PXM Driver LED 1x2A/48V Bedienungsanleitung

MANUAL

Driver LED

1x2A/48V

PX319

TABLE OF CONTENTS

tel.: 12 626 46 92

fax: 12 626 46 94

E-mail: [email protected]

Internet: www.pxm.pl

Ver. 1.2

Manufacturer reserves the right to make modifications in order to improve device operation.

PXM Marek Żupnik spółka komandytowa

Podłęże 654

32-003 Podłęże

1. General description.............................................................................................

2. Safety conditions.................................................................................................

3. Connections and control elements description....................................................

4. DMX indicator light meanings..............................................................................

5. DMX address setting...........................................................................................

5.1 Smooth function settings.....................................................................

5.2. No Signal function settings................................................................

5.3. PWM frequency settings....................................................................

6. Driver output current setting................................................................................

6.1Temperature control.............................................................................

7. Connection diagram............................................................................................

8. Technical drawing................................................................................................

9. Technical data.....................................................................................................

Declaration of conformity.........................................................................................

The PX319 driver is designed to control LEDs. It has voltage of 12 - 48 V DC and a maximum

current-carrying capacity of 2 A. It is possible to set the driver output current according to the

parameters of receivers LED.

PX319 can be controlled by the DMX signal (the device has a built-in DMX-512 receiver) or it can

work independently. DMX address is set manually via a DIP switch on the housing. The user also

has the ability to set one of the eight levels of brightness with which the LEDs will be triggered in

the absence of a DMX signal.

1. GENERAL DESCRIPTION

2. SAFETY CONDITIONS

PX319 is a device powered with safe voltage of 12 - 48 V DC; however, you should at all times

obey the safety conditions. It is necessary to observe the following rules:

1. The device can be connected to 12 - 48 V DC (stabilised voltage) with current-carrying capacity

compatible with technical data.

2. All the conductors should be protected against mechanical and thermal damage.

3. In case of damage to a conductor, it should be replaced with a conductor of the same technical

parameters.

4. Connection of DMX signal can be made with a shielded conductor only.

5. All repairs, connecting and disconnecting of cables can only be made with cut off power supply.

6. The device should be strictly protected against contact with water and other liquids.

7. All sudden shocks, particularly dropping, should be avoided.

8. The device cannot be turned on in places with humidity exceeding 90%.

9. The device cannot be used in places with temperature lower than +2°C or higher than +40°C.

10. Clean with damp cloth only.

3. DESCRIPTION OF THE JOINTS AND CONTROLS

DMX address

switch

power supply

DMX signal LED

output to linear

LED modules

DMX IN

DMX OUT

resistor input limiting

the output current

temperature

sensor input

4. DMX INDICATOR LIGHT MEANINGS

The driver is equipped with one indicator light:

Status

Function

the diode is emitting

constant light

“No Signal” mode operation, the driver is

not receiving any DMX signal

the diode is blinking

a DMX signal is being received

“No signal” and PWM frequency

mode switch

5. DMX ADDRESS SETTING

254

255

256

509

510

511

PX319 allows for setting the address DMX. The address is set in a binary code using the “DIP

switch”. Below are some examples of setting the address DMX. Nine first “DIP switches” are

responsible for the address; the tenth switch is responsible for activating the “smooth” function.

2 3 4 5 6 7 8 9

ON DIP

2 3 4 5 6 7 8 9

ON DIP

2 3 4 5 6 7 8 9

ON DIP

2 3 4 5 6 7 8 9

ON DIP

1 10

2 3 4 5 6 7 8 9

ON DIP

1 10

2 3 4 5 6 7 8 9

ON DIP

1 10

2 3 4 5 6 7 8 9

ON DIP

2 3 4 5 6 7 8 9

ON DIP

1 10

2 3 4 5 6 7 8 9

ON DIP

1 10

9 10 Off

The white colour is a switch. It is ON when set in

the upper position, and OFF when set in the lower

position.

The PX319 driver is equipped with an additional DIP-Switch which allows you to set the No Signal

function, responding to the driver action when it does not receive the DMX signal.

With this switch, it is possible to set one of 4 brightness levels. The brightness increases from the

smallest (zero) to the maximum one, in accordance with the binary markings on the “DIP switch”.

Below are brightness levels and the corresponding switch settings.

