QCAMZ FULL HD Bedienungsanleitung
// English
QCAMZ FULL HD 1080p
170° Fisheye Waterproof // Action Cam
Introduction
Thank you for purchasing the QCAMZ FULL HD! Record your limits with this waterproof full HD
action cam!
It is highly recommended for you to read this user manual carefully in order to fully understand how
to operate the QCAMZ FULL HD correctly.
Table of Contents
What’s in the box?
How to use
Camcorder Overview
Initial set up
Charging the battery
Power ON/OFF
Taking a video
Taking snapshot photos
Memory capacity chart
Digital Video Motion Stabilisation Technology
Playback on your computer
On a Mac
Date & time setting
Webcam setting
Firmware Installation
LED status table
Removing/Installing battery
Repairs
Technical specications
Warranty
Warning
What’s in the box? 1. QCAMZ FULL HD with Sound Cap
2. Camcorder Mount
3. Universal Mount
4. Roll Bar Mount
5. Pad Mount
6. Rotating Kitset
7. Magic Tape 2pcs
8. Adhesive Stickers 8 pcs
9. Waterproof Cap
10. Rubber O-Rings 6 pcs
11. Silicon Grease
12. Hand Safety Strap
13. Rechargeable Lithium-Polymer Batteries 2 pcs
14. USB Cable
15. User Manual
How to use the QCAMZ FULL HD
1. Camcorder on Handlebar 2. Camcorder on Vented Helmets
Roll Bar Mount Camcorder Mount Magic Tape 2pcs Universal Mount Camcorder Mount
3. Camcorder for Non-vented Helmets 4. Camcorder on top of Helmet
Adhesive Sticker Universal Mount Camcorder Mount Adhesive Stickers Pad Mount Rotating Kitset Camcorder Mount
6. Camcorder on Surfboard or any curved surface
5. Camcorder on Front Helmet
Adhesive Stickers 4pcs Pad Mount Rotating Kitset Camcorder Mount Adhesive Stickers 4pcs Pad Mount Rotating Kitset Camcorder Mount
Using QCAMZ FULL HD for water sports
When using the waterproof cap remember to put some silicon
grease to the rubber O-ring from time to time, especially before
using the camera in water. Make sure to close the rear cap ③
tightly. Only use the camera in water with the waterproof cap!
Rubber O-Rings Silicon Grease Waterproof Cap
4. Mode switch
5. USB Port
6. Micro SD card slot
7. Battery
8. Microphone
9. 1080P / 720P mode switch
10. Stabiliser / rmware switch
CAMCORDER OVERVIEW
1. LED
2. Power / Shutter
3. Rear cap
Initial set up
1. Make sure the camera is OFF before inserting in or removing the Micro SD card!
2. Unscrew the rear cap from the back of the camera ③.
3. Put your Micro SD card (max up to 32GB) into the slot with the card label facing
down (contacts up). Use your ngernail to do this. You will hear a click sound once
the Micro SD card is in place. Then screw the rear cap back on tightly.
Only use Micro SD cards Class 6 or above.
4. If no Micro SD card is inserted into the camera, the LED light on top of the ca-
mera will start ashing red and blue for approx. 30 secs and then auto shut-off.
5. The Micro SD card must be blank; meaning without images from other sources
on it. If you are using a Micro SD card previously used with other cameras, please
make sure you format the Micro SD card in your computer before using it with
your QCAMZ FULL HD. New cards can be used straight from the packaging.
Charging the battery
Unscrew the cap located at the back of the camera ③ and connect the camera
with the USB cable to your PC ⑤ or charger (optional). The LED light will glow
green while charging and goes off once the battery is fully charged.
Before the rst use charge the battery for 10 hours! You can record
approx. up to 90 minutes with one charge.
Power on/off
Turn on the camera // Press and hold the POWER/Shutter button for approx. 3
seconds until the blue LED turns on and the red LED ashes once. The camera
will beep and vibrate once long, indicating it is now in stand-by mode.
Turn off the camera // Press the POWER/Shutter button again for approx.
3 seconds. The LED light will go off and the camera will short vibrate twice,
indicating it switches off.
Standby mode // If the camera is in standby mode without activity, it will auto
switch off after approx. 3 mins to conserve battery power.
Inhaltsverzeichnis
Andere QCAMZ Action-Kamera Handbücher
