QSC AcousticDesign Series Gebrauchsanweisung

Hardware User Manual

AcousticDesign™ Series Direct Weather Landscape Loudspeakers

AD-DWL.180

AD-DWL.360

AD-DWL.SUB

AD-DWL.BASE

TD-001650-01-A

*TD-001650-01*

EXPLANATION OF TERMS AND SYMBOLS

The term “WARNING!” indicates instructions regarding personal safety. If the instructions are not followed the result may be bodily

injury or death.

The term “CAUTION!” indicates instructions regarding possible damage to physical equipment. If these instructions are not followed, it

may result in damage to the equipment that may not be covered under the warranty.

The term “IMPORTANT!” indicates instructions or information that are vital to the successful completion of theprocedure.

The term "NOTE" is used to indicate additional useful information.

The lightning ﬂash with arrowhead symbol in a triangle alerts the user to the presence of uninsulated dangerous voltage within

the product’s enclosure that may constitute a risk of electric shock to humans.

The exclamation point within a triangle alerts the user to important safety, operating, and maintenance instructions in this

manual.

IMPORTANT SAFETY INSTRUCTIONS

WARNING!: While it is possible for one person to lift a loudspeaker, it is important to use proper lifting techniques.

Suggested reading: OSHA Technical Manual (OTM) > Back Disorders and Injuries:

https://www.osha.gov/otm/

1. Keep these instructions.

2. Heed all warnings.

3. Follow all instructions.

4. Clean only with a damp cloth.

5. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliﬁers) that produce

heat.

6. Only use attachments/accessories speciﬁed by the manufacturer.

7. Refer all servicing to qualiﬁed service personnel.

8. Adhere to all applicable, local codes.

9. Consult a licensed, professional engineer when any doubt or questions arise regarding a physical equipment installation.

Environmental

• Operating Temperature Range: -30°C to 50°C

• Relative Humidity: 0 to 100% RH, non-condensing

Speciﬁcations and Dimensions

Product speciﬁcations and dimension drawings for the AD-DWL Series can be found online at qsys.com.

RoHS Statements

The QSC AD-DWL loudspeakers are in compliance with European Directive 2011/65/EU – Restriction of Hazardous Substances

(RoHS2).

The QSC AD-DWL loudspeakers are in compliance with “China RoHS” directives per GB/T24672. The following table is provided for

product use in China and its territories.

QSC AD-DWL Loudspeakers

部件名称

(Part Name)

有害物质

(Hazardous Substances)

铅

(Pb)

汞

(Hg)

镉

(Cd)

六价铬

(Cr(vi))

多溴联苯

(PBB)

多溴二苯醚

(PBDE)

电路板组件

(PCB Assemblies)

X O O O O O

机壳装配件

(Chassis Assemblies)

X O O O O O

本表格依据 SJ/T 11364 的规定编制。

O: 表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量要求以下。

X: 表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 规定的限量要求。

（目前由于技术或经济的原因暂时无法实现替代或减量化。）

This table is prepared following the requirement of SJ/T 11364.

O: Indicates that the concentration of the substance in all homogeneous materials of the part is below the relevant threshold

speciﬁed in GB/T 26572.

X: Indicates that the concentration of the substance in at least one of all homogeneous materials of the part is above the

relevant threshold speciﬁed in GB/T 26572.

(Replacement and reduction of content cannot be achieved currently because of the technical or economic reason.)

• (1) AD-DWL.180, AD-DWL.360, or AD-DWL.SUB

• (1) collar

• (4) collar Torx M6 screws

• (1) Torx bit

• (1) installation template

• (1) paint mask for AD-DWL.180, (2) paint masks for

AD-DWL.360*

* Paint mask not required for AD-DWL.SUB. For painting

instructions, see the Self Help Portal.

Four M10 or 3/8” bolts

on 120mm (4.72”) diameter circle

— Figure 1 —

Installation on Concrete or Other Hard Surfaces

Hard surface installation requires four M10 or 3/8" drop-in anchor

bolts, eight nuts, and eight washers (not supplied). The bolts must be

long enough to provide 65mm (2.5") of usable thread above the

surface level.

