QRP Labs Ultimate3S Bedienungsanleitung

Rev 1.01 1

AN004

HF PA kit with Ultimate3S transmitter kit

1. Introduction

The QRP Labs HF PA kit has an 8-bit shift register (74HC595) whose outputs control an 8-bit Digital-

to-Analogue converter (DAC). This DAC controls a discrete-component power modulator with

foldback current limiting. A microcontroller can load a sequence of values into the shift register in

such a way that a raised cosine shape is applied to the RF envelope.

This application note explains how to interface the PA kit to the QRP Labs Ultimate3S transmitter kit.

The assembly document for the PA kit is ESSENTIAL reading, prior to this application note!

2. Block Diagram

The basic Ultimate3S transmitter is shown in the top half of this diagram. The Low Pass Filter (the

LPF) is drawn as a separate block to the Ultimate3S transmitter. In reality the LPF is a plug-in module

on the Ultimate3S PCB. If you are running a multi-band Ultimate3S then there is a LPF plugged into

your Ultimate3S PCB, and a 5-band Relay-switched extension PCB bolted behind that. As far as the

5W HF PA kit is concerned, the principles are the same in the single-band and multi-band cases.

Rev 1.01 2

The lower half of the diagram shows the modified block diagram once the 5W HF PA kit is installed.

The RF path from the output of the Ultimate3S BS170 PA originally routed directly to the Low Pass

filtering. Now we must intercept this RF and insert the 5W HF PA kit in the signal path as shown.

Additionally, control signals are required if the Ultimate3S raised-cosine envelope shaping feature is

to be used.

The interception of the RF output signal to insert the 5W HF PA kit in the path, and the connection of

the control signals, require additional wiring between the PCBs. Unfortunately It is not a matter of

plugging header connectors!

3. Physical Assembly

Physically, if you are going to bolt the 5W HF PA kit into the Ultimate3S “stack”, then you will need to

put the 5W HF PA kit at the BACK of the stack, due to the 65mm tall heatsink. You will also need to

purchase a set of four 25mm nylon spacers from the QRP Labs shop, spare parts section. The

physical module assembly is shown in the diagrams below, for the single band system (below left)

and multi-band (below right).

Please refer to section 5.4 of the PA kit assembly manual “Heatsink temperature rise; PA kit

installation in enclosure” to decide how to enclose the system – it may require additional heatsinking

or fan-assisted cooling.

4. Connections

When using the Ultimate3S transmitter to drive the 5W HF PA kit, use a single BS170 transistor in the

U3S PA, and run it at 5V. Use a 25-turn inductor in the drain circuit of the BS170 PA in the U3S, do

not use a bifilar transformer. Over-driving the 5W HF PA does not result in higher power output, but it

can result in lower efficiency (more heat dissipation).

Rev 1.01 3

The easiest place to take RF from the Ultimate3S is at the Q2 or Q3 transistors. The best way to cut

the RF circuit between the original Ultimate3S PA and the Low Pass Filter on the U3S PCB, is to

remove capacitor C5. If you don’t mind a little aggression you can even just cut it out with wire

cutters. For routing the RF output of the 5W HF PA kit back to the U3S, it is easiest to connect a wire

to the “RFI” (RF in) pad.

Single-band Ultimate3S with 5W HF PA kit

Rev 1.01 4

Multi-band Ultimate3S with 5W HF PA kit and relay-switched LPF kit

Rev 1.01 5

This diagram section (right) shows detail

of how to connect the 200mW RF from

the Ultimate3S PCB “Q3” pad, to the 5W

HF PA PCB. Remember that you will be

using only a single BS170 in the U3S, so

there will be no transistor installed at Q3.

When connecting the RF output of the 5W

HF PA back to the filter input on the

Ultimate3S, it is convenient to use the

pins of the 2 x 5 header as shown. The

RF output on the HF PA PCB is

connected to the “RFI” pin of that 2 x 5 header such that everything lines up when the boards are

stacked together. This applies whether you are using the single-band or multi-band system.

If you are brave, you could try to solder on a tall 2 x 5-header and corresponding 2 x 5-pin socket.

This will work fine in the single-band case. The bravery is only required when you already have the

relay-switched installed, which already has header pins soldered. You could solder a header socket

to the top side of the relay PCB, but it will be necessary to trim the wires of the header a little, since

you will not be able to properly fit the header socket pins into the relay PCB, because the holes are

already in use. Since there are only two wires it will probably be easiest just to use wiring rather than

a plug/socket solution.

The RF connections between boards can be thin coax, but don’t worry if none is available and you

just need to use a piece of hook-up wire.

The envelope control signals allow the Ultimate3S to send 8-bit values to the DAC, which controls the

PA power modulator, so that the Ultimate3S firmware can create a precise raised cosine envelope

shape. These control signals do not need to be connected if you are constructing the HF PA

kit according to the “simplified assembly instructions” – in this case you are not building the

power modulator and you have already decided you don’t care about raised cosine envelope

shaping. The connections are as follows:

1) Connect the “D” pad on the PA PCB to the “D4” pad at the LCD header on the U3S PCB

2) Connect the “RCK” pad on the PA PCB to the “R” pad on the U3S PCB

3) Connect the “SCK” pad on the PA PCB to the “D5” pad at the LCD header on the U3S PCB

The shift register “D” (data) and “SCK” (clock) signals are shared with LCD control signals. This

means that when data is written to the LCD, the shift register is also loaded at the same time.

However there is no conflict here, since the shift register contents are not reflected at its output until

the “RCK” pin receives a pulse. The RCK signal is connected to the “R” pad on the Ultimate3S which

is not shared with anything else. So there is no problem with sharing the other two signals with LCD

control lines.

Rev 1.01 6

5. Ultimate3S configuration

This section applies if you are using the full 5W HF PA kit assembly, including the raised cosine

envelope shaping. The Ultimate3S requires at least firmware version v3.12.

There is a configuration screen as follows:

Shaping {ms Max}

05 115

The first parameter is the rise/fall time of the raised

cosine envelope that will be generated. In this

example it is 5ms. Rise/fall times of around 5 to

10ms are common in commercial amateur radio

CW transceivers.

The second parameter is the maximum value to

send to the DAC. A safe value would be 115 for a

12V supply or 140 for a 13.8V supply. Please refer

to the PA Assembly instructions, section 5.3, for an

explanation of this value and for values that suit

other PA supply voltages. If you have an

oscilloscope you can experiment with different

values.

The ‘scope screenshot (right) is a perfect raised cosine 12wpm CW dit with 20ms rise and fall times.

If the “Max” value is too high (above left), then there will be clipping (a sharp corner) at the start and

finish of the transmission, and there will be a delay from key-up to the decline of the RF envelope. On

the other hand if the “Max” value is too low (above right) then the envelope will have a nice raised

cosine shape but will have a reduced amplitude (power output).

Rev 1.01 7

6. References

For updates relating to the PA kit please visit the QRP Labs PA Kit page http://qrp-labs.com/pa

Refer to the PA Assembly instructions, download at the PA Kit page http://qrp-labs.com/pa

For any questions regarding the assembly and operation of this kit please join the QRP Labs

group, see http://qrp-labs.com/group for details

7. Document Revision history

1.0 First version, 03-Jan-2017

1.01 Corrected typo in the description in section 5

Andere Handbücher für Ultimate3S

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere QRP Labs Mikrocontroller Handbücher

QRP Labs

QRP Labs Ultimate3S Bedienungsanleitung

Beliebte Mikrocontroller Handbücher anderer Marken

AMS

AMS AS7261 Demo Kit Bedienungsanleitung

Novatek

Novatek NT6861 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266 SDK Einrichtungshandbuch

Nuvoton

Nuvoton ISD61S00 ChipCorder Leitfaden

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Bedienungsanleitung

Texas Instruments

Texas Instruments Chipcon CC2420DK Bedienungsanleitung

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Bedienungsanleitung

NEC

NEC 78GK0S/K 1+ Series Montage- und Bedienungsanleitung

Mikroe

Mikroe SEMITECH N-PLC Click Montage- und Bedienungsanleitung

Intel

Intel Agilex Bedienungsanleitung

Cypress

Cypress CY4607 HX2VL Bedienungsanleitung

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Bedienungsanleitung

Texas Instruments

Texas Instruments TMS320F2837 D Series Bedienungsanleitung

CYPRES

CYPRES CY14NVSRAMKIT-001 Bedienungsanleitung

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266EX Betriebsanleitung

Abov

Abov AC33M8128L Bedienungsanleitung

Laird

Laird BL654PA Bedienungsanleitung