Qlogic SANbox 3050 Bedienungsanleitung

Quick Start Guide

[]

FIBRE CHANNEL SWITCH INSTALLATION P

QUICK START GUIDE

SANbox®3050

for Windows®Operating Systems

Quick Start Guide

Congratulations on your purchase of the SANbox 3050™ Fibre Channel switch. This Quick Start

Guide describes how to install and activate your SANbox 3050 switch using a Windows

workstation.

Prerequisites

• Workstation

• Operating systems:

• Windows NT/2000/2003

• Linux® Red Hat® 7.2

• Solaris® 2.8/2.9 CDE

• 256 MB memory

• 156 MB disk space

• 300 MHz processor

• Video card with 256 colors

• CD ROM drive, RS 232 serial port, RJ-45 Ethernet port

• Crossover cable to connect the workstation and the switch

• IP address, subnet mask, and gateway to assign to the switch

Switch Installation Procedure

Step 1. Verify the Package Contents

Step 2. Mount the Switch

Step 3. Install SFPs

Step 4. Apply Power to the Switch

Step 5. Install the SANbox Manager Application

Step 1. Verify the Package Contents

The SANbox 3050 Fibre Channel Switch is shipped with the following items:

1 SANbox 3050 Fibre Channel Switch

1Powercord

4 Rubber feet

2 Mounting brackets

8 Mounting screws

1CD

NOTE: Small Form-factor Pluggable (SFP) transceivers, if ordered, are packaged separately.

Step 2. Mount the Switch

You can mount the SANbox 3050 switch on a flat surface or in a rack.

❑For a surface mount, attach the rubber feet to the locations on the bottom of the switch

❑For a rack mount, fasten the brackets to

the switch using 2 screws on each

bracket as shown. Choose the holes in

the bracket to produce the desired set

back from the front of the cabinet. Place

the switch in a standard 19" rack and

fasten thebracket flanges to the rack with

two screws on each side.

Step 3. Install SFPs

An optical SFP is required for each switch port that will be connected to a device, device loop, or

another switch. Recommended SFP: Picolight® PL-XPL-VC-S23-11.

❑If SFPs were included in your shipment, install them now. To install an SFP transceiver,

insert the transceiver into the switch port and gently press until it snaps in place. The SFP

will fit only one way. If the SFP does not install under gentle pressure, flip it over and try again.

Step 4. Apply Power to the Switch

❑Attach the supplied power cable to the

switch and wall outlet or power strip.

Verify that the Input Power LED is on.

❑The switch runs its self tests and begins

normal operation – this may take a few

minutes. Verify that the Heartbeat LED is

blinking (once per second) and the

System Fault LED is NOT illuminated.

NOTE: The SB3050-XXX-E switch comes

complete with pre-configured zones for the

EMC ClARiiON AX100™. Follow the diagram

below to connect to your devices. If desired,

use the SANbox Manager Application to

perform advanced switch configuration.

Zone Name Switch Ports

Zone 1 1, 0

Zone 2 1, 4

Zone 3 2, 0

Zone 4 2, 4

Zone 5 3, 0

Zone 6 3, 4

Zone 7 7, 0

Zone 8 7, 4

Zone 9 5, 0

Zone 10 5, 4

Zone 11 6, 0

Zone 12 6, 4

INPUT

POWER LED

HEARTBEAT

LED

SYSTEM

FAULT LED

The pre-configured zone names and switch

port numbers are listed in the Pre-configured

AX100 Zones table.

Pre-configured AX100 Zone Table

Step 5. Install the SANbox Manager Application

To install the SANbox Manager application on a Windows workstation/server, perform the following

steps:

❑Insert the supplied CD into the CD ROM drive of the workstation/server.

NOTE: If the Welcome screen does not appear, browse the CD and run the installer program with

the following path: [CD ROM drive]\GUI\Windows_4.00.xx.xx.

❑In the Welcome screen, click SANbox Switch Manager.

❑In the License Agreement screen, click Agree.

❑Find the Installation File for the Windows operating system in the table, and click Install.

❑Follow the on-screen instructions to complete the software installation.

If you are using a Linux or Solaris workstation/server, mount the CD and run the following installer

programs based on your platform:

• Linux installer program: [CD ROM drive]/GUI/Linux_4.00.xx.xx

• Solaris installer program: [CD ROM drive]/GUI/Solaris_4.00.xx.xx

Congratulations!

You have successfully installed your QLogic SANbox 3050

Switch!

For technical support, visit our web site at support.qlogic.com, email us at support.@qlogic.com,

or call us at 952-932-4040. For more detailed installation instructions, see the SANbox 3050 Fibre

Channel Switch Installation Guide, located on the product CD or on the QLogic web site.

©QLogic Corporation. QLogic, SANbox, and SANbox Manager are trademarks or registered trademarks of QLogic Corporation. All other

trademarks are the property of their respective companies. Information supplied by QLogic is believed to be accurate and reliable. QLogic

Corporation assumes no responsibility for any errors in this brochure. QLogic Corporation reserves the right, without notice, to make changes

in product design or specifications.

QLogic Corporation 26650 Aliso Viejo Parkway Aliso Viejo, CA 92656

949.389.6000 www.qlogic.com

50327-03 A

*50327-03A*

Inhaltsverzeichnis

Andere Qlogic Schalten Handbücher

Qlogic

Qlogic SANbox 9000 Series Bedienungsanleitung

Qlogic

Qlogic SANbox 5800V Series Bedienungsanleitung

Qlogic

Qlogic SANbox 5600 Series Bedienungsanleitung

Qlogic

Qlogic SANbox2-8c Bedienungsanleitung

Qlogic

Qlogic SANbox 5000 Series Bedienungsanleitung

Qlogic

Qlogic SANbox 5600 Series Bedienungsanleitung

Qlogic

Qlogic SANbox 5602 Handbuch

Qlogic

Qlogic SANbox 5200 Series Handbuch

Qlogic

Qlogic SANbox 5600 Series Bedienungsanleitung

Qlogic

Qlogic SANbox 5600 Series Bedienungsanleitung

Qlogic

Qlogic SANbox-16HA Installer's/ Bedienungsanleitung

Qlogic

Qlogic SilverStorm 9000 Bedienungsanleitung

Qlogic

Qlogic SANbox 5200 Series Bedienungsanleitung

Qlogic

Qlogic SANbox 5800V Series Bedienungsanleitung

Qlogic

Qlogic SilverStorm 9120 Bedienungsanleitung

Qlogic

Qlogic SilverStorm 9024 Handbuch

Qlogic

Qlogic InfiniBand 12200-BS01 Bedienungsanleitung

Qlogic

Qlogic SANbox 5802V Bedienungsanleitung

Qlogic

Qlogic SilverStorm 9020 Handbuch

Qlogic

Qlogic SANbox 5600 Series Bedienungsanleitung

Qlogic

Qlogic SANbox2 SANbox2-64 Bedienungsanleitung

Qlogic

Qlogic SilverStorm 9040 Bedienungsanleitung

Qlogic

Qlogic SANbox 5800V Series Bedienungsanleitung

Qlogic

Qlogic SANbox 3810 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung