- 5 -
10. PITCH CONTROL SLIDER
To match the choices of playback speed (8%, 16%, 32%,
100%), you can choose what range you want between
minimum (up side) and maximum (bottom side) by moving
the pitch control slider.
11. SAM. BUTTON
Sampler is a kind of sound effect that you record the music
from the track. While playing the music, you can use the
sampler to mix with music. The maximum length is 8 seconds.
1. Set start point: Press the MEMO key, and then press
SAM button, after memorizing the SAM button flashes quickly
(2 times in 1 sec)
2. Set End point: Press the SAM button again, when the
end point is memorized, the SAM button lights up (not flash).
3. Play Sampler: During PLAY mode, press the SAM
button, then the button will flash slowly. (1 time in 1 sec)
12. TRACK BUTTON
These buttons select the track to be played.
13. +10 BUTTON
Press the button to forward 10 tracks. If you forward 10 tracks,
and the tracks over total tracks, the unit will jump to track 1...
between PLAY and PAUSE modes.
14. HOT-CUE
This unit will allow you to play from 3 cue points instantly.
a. Set CUE memory: Press the MEMO button first, and
then press the CUE button to complete the CUE setting,
then this CUE button will light up.
b. Play” CUE” memory: Upon pressing specific CUE button,
it will flash about 5 seconds.
Note: This function is not available during perform
REVERSE sound effect.
15. BPM BUTTON
You can get the BPM number automatically or manually.
Pressing the BPM BUTTON for 3 seconds to switch
between auto and manual control. The BEAT will be shown
on the display! Under the manual mode, tapping this button
to get the beat value.
16. PLAY/ PAUSE BUTTON
Each press of this button causes the operation to change
between PLAY and PAUSE modes.
17. CUE BUTTON
The cue function allows the CD returning to the memorized point.
In PAUSE mode, pressing the CUE button to set the cue point,
and the CUE button blinks; in PLAY mode, press this button to
pause the unit at the memorized point
18. BOP BUTTON
The playback will automatically play from the CUE point upon
the button is pressed.
19. Seamless Loop (2 sets)
There is A, B/LOOP/ EXIT, RELOOP buttons.
i.. A BUTTON---“start point” (A point. Also, Cue 1 could be A
point) After setting up the A point, the red Led light up
ii.. B/LOOP/ EXIT BUTTON: ---“ End point”(B point). Press the B
/LOOP button to set up the B point and start the loop playback
automatically. Loop lights on the display and the 3 LEDs flash.
Press this button again to exit the LOOP playback.
iii.. Return to the loop playback by pressing the RELOOP while in
performance. However, if your want to return to loop playback,
you can press RELOOP BUTTON
iv.. Change “ START POINT” and” END POINT” by pressing the
A& B/ LOOP/ EXIT button again
v.. The interval between A and B point must be more than 20
frames; otherwise, the B point will be canceled, then LOOP
function disappear and LOOP fades on the display
20. JOG WHEEL
*Speed Control (SEARCH indicator off)
Rotating the wheel, in play mode, will change the playback
speed accordingly. While rotating clockwise, the player
speed increase; rotating counterclockwise, the speed
decrease.
*Search (SEARCH indicator lights)
Rotating the wheel, the player will forward or backward
quickly. The searching speed changed according to the
dialing speed. It can be carried out by one frame increment.
The searching speed changed according to the dialing
speed. It can be carried out by one frame increment.
21. SEARCH BUTTON
Pressed the button to switch the function of Jog Dial
between SEARCH and PITCH BEND.
zWhen the indicator LED is light, dial the jog for quick
search forward and backward.
zWhen the indicator LED is off, dial the jog for pitch bend
function.
zIf the jog is unmoved for 8 seconds, the indicator is off,
and the jog is for pitch bend function.
22. SOUND EFFECT
REVERSE: The music is playing backward. This sound effect
can be performed independently, or in parallel with other effect.
SCRATCH: Move the JOG Wheel backward or forward like
scratching a turntable record. This sound effect can be
performed independently, or in parallel with other effect.
23. CONNECTOR PORT
The 8-pin(6-pin) termination permits the connection of the
control unit to the main unit.
24. SLEEP:
Leave the unit unused for 30 minutes; the machine will shut off
automatically.