2 3 4 5 6 7 8 9

ON DIP

1 10

With the smooth function enabled, transitions between successive control signal values are

smoothed, allowing for smooth changes in the brightness of the connected LEDs. This prevents

the light “vibration” effect that usually occurs in lighting systems when light intensity is being

changed.

The “smooth” function and DMX address set to 1.

5.1. SMOOTH FUNCTION SETTINGS

5.2. NO SIGNAL FUNCTION SETTINGS

2 3

Zero brightness level

1 brightness level

2 brightness level

3 brightness level

5.3. PWM FREQUENCY SETTINGS

You can set PWM frequencies using individual switch position no. 3 on the DIP switch:

2 3

Zero brightness level and PWM frequency of 366 Hz

2 3

Zero brightness level and PWM frequency of >20 kHz

Current limit

Resistor

250 mA

100R

300 mA

270R

350 mA

470R

400 mA

680R

500 mA

910R

600 mA

1k2

700 mA

1k5

750 mA

1k8

800 mA

2k2

900 mA

2k4

1000 mA

1050 mA

3k3

1100 mA

3k9

1250 mA

4k7

1300 mA

5k1

1400 mA

6k2

1500 mA

7k5

1600 mA

8k2

1750 mA

10k

1800 mA

12k

2000 mA

15k

The PX319 driver is equipped with a function to set the output current controlling linear LED

modules. Depending on the number of modules connected to the device, it is necessary to select

the control current by choosing a resistor with the appropriate resistance. The table below shows

the correct selection of resistors:

6. DRIVER OUTPUT CURRENT SETTING

1 digit

2 digit

Tolerance

Multiplier

Tolerance

Multiplier

Resistor 4,7k - 10% - E12

Resistor 68,1k - 1% - E96

1 digit

2 digit

3 digit

Tolerance

Multiplier

Tolerance

Multiplier

In the absence of any connection between resistor and PX319 driver, it will operate with adjusted

250 mA output current (as for 100 Ohm resistor connection).

Below is the table allowing for the selection of resistor barcodes:

Color

Significant

figures

Multiplier

Tolerance

Temperature

coefficient

None

20%

Silver

x0,01

10%

Gold

x0,1

Black

Brown

x10

Red

x100

Orange

x1000

Yellow

x10.000

Green

x100.000

0.50%

Blue

x1000.000

0.25%

Purple

x10.000.000

0.10%

Grey

x100.000.000

White

x1000.000.000

Example of the resistor identification:

Irrelevant

You can connect an external 4K7 thermistor to the driver. As the temperature exceeds 70ºC, the

driver starts to limit output power. Once a 90ºC threshold is exceeded, complete shut off is carried

out.

If no NTC thermistor has been connected: 100% of power available at the output

NTC thermistor short circuit: 0% of power available at the output

6.1. TEMPERATURE CONTROL

PX319 must be connected to DMX line in series. This means that DMX IN terminals in the device

must be provided with the driving cable, and then from DMX OUT connector the driving cable

must be provided to other DMX receivers.

If PX319 is the last device in DMX line, DMX Out terminals must be provided with the terminator –

resistor of 120 Ohm between pins “+” and “-”.

120 Ohm

CORRECT INCORRECT

DMX-512 input DMX-512 output DMX cable

7. CONNECTION DIAGRAM

linear LED module

to successive modules

DMX controller

1 2 3 4 5 6

PX015

1 2 3 4 5 6 Chaser Scene

Club 6p

% 100

100 %

Master

Music Speed

GND

DMX-

DMX+

12 - 48 V DC

power supply unit

V- V+

L N

linear LED module

DC IN

42VDC

temperature sensor

NTC 4K7 thermistor

resistor setting the output

current for PX319

lamp housing

511

12 - 48 V DC

2 A

0,5 W

250 - 2000 mA

screw terminals

0,14 kg

132 mm

47 mm

21 mm

- DMX channels:

- Output channels number:

- Power supply:

- Maximum current consumption:

- Power consumption without load:

- Scene brightness:

- Output load:

- Output sockets:

- Weight:

- Dimensions:

Width

Height

Length

9. TECHNICAL SPECIFICATION

8. TECHNICAL DRAWING

132 mm

21 mm

47 mm

124 mm

FRQ

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere PXM Controller Handbücher

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung