Pyle PLCD41MP Bedienungsanleitung
Car Audio Hifi System
WNER'S MANUAL
CD/MP3
AM/FM RECEIVER
PLAYER......
R
PLCD41MP
1
Power
Volume
Eject
Mode
Loud
Dsp
Clock
Release
Play/pause
Scan
Repeat
Shf
Volume setting
Bass setting
Treble settting
Balance setting
Fader setting
Band
Band tuner
Direct access tuning
Radio wiring
Speaker wiring
Install the unit
Removing the unit
Loading and Replacing the battery
Basic operation
2
To prevent injury or fire,take the
following precautions:
To prevent damage to the machine,
take the following precautions:
Insert the unit unt l it is firmly locked to the
main unit, otherwise it may
fall out of place when jolted
When extending the ignition, memory
back up or ground cable, use diameter of
0.75mm(AWG18) or
more automotive grade cable to avoid wire
deterioration or damage
to the wire coating.
To prevent short circuit, never put or leave
any metallic object into the unit.
If you smell or see smoke, turn off the
power immediately and consult your dealer.
Be careful not to drop or shock the unit
strongly, it may break or crack because it
contain glass parts.
i
Be sure the unit is connected to a 12V
DC power with a Negative Ground
The unit is only designed for use with 4
speakers. Do not combine output for use
with 2 speakers. Do not ground negative
speaker leads to the chassis ground
Do not open the top cover and do not install
theunitin
place where it is exposed to direct sunlight
(including the faceplate),in order to avoid high
heat or humidity, water splash over it or dust.
Do not touch the terminals of the units.
Attaching panel
Attaching panel
Attach the front panel by fixing
the left side of it into this unit as1
showing.Then push the right side
of panel towards into connecting
plug as 2 showing.
If you have difficulty in installing this unit
in your vehicle. Please contact your dealer.
If the unit seems not work in properly press
the reset buttonto reset the memory of the
unit.
Follow this easy wiring diagram in order to enable you to install
the new or existing RADIO and SPEAKER wring system.
Be sure the unit is connected to a 12 volts battery with negative ground.
Good ground connections eliminate most electrical noise problem and
require tight with the metal vehicle chassis. remove plastic, paint or dust
for good electrical contact.
SPEAKER WIRING
Theunitisonlydesignedfortheusewith4speakerssystem,itcan
only be connected with speakers rated in the load impedance range
from 4 to 8 ohms. Load impedance less than 4 ohms could damage
the unit.
Never combine (BRIDGE) the outputs for use with 2 speakers, and
Never ground any Negative speaker to the chassis ground.
CAR ANTENNA
RED RCH
WHITE LCH
RCA line outRCA line out
Green Grey
Green
/white
Grey
/white
Left Front Right Front
Brown Blue
Brown
/white
Blue
/white
Left Rear Right Rear
3
RED RCH
WHITE LCH RCA line outRCA line out
Connect to control for antenna
or remote control for amplifier. Orange
Connect to battery or +12 volts of
power source that is always live.
Black
Ground-
Red
12V+
Connect to lgnition key switch.
CAR ANTENNA
Memory+ YELLOW
Subwoof
RED RCH
WHITE LCH
Auxin
Before installing the receiver permanently, fit it in the approximate place in your car Connect the
equipment according to the speakers and electrical connections. When
your system is operated properly,(preferably with the
car engine running), follow the instructions
for permanent installation
of your system.
1) Adapter
(not supplied)
2)Bend over tabs
of half sleeve
(supplied)
3)Support strap
(supplied)
Half sleeve
(supplied)
4) Two wrenches for release
the unit (supplied)
INSTALL THE UNIT
1)Install half sleeve, can be with or
without adapter. It will fit better
with adapter.
2)Bend over some tabs where possible
tosecure the half sleeve inside of dash.
3) Support strap to bestrutted under
dash, secure this strip to avoid skipp
ing of disc.
Insert removal wrench into the small
gap on the right side of the unit and pull
the unit slightly out on the same side,
then release the wrench. Repeat the
same action for the left side. By now,
you can remove the unit and unplug
the wires connector.
REMOVING THE UNIT
4
SCN RPT SHF BAND CLOCK MODE
VOL
1234 56
DSP
PWR
SEL
SEEK
Power
Turning ON the power
Press the [PWR]button.
Volume
Press to turn on the unit power,Press the button to turn off
the unit.
5
POWER ON
/OFF
DSP CLOCK
EJECT
SELECT
VOL+
VOL-
RELEASE
LCD display
Increasing volume
Decreasing
Rotate the [VOL+]button
Rotate the [VOL-]button
ST
LOC
LOUD
CH
MODE
Eject
Out
In
Press the [ ]button to eject the disc out of the unit .
Press the [ ]button again,
to load the disc in.
EJECT
VOLUME
VOL
SEL
6
Short press this button to DSP
Press LOUD button once, ROCK will bicker on display.
Press LOUD button twice, POP will bicker on display.
Press LOUD button third, CLASS will bicker on display.
Release
press the " " button to release faceplate.
Clock
Short press CLK can display time even power off .
Long Press CLK for 3 seconds will enter set mode.
MODE
Selecting radio and play
Press the [MODE]key.
Each time you press the key, it`ll switch between radio
and CD position.
(If mode with AUX IN,the function is below:
press MD(MODE)to select:
1 If with DISC,press MD that is:
2 If without DISC,press MD that is:
Press [ ] button to set the hour.
Hour
It will quit clock set mode If there is no operation
in 5 seconds.
Minute
Quit clock set mode
Press [ ] button to set the minute.
DSP
Band(Loud)
Long press the [BD/LD]button to emphasize the bass output,
Long press it again to resume the normal listening.
LOUD
AUX IN RADIO DISC AUX IN
AUX IN RADIO AUX IN
Dsp
VOL
SEL
SCN RPT SHF BAND CLOCK MODE
VOL
1234 56
DSP
PWR
SEL
SEEK
VOL+
VOL-
PRESS
Speaker mode
7
SELECT
PLAY/PAUSE
SCAN
REPEAT
SHF
DSP
VOLUME
BAS -6BAS -6
VOL 10VOL 10
TRE 5TRE 5
BAL 4BAL 4
FAD -3FAD -3
Press SEL button once,display shows VOL ,
then rotate the volume + button
to adjust volume level up.rotate
the volume - button to
adjust volume
level down.
Volume set mode
Bass set mode
Press SEL button twice,display shows BAS ,
then rotate the volume + button to adjust bass
level up. rotate the volume - button to adjust
bass level down.
Treble set mode
Press SEL button third,
display shows TRE ,then
rotate the volume + button to adjust treble
level up. Rotate the volume - button to adjust
treble level down.
Press SEL button fourth
display shows BAL ,then
rotate the volume + button
to adjust right speaks level .
Rotate the volume - button
to adjust left speaks level .
Balance set mode
Fader set mode
Press SEL button fifth,display shows FAD ,then
rotate the volume + button to adjust rear speaks
level. Rotate the volume - buttonto adjust front
speaks level.
VOLUME BASS
BALANCE
TREBLE
FADER
In press mode, VOL is sel function
8
Scan
Press this button once for TRACK INTRODUCTION.
The first 10 seconds of each track on the disc will play. And the
track number shows on LCD.
To select a desired song, press [SCN]button while it is playing.
Press [SCN]button
Play/pause
Play
If with DISC in unit,Press the [ ]to pause music.
Pause
Press the [ ]button again ,then come back to
DISC playing.
Shf
Press[SHUF]buttontoplayallthe trackinrandomorder.
SHF and playing song number will appear on the LCD.
Press [SHUF]again will stop random playing.
Press [SHF]button
Repeat
Press [RPT]button
REPEAT
Press [REPEAT] button to repeat the track continuously.
RPT and the playing song number will appear on the LCD.
Press [REPEAT] again will be back to normal playing.
SCN RPT SHF BAND CLOCK MODE
VOL
1234 56
DSP
PWR
SEL
SEEK
Band
9
SEEK+
SEEK-
BAND
PRESET MEMORY 1-6
Tuner
the long press button it can automatically select higher
frequency station. And the long press it can automatically
select lower frequency station.
In radio mode:
manual tuning:
short press button it can select higher frequency station.
Short press can select lower frequency station.
Auto loading tuning:
FM1 FM2
FM3AM
Press BAND button to select among three FM or two AM bands.
(FM1-FM2-FM3-AM)
Selecting band
Preset memory
In any band play, keep pressing AS/PS on the remote control into
automatic storage. And 6 powerful stations in this band will be stored
into NO.1-6 respectively.
There are 6 bands for selection:FM1,FM2,FM3,AM.Make selection
by pressing BAND Button.
Manual Preset Station
Please keep pressing any of the No.1-6 button to store when you
hear the favorite broadcasting station.
Automatic Preset Station
Selecting and pressing the buttons stored,you can play the station
you want then.
Selecting and pressing the buttons stored,you can play the station
you want then.
If with DISC in unit, press [MODE] switch to radio MODE first.
Inhaltsverzeichnis
Andere Pyle Autoempfänger Handbücher
Pyle
Pyle PLTV165 Bedienungsanleitung
Pyle
Pyle PLDNV111 Bedienungsanleitung
Pyle
Pyle PLCD55 Bedienungsanleitung
Pyle
Pyle PLCD11MRKT Bedienungsanleitung
Pyle
Pyle PLTVD122 Bedienungsanleitung
Pyle
Pyle PLCD26 Bedienungsanleitung
Pyle
Pyle View PLTDF25 Bedienungsanleitung
Pyle
Pyle PLCD85XMP Bedienungsanleitung
Pyle
Pyle PYLE Hydra Series PLMR19W Bedienungsanleitung
Pyle
Pyle PLDN72BT Bedienungsanleitung
Pyle
Pyle PLTS78DUB Bedienungsanleitung
Pyle
Pyle PICL82 Bedienungsanleitung
Pyle
Pyle PLD35MU Bedienungsanleitung
Pyle
Pyle PLCD46 Bedienungsanleitung
Pyle
Pyle PLCD43MRB Bedienungsanleitung
Pyle
Pyle PLMR89WW Bedienungsanleitung
Pyle
Pyle PLDD75BG Bedienungsanleitung
Pyle
Pyle PLDVD140 Bedienungsanleitung
Pyle
Pyle PLMRDK18B Bedienungsanleitung
Pyle
Pyle PLCD51BT Bedienungsanleitung