Prepare the surface

NOTE:

Before proceeding, be aware of the location of

conduit under the loudspeaker location and the intended

orientation of the loudspeaker – for example, facing

parallel to another hard surface, such as a sidewalk or

patio.

1. Use the supplied installation template to mark the location for the

four drop-in anchor bolts as close to the center of each arc as

possible, as shown in Figure 1.

2. Install the anchor bolts (not supplied) into the mounting surface.

Mount the collar

The rotational orientation of the collar determines the

aim of the loudspeaker. The collar can rotate ± 26°

from the arc center.

1. On each anchor bolt, place a bottom nut and

washer. These are used to level the collar.

2. Place the collar on the bottom washers. Using a

bubble level, adjust the nuts so that the collar is

horizontal and that all washers are in contact with

the collar ﬂange. See Figure 2.

NOTE:

There must be no gap between the

washers and the collar ﬂange.

3. Rotate the collar to the exact desired position,

verify levelness, and then secure the collar by

attaching a top washer and nut for each bolt. See

Figure 3.

4. Tighten all top nuts to a recommended torque of

81 kgf.cm (70 lbf.in).

Hard Surface

Flange

Nut Washer

— Figure 2 —

Hard Surface

Flange

Nut

Washer

— Figure 3 —

What's in the Box

Concrete/Surface Installation – Continued

Wire the loudspeaker

1. Lay the loudspeaker on the ground with its open base near the installed collar.

2. Make a solid and waterproof connection between the loudspeaker's wire pig-

tail and the output from your ampliﬁer, with red being positive (+) and black

being negative (-). Wire in parallel to other AD-DWL Series loudspeakers as

needed. See Figure 4.

NOTE:

Gel-ﬁlled wire nuts, WAGO gel boxes, or equivalent are

recommended for wire connections.

3. Adjust the Transformer Settings dial to the desired setting for your installation,

depending on your AD-DWL Series model:

AD-DWL.180 and AD-DWL.360 (Figure 5), AD-DWL.SUB (Figure 6).

Attach the loudspeaker

1. Tuck the wires into the hollow loudspeaker base.

2. Lower the loudspeaker onto the collar and attach them together

with the four supplied M6 Torx screws. See Figure 7.

3. Tighten the screws to a recommended torque of 23 kgf.cm (20

lbf.in).

— Figure 5 — — Figure 6 —

Four M6 Torx

screws

— Figure 7 —

— Figure 4 —

Ampliﬁer

++ + +

__ _ _

In-Ground Installation

In-ground installation requires the AD-DWL.BASE* accessory, which comes with all the hardware needed (bolts, nuts, and washers) to

mount the loudspeaker collar to the BASE.

Prepare the BASE

Remove the side knockouts as needed to allow for attaching conduit for the speaker wiring between the loudspeakers and ampliﬁer.

Refer to Figure 8 for an example.

NOTE:

Conduit knockouts in the AD-DWL.BASE accommodate standard 12mm (3/8") conduit clamps.

Grade Level

3/8” Conduit

From Ampliﬁer

To Other

Speakers

— Figure 8 —

Auger Stake

(optional, not supplied)

— Figure 9 —

Install the BASE

NOTE:

Keep the disposable round lid attached to the top of the BASE during

installation to prevent debris from entering the cavity.

1. For each BASE unit, dig a hole at least 275mm (11") deep and 200mm (8") in diameter.

2. Run conduit and wiring as needed.

3. Place the BASE into the hole, ensuring that the top of the BASE is ﬂush with grade level. To

assist with stabilizing the BASE in soft or unstable soil, you can optionally attach an auger

stake (not supplied) through the bottom knockout, as shown in Figure 9.

NOTE:

Before proceeding, ensure that the BASE is oriented such that a pair of

bolts is parallel with the intended aim of the loudspeaker tweeter – for example,

facing a surface such as a sidewalk or patio. See Figure 10.

4. Fill the hole surrounding the base with soil or concrete. Compress the soil to help prevent

movement of the BASE and loudspeaker. (Adding water to the backﬁll can help with this.)

For a more secure installation, optionally anchor the BASE by pouring concrete around its

body – up to 90% of the BASE's overall height.

Tweeter

Tweeter BASE

— Figure 10 — *AD-DWL.BASE accessory has not been evaluated by UL.

In-Ground Installation – Continued

Mount the collar

The rotational orientation of the collar (Figure 11) determines the

aim of the loudspeaker. The collar can rotate ± 26° from the arc

center.

NOTE:

Refer to Figure 12 for proper placement of the

nuts and washers described in the following steps.

1. Remove the top nuts and washers from each of the four BASE

bolts and set them aside.

2. Discard the protective lid.

3. Thread the bottom nuts and washers all the way down to the

Nyloc nuts. (Do not loosen the Nyloc nuts at the base of the

bolts, as these secure the bolts in place.)

4. Place the collar on the bottom washers of the BASE. Using a

bubble level, adjust the nuts so that the collar is horizontal and

that all washers are in contact with the collar ﬂange. See Figure

13 .

NOTE:

There must be no gap between the washers and

the collar ﬂange.

5. Rotate the collar to the exact desired position, verify levelness,

and then secure the collar by attaching a top washer and nut for

each bolt.

6. Tighten all top nuts to a recommended torque of 81 kgf.cm (70

lbf.in).

Collar

Top Nuts and

Washers

Collar

Bottom Nuts

and Washers

BASE

— Figure 11 —

— Figure 12 —

Flange

Nyloc Nuts

(Do not loosen)

Top Nuts and Washers

Bottom Nuts and Washers

Grade Level BASE

— Figure 13 —

In-Ground Installation – Continued

Wire the loudspeaker

1. Lay the loudspeaker on the ground with its open base near the installed collar.

2. Make a solid and waterproof connection between the loudspeaker's wire

pig-tail and the output from your ampliﬁer, with red being positive (+)

and black being negative (-). Wire in parallel to other AD-DWL Series

loudspeakers as needed. See Figure 14.

NOTE:

Gel-ﬁlled wire nuts, WAGO gel boxes, or equivalent are

recommended for wire connections.

3. Adjust the Transformer Settings dial to the desired setting for your installation,

depending on your AD-DWL Series model:

AD-DWL.180 and AD-DWL.360 (Figure 15), AD-DWL.SUB (Figure 16).

Attach the loudspeaker

1. Tuck the wires into the hollow loudspeaker base.

2. Lower the loudspeaker onto the collar and attach them together

with the four supplied M6 Torx screws. See Figure 17.

3. Tighten the screws to a recommended torque of 23 kgf.cm (20

lbf.in).

— Figure 15 — — Figure 16 —

Four M6 Torx

screws

— Figure 17 —

— Figure 14 —

Ampliﬁer

++ + +

__ _ _

Self Help Portal

Read knowledge base articles and discussions, download software and ﬁrmware, view product documents and training videos, and

create support cases.

qscprod.force.com/selfhelpportal/s/

Customer Support

Refer to the Contact Us page on the Q-SYS website for Technical Support and Customer Care, including their phone numbers and

hours of operation.

qsys.com/contact-us/

Warranty

For a copy of the QSC Limited Warranty, go to:

qsys.com/support/warranty-statement

and other countries. Patents may apply or be pending. All other trademarks are the property of their respective owners.

qsc.com/patents

qsys.com/patents

Andere Handbücher für AcousticDesign Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere QSC Sprecher Handbücher

QSC

QSC K8.2 Bedienungsanleitung

QSC

QSC Acoustic Design Series Bedienungsanleitung

QSC

QSC LF4215-F Bedienungsanleitung

QSC

QSC AD-S282H Bedienungsanleitung

QSC

QSC LA108 Bedienungsanleitung

QSC

QSC SR-110 Bedienungsanleitung

QSC

QSC ILA System v2 Bedienungsanleitung

QSC

QSC AP-5102 Bedienungsanleitung

QSC

QSC SR-1000 Bedienungsanleitung

QSC

QSC AcousticDesign AD-S10T Bedienungsanleitung

QSC

QSC ACE 540 Bedienungsanleitung

QSC

QSC ACE 1250 Bedienungsanleitung

QSC

QSC AD-C42T Bedienungsanleitung

QSC

QSC AcousticDesign Bedienungsanleitung

QSC

QSC AcousticDesign AD-P6T Bedienungsanleitung

QSC

QSC LA112-KIT-SA Bedienungsanleitung

QSC

QSC AC-S4T Bedienungsanleitung

QSC

QSC