QEP 16600 Bedienungsanleitung

TUNGSTEN CARBIDE CIRCULAR CUTTER

WARNING! READ THE OPERATING AND SAFETY

INSTRUCTIONS BEFORE USE. ALWAYS WEAR SAFETY

GLASSES, GLOVES AND OTHER APPROPRIATE SAFETY

ITEMS FOR PROTECTION. IMPROPER USE WILL VOID

THE WARRANTY.

CAPACIT Y

1. For cutting round holes in ceilings, wall and floors

2. Cuts holes with diameter:

40mm – 125mm / 40mm – 205mm / 48mm – 305mm

3. Cutting depth: 3-30mm (one-sided) / 60mm (two-sided)

4. Cuts veneer, plywood, gypsum-board, plaster,

acrylic-sheet, fibre cement board, etc.

MOUNTING THE BLADES

The tungsten carbide blades have to

be mounted as shown in Fig. A + C

The tapered steel blades are

suitable for plastics and acrylic only.

ADJUSTING THE CUTTING DIAMETER

Fig. B: The blade holders can be repositioned on the

measuring bar. Use the hexagonal wrench to loosen the

screws and push the blade holders to the required

position. Both blades must be the same distance away

from the drill position/central point. Tighten the screws

firmly before cutting.

CAUTION

Before cutting, securely clamp the material to be cut.

Start cutting after carefully setting the pilot drill at the

centre of the desired hole. The circular cutter must not

be used without its protective cover. When using a power

drill, be sure to align the hole cutter so that both blades

start cutting at the same time, gradually cutting through

the work piece. Abrupt contact of the blades with the

work piece may cause the drill to stall or kick back and

result in injury to the operator.

TUNGSTEN CARBIDE CIRCULAR CUTTER

WARNING! READ THE OPERATING AND SAFETY

INSTRUCTIONS BEFORE USE. ALWAYS WEAR SAFETY

GLASSES, GLOVES AND OTHER APPROPRIATE SAFETY

ITEMS FOR PROTECTION. IMPROPER USE WILL VOID

THE WARRANTY.

CAPACIT Y

1. For cutting round holes in ceilings, wall and floors

2. Cuts holes with diameter:

40mm – 125mm / 40mm – 205mm / 48mm – 305mm

3. Cutting depth: 3-30mm (one-sided) / 60mm (two-sided)

4. Cuts veneer, plywood, gypsum-board, plaster,

acrylic-sheet, fibre cement board, etc.

MOUNTING THE BLADES

The tungsten carbide blades have to

be mounted as shown in Fig. A + C

The tapered steel blades are

suitable for plastics and acrylic only.

ADJUSTING THE CUTTING DIAMETER

Fig. B: The blade holders can be repositioned on the

measuring bar. Use the hexagonal wrench to loosen the

screws and push the blade holders to the required

position. Both blades must be the same distance away

from the drill position/central point. Tighten the screws

firmly before cutting.

CAUTION

Before cutting, securely clamp the material to be cut.

Start cutting after carefully setting the pilot drill at the

centre of the desired hole. The circular cutter must not

be used without its protective cover. When using a power

drill, be sure to align the hole cutter so that both blades

start cutting at the same time, gradually cutting through

the work piece. Abrupt contact of the blades with the

work piece may cause the drill to stall or kick back and

result in injury to the operator.

Model No. 16600, 16601, 16602

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere QEP Cutter Handbücher

QEP

QEP 10267 Bedienungsanleitung

QEP

QEP 10214Q Bedienungsanleitung

QEP

QEP Vitrex VERSATILE Power Max 560 Wartungs- und Serviceanleitung

QEP

QEP 10-37 Bedienungsanleitung

QEP

QEP 10267 Bedienungsanleitung

QEP

QEP PRO 21 Bedienungsanleitung

QEP

QEP 10630Q Bedienungsanleitung

QEP

QEP Vitrex Versatile Power Max 560 Wartungs- und Serviceanleitung

QEP

QEP 10221Q Bedienungsanleitung

QEP

QEP 20” Bedienungsanleitung

QEP

QEP 10420Q Bedienungsanleitung

QEP

QEP Vitrex VERSATILE Power Pro 600 Wartungs- und Serviceanleitung

QEP

QEP 10500 Bedienungsanleitung

QEP

QEP Vitrex Clinker XL Bedienungsanleitung

QEP

QEP 10424Q Bedienungsanleitung

Beliebte Cutter Handbücher anderer Marken

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Bedienungsanleitung

Makita

Makita DCS552 Bedienungsanleitung

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Bedienungsanleitung

Makita

Makita 4112HS Bedienungsanleitung

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Bedienungsanleitung

Hitachi

Hitachi CM 4SB2 Fehlerbehebungshandbuch

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Bedienungsanleitung

GCC Technologies

GCC Technologies AFJ-24S Bedienungsanleitung

DeWalt

DeWalt XR LI-ION DCS350N Bedienungsanleitung

Baudat

Baudat ES1 Bedienungsanleitung

Mafell

Mafell ZAF 200 Leitfaden

Makita

Makita 4100NH Bedienungsanleitung

Formax

Formax FD 574 Bedienungsanleitung

EINHELL

EINHELL TE-MA 1500 Bedienungsanleitung

Husqvarna

Husqvarna Cut-n-Break K 760 Bedienungsanleitung

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Bedienungsanleitung

TRI tool

TRI tool 301A Bedienungsanleitung

Roller

Roller King 1 1/4 Bedienungsanleitung