Pyle PLCMDVR5 Bedienungsanleitung
Mirror Mount Video Monitor/Recorder with
Front and Rear View Night Cameras
PLCMDVR5
www.pyleaudio.com
Instruction Manual
Installation and Connection:
1. Please disconnect your car battery.
2. In the contents of your box there should be a wire harness that plugs into the male
receiving connection cable of your mirror mounted monitor/camera. We are not
going to plug it into to your monitor yet. There should be yellow, red, black & green
wires coming from the small plastic square at the end of the wiring harness cable.
3. Attach the black wire to your vehicles metal body or any available ground wire.
4. Attach the red wire to any available ignition controlled positive 12V power source,
mostly likely located at the fuse box.
5. Attach the yellow wire to any available positive 12V power source that is always live
and is not
6. Connect the green wire to the positive wire going to your reverse tail lights so that
the monitor will receive a 12V signal from this wire when the car is put in reverse.
controlled by your ignition, mostly likely located at the fuse box.
7. Attach the monitor/front view camera to your rear view mirror using the slide
clamps in the rear of the monitor.
8. Then plug the cameras male plastic cable into the female receiving connection at the
other end of the monitor wiring harness cable with the small black plastic square
that you just wired to your automobile.
9. Now we will decide how to mount your rear view camera. You have two options.
You can use the mounting bracket (included) with two screw holes as pictured.
Or you can use the hole saw (included) and mount as pictured.
However you decide to mount your camera please be sure that it has a clear field of
vision to the rear of your car.
10. Now we will wire your rear view camera. Take the electric DC plug black wire with
one red wire and one black wire sticking out of the end. (pictured below)
11. Attach the black wire to the vehicles metal body or any available ground wire.
12. Attach the red wire on the small power plug to your vehicles rear reverse light’s
positive wire so that it receives a 12V electrical flow when the car is in reverse.
13. Now take the long cable with the two yellow RCA plugs at each end, attach one end
to the yellow RCA plug on your camera and the other end to the yellow RCA plug on
the monitor’s wiring harness.
14. You are finished! Please re-connect your cars battery.
1. The mirror monitor buttons:
Operating Instructions for your mirror mount monitor:
Please be sure to insert SD card in the side of monitor before using.
Press ON/Off to power the unit on and off.
You can press V1/V2 to select between front and back cameras or view both at
the same time.
Press MODE to choose between MOVING VIDEO, STILL CAMERA or PLAYBACK
Mode.
When in MOVING VIDEO mode press OK to begin recording (The Video icon will
flash red while recording) and press OK again to stop recording.
When in STILL CAMERA mode press OK to take a photograph.
When in PLAYBACK mode press <&>view and scroll between pictures and videos,
press OK to play moving video.
While viewing pictures or videos press MENU to view DELETE option, Press OK
twice to delete the photo or video file.
Press MENU for two seconds when the camera is not recording and you will enter
the options and settings menu. There will be four symbols &
to choose from.
Allows you to choose between VGA and 720 MegaPixels. Push the
<&>buttons to scroll between options. Press OK to select option.
Press MODE to switch to Recording time. This allows you to choose recording
time. Push the <&>buttons to scroll between options. Press OK to select option.
Press MODE to switch to Front and Rear Record Mode. This allows you to
choose front or rear camera recording or both. Push the <&>buttons to scroll
between options. Press OK to select option.
Press MODE to switch to Settings Mode. This allows you to change all the
settings that comes with this unit, including brightness, exposure, color, screen
protector timing, IR LED illumination, G_sensor, auto detect motion sensor, water
mark, record audio, auto record, language, frequency, Back-In recording format,
date set, format memory and to reset to default settings. Push the <&>buttons
to scroll between options. Press OK to select option.
If unit freezes or ever fails for any reason please push the reset button on side of
monitor.
To download videos and pictures to your computer please connect from the mini
USB port on the side of monitor to the USB port of your computer.
Setting
function
bright
Changes your cameras ability to handle different lighting
conditions, it is best set to automatic.
exposal (exposure) Changes lenses exposure level
color Changes your cameras color selection
Screen Protector Shuts the viewing screen off after a set time
IR_LED Turns LED night vision assistance off and on
G_sensor Starts recording when the camera senses a strong impact to
the automobile in case of an accident (Camera will record
10+ seconds after power of battery stops)
auto detect Automatically records when motion is detected by camera
Water mark Adds date and time stamp information to photograph or
video being recorded
record audio Turns the ability to record sound (audio) on or off
auto record Automatically turns recording on when monitor is powered
on.
language Choose between selection of languages
frequency
Choose between 50 Hz and 60 Hz
Back_IN (Recording
format)
Choose between recording in PAL or NYSC
Monitor:
Built-in hidden screen : 4.3"TFT LCD monitor on or off
High resolution : Resolution up to 1280*960
File format: H.264 MOV Still Image JPEG
Video resolution: Dual 720p HD: 1280x1440 30fbs 8Mbps/ SD: 1280 x 480 30fbs 6Mbps
Built-in wide angle lens: Diagonal view angle is 120 degrees.
Automatic loop recording: after car power starts
Storage: Support SD/SDHC up to 32GB.
Audio: Synchronized video/audio recording
Low illumination image sensor
Lens adjustable 360 degree.
Back up Camera function
No recording gap between file clips.
Keeps recording for 10+ seconds after power stops when there is an impact (G-SENSOR function).
Wide angle rearview mirror
Visible area: 10"
Image sensor: Mega pixels 1/4 CMOS Sensor )
View angle: 120 degrees
Pixels: 1.3 Mega pixels
Video Output: NTSC/PAL
date set Set the date and time recorded
format Formats SD flash card memory (Erases)
default set Resets all setting to the factory default
Operating voltage: 12V
Power consumption : 0.5A
Supports: Windows 2000/XP/Vista/7/8
Mirror Mounted Monitor
Dimension: 10.6" x 3.1" x 1.2"
Camera:
Rear View Camera with Optional Dual Flush/Universal Mount Brackets
420 Line Horizontal Resolution
Built-in Distance Scale Line
Low Lux
Resolution: 420 TV Lines
Viewing Angle: 170 Degree
Auto White Balance
Waterproof (Ip68), Fog Resistant
Video Output: 1.0V PP-75 Ohm
Power Supply: DC 12V
Inhaltsverzeichnis
Andere Pyle Dashcam Handbücher
Pyle
Pyle PLDVRCAM25 Bedienungsanleitung
Pyle
Pyle View PLCM37FRV Bedienungsanleitung
Pyle
Pyle PLCMDVR77 Bedienungsanleitung
Pyle
Pyle pdvrcam11 Bedienungsanleitung
Pyle
Pyle PLCM18BC Bedienungsanleitung
Pyle
Pyle PLDVRCAM44 Bedienungsanleitung
Pyle
Pyle PLDVRCAM71 Bedienungsanleitung
Pyle
Pyle PLDVRWFI65 Bedienungsanleitung
Pyle
Pyle PLCM32 Bedienungsanleitung
Pyle
Pyle PLDVRCAMG37 Bedienungsanleitung
Pyle
Pyle PLCMTR5 Bedienungsanleitung
Pyle
Pyle PLCM4567 Bedienungsanleitung
Pyle
Pyle PLCMDVR54 Bedienungsanleitung
Pyle
Pyle PLCM7400BT Bedienungsanleitung
Pyle
Pyle PLDVRCAM74 Bedienungsanleitung
Pyle
Pyle PLCM4300WIR Bedienungsanleitung
Pyle
Pyle Surveil PLDVRCAMAND75 Bedienungsanleitung
Pyle
Pyle PLCMDVR46 Bedienungsanleitung
