EVIA Wartungs- und Serviceanleitung

Purmo

Purmo ULOW-E2V Bedienungsanleitung

Purmo

Purmo MCW-V Bedienungsanleitung

Purmo

Purmo BH 300 Bedienungsanleitung

Purmo

Purmo RAMO PLINTH Bedienungsanleitung

Purmo

Purmo OPTIMO 500E ECO Montageanleitung

Purmo

Purmo KABA2 Bedienungsanleitung

Purmo

Purmo RADSON MINORCA Wartungs- und Serviceanleitung

Purmo

Purmo TECHNICAL POCKET BOOK - Bedienungsanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

IRSAP

IRSAP The Radiator Company Ovali Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung