QMS Magicolor LX Allgemeine Anweisungen
Update to the
QMS
®
magicolor
®
LX
Printer User’s Guide
To update your QMS magicolor LX Printer User’s Guide, please
replace pages 2-25 through 2-26 and pages 6-13 through 6-16 with
the pages in this package.
1800414-001A
2. Hold the cleaning pad by its tab and place the white side
against the orange roller closest to the green felt strip. Align
thecenter rib ofthe cleaning padwiththe triangle onthegreen
felt strip.
3. Keep the white side of the pad touching the orange roller
closest to the green felt strip as you press the pad forward and
down into the slot under the green felt strip (fig. 2.17). It’s in
place when it clips securely into the slot with the white pad
touching the orange roller.
CAUTION: The $1000 fuser unit will be damaged if the cleaning
pad is not replaced each time the oil bottle is replaced. This type of
damage is not covered under warranty or service contract. Both
parts are included in the same kit.
Fig. 2.17 Install the Cleaning Pad (front view)
Chapter 2
Initial Printer Setup 2-25
4. Snap the separator pawl unit closed (fig. 2.18).
Fig. 2.18 Close Separator Pawl Unit (front view)
Chapter 2
2-26 Initial Printer Setup
5. Locate the cleaning pad in the slot above the heatroller. Then,
while carefully avoiding the surface of the fuser unit, which
may be hot, grasp the pad by its center tab (towards the rear
of the unit), pull it out of the printer, and discard it (fig. 6.3).
6. Removethenewcleaningpadandthenewoilbottlefromtheir
protective bags.
CAUTION: The $1000 fuser unit will be damaged if the cleaning
pad is not replaced each time the oil bottle is replaced. This type of
damage is not covered under warranty or service contract. Both
parts are included in the same kit.
Fig. 6.3 Remove the Cleaning Pad
Chapter 6
Consumables and Preventative Maintenance 6-13
7. Hold the new cleaning pad by its tab and place the white side
against the orange roller closest to the green felt strip. Align
thecenter rib ofthe cleaning padwiththe triangle onthegreen
felt strip.
8. Keep the white side of the pad touching the orange roller
closest to the green felt strip as you press the pad forward and
down into the slot under the green felt strip. It’s in place when
it clips securely into the slot with the white pad touching the
orange roller.
9. Snap the separator pawl unit closed.
10. Pull open the spring latch on the outer edge of the oil bottle
retainer, and lift the retainer up and toward the center of the
printer (fig. 2.19).
NOTE: Normally, alittle oilremainsinthefuser slotin which
the oil bottle rests, and the spout of the oil bottle has a seal to
prevent oil from spilling while you remove or install a bottle
Chapter 6
6-14 Consumables and Preventative Maintenance
on the pin in the fuser slot. However, if oil accidentally spills
beyondthatslot,usea clean,dry,lint-freeclothorsomecotton
swabs to wipe up the excess.
11. Grasp the top tab on the oil bottle, then lift the bottle out of
the printer, and discard it.
NOTE: If you are replacingan oil bottle aftera move,remove
and discard the wadded paper towel from the place normally
occupied by the oil bottle.
12. Hold the new oil bottle, spout end down, bottle label toward
the frontof theprinter, over its slotinthe fuser unit (fig.2.19).
13. Lower the bottle into place, making sure the spout on the
bottom aligns with the pin in the fuser slot. The bottle is
positioned correctly when it fits snugly into the slot and is
flush with the fuser unit.
14. Close and latch the oil bottle retainer.
15. Close the paper exit unit.
16. Replace the printer’s top cover and turn on the main power
switch.
Replacing the Waste Toner Pack
This section covers replacing the waste toner pack in your printer.
Thepackcollectsexcesstonerfromtheprintingprocessandshould
be replaced when the window on the control panel displays the
message CHECK WASTE TONER. Illustrations for many of the
steps described in this section are in chapter 2, “Initial Printer
Setup.”
1. Open the waste toner cover by pushing the cover on the
top-right corner (fig. 2.22).
2. Remove the new waste toner pack from its protective bag and
assemble it according to the instructions accompanying it.
Chapter 6
Consumables and Preventative Maintenance 6-15
3. Gently tap the old waste toner pack on its side to settle the
toner down into the pack (fig. 6.4).
WARNING! The toner is a highly combustible powder; never
burn it. Also, avoid inhaling loose toner or getting it around
youreyes;itcancauserespiratoryproblemsandeyeirritation.
ACHTUNG! Bei dem Toner handelt es sich um ein gefähr-
lichesundleicht entzündlichesPulver; esdarf deshalb niemals
mit offenem Feuer in Berührung kommen. Einatmen oder
Berührung mitHaut und Augen ist ebenfalls zu vermeiden, da
dies zuBeeinträchtigungender Atemwege, Haut- oder Augen-
reizungen führen könnte.
4. Grasp the tab onthe topedge of the old waste toner pack,and
pull it out of the printer.
Fig. 6.4 Tap the Waste Toner Pack
Chapter 6
6-16 Consumables and Preventative Maintenance
Inhaltsverzeichnis
Andere QMS Drucker Handbücher
QMS
QMS Magicolor 2 Desklaser Bedienungsanleitung
QMS
QMS DeskLaser 1600 Bedienungsanleitung
QMS
QMS 2001 Bedienungsanleitung
QMS
QMS 2560 Bedienungsanleitung
QMS
QMS ColorScript 310 Bedienungsanleitung
QMS
QMS Magicolor 2 Desklaser Handbuch
QMS
QMS 4060 Bedienungsanleitung
QMS
QMS 2025 Service-Handbuch
QMS
QMS 1660E Handbuch
QMS
QMS Magicolor 6100 Handbuch
QMS
QMS Magicolor 2 plus Bedienungsanleitung
QMS
QMS 1060 Bedienungsanleitung
QMS
QMS 1800428-001B Bedienungsanleitung
QMS
QMS 2060 WX Bedienungsanleitung
QMS
QMS 2425 Abmessungen
QMS
QMS 4060 Handbuch
QMS
QMS 19 Bedienungsanleitung
QMS
QMS Magicolor 330 Bedienungsanleitung
QMS
QMS Magicolor 2 Desklaser Bedienungsanleitung
QMS
QMS 2425 Bedienungsanleitung
