Pyle Secure Scan PMD38 Bedienungsanleitung

Handheld Metal Detector

Wand Security Scanner

PMD38

Instruction Manual

1、Detection

2、LED(Green/Red Color)

3、Audio Alert

4、Handle

5、Battery Door)

6、Low Sensitivity Switch

7、Power On/Off switch

8、Rechargeable Battery Socket

9、Sound or Vibration switch

10. Deep inset sensitivity control

2. Function

1) As electronic security device utilized in airports, security stations and ports.

2) The security check of customs, police, immigration and corrections.

3) As a quality check device used in food and medication manufacture.

4) The security check at sport events, concerts and public gatherings.

5) Precious metals check, such as at a gold and silver factory

3. Distance of detection Detection Distances Can Be Adjusted

1)pin

.4 inch

2) 6 inch metal

wall stud

4.7 inch

3) φ20mm steel

ball

2.7 inch

4. Feature

1) High sensitivity

2) It is easy and convenient to use, no adjustment necessary

3) The two selectable warning options are sound and vibration.

4) Battery depletion warning : automatic continuous sound or vibration alert

5) The two choices of high or low sensitivity

6) External charging jack.

5. How to Replace Battery

1) Use thumb to push battery cover open (push in direction of arrows)

2) Plug 9V battery into wired receptacle paying attention to polarity (Do not plug device into

electric wall adapter if using non-rechargeable alkaline battery. May damage battery and cause

injury )

3) Replace battery lid and push tight with thumb

6. Application Method

1) Turn on the switch (7), hear the "tone" sound, 3-5 seconds, power has been turned on, self-

test time is completed, you can use unit while green light is lit. If green light is not lit than

battery is not installed properly. The battery connection may be bad if continuous sound or

vibration occurs. Alkaline batteries cannot be reused they must be disposed of and replaced.

2) Sound, vibration switch options: press the red button switch (9), alarm is in vibration mode.

Release the red button switch (9), alarm in sound mode.

3) After power is turned on, you can perform high-sensitivity testing, grip the handle and

sweep wand near metal object. The metal should be detected as wand sweeps by the object,

the alarm will sound or vibrate when near metal, green light will illuminate red when metal is

detected. It will return to green and sound or vibration will stop when no metal is near sensor field.

4) Low sensitivity test: If you need to exclude the very small metal objects, you can hold down

the low sensitivity switch (6). Then conduct exploration sweep around the measured object,

alarm will only sound when metal is large enough to detect as the wand sweeps by the object,

the alarm will sound or vibrate when near metal. The light will illuminate red when metal is

detected. It will return to green and sound or vibration will stop when no metal is near sensor field.

Sensitivity is reduced by 5 times when sensitivity switch is activated.

7. Sensitivity Adjustment

1) If the detection range does not meet your requirements or if detection is unstable or too

sensitive you should adjust the sensitivity. If units geo-chemical detection detects body parts or

other non-metal objects than sensitivity needs to be adjusted. Adjustment can be made by

inserting a small flat head electronic screwdriver into hole and turning small reo-stat. Please

do not try to adjust sensitivity with an object other than tools specified for the job.

2) Select the sound, vibration switch (9) when released detector will sound, use a small

electronic screwdriver in the adjustment hole. When you feel that the screwdriver is seated in

adjustment slot turn counter clockwise to increase sensitivity. Turn clockwise to decrease

sensitivity. Hold unit next to metal object and listen to alarm until required range is found.

8. Attention

1) Do not forget the power off after use.

2) If not being used for a long period of time, remove battery.

3) Top of probe not intended for detection, sides of probe are the detection area during

sweeping motion.

4) When Charging, please turn off the power switch (7).

5) Charger voltage: DC 10V (with charger).

Andere Pyle Metalldetektor Handbücher

Pyle

Pyle PMD43 Bedienungsanleitung

Pyle

Pyle PMD58 Bedienungsanleitung

Pyle

Pyle PHMD55 Bedienungsanleitung

Pyle

Pyle PMD24 Bedienungsanleitung

Pyle

Pyle PHMD3 Bedienungsanleitung

Pyle

Pyle PHMD74 Bedienungsanleitung

Pyle

Pyle PHMD72 Bedienungsanleitung

Pyle

Pyle PHMD2 Bedienungsanleitung

Pyle

Pyle PHMD53 Bedienungsanleitung

Pyle

Pyle PHMD84 Bedienungsanleitung

Beliebte Metalldetektor Handbücher anderer Marken

Garrett

Garrett MAGNASCANNER CS 5000 Bedienungsanleitung

Valex

Valex 1800200 Bedienungsanleitung

Gauss

Gauss MIL MD Bedienungsanleitung

Velleman

Velleman CS130 Bedienungsanleitung

Sears

Sears 321.596370 Bedienungsanleitung

Eriez

Eriez X8 Bedienungsanleitung

Steinberg Systems

Steinberg Systems SBS-MD-22 Bedienungsanleitung

Zircon

Zircon MetalliScanner m60c Bedienungsanleitung

nalanda

nalanda MD027 Bedienungsanleitung

REV Ritter

REV Ritter CB-7005 Bedienungsanleitung

Minelab

Minelab F1A4 Bedienungsanleitung

Fisher Research Labs

Fisher Research Labs F70 Bedienungsanleitung

Steinberg Systems

Steinberg Systems SBS-MD-12 Bedienungsanleitung

GOLDEN MASK

GOLDEN MASK 5 Bedienungsanleitung

Grizzly

Grizzly YM 203 Bedienungsanleitung

Fisher Research Labs

Fisher Research Labs 1280-X Aquanaut Bedienungsanleitung

Treasure Cove

Treasure Cove Vibra-Probe 560 Bedienungsanleitung

Accurate Locators

Accurate Locators XL16 IMAGER Bedienungsanleitung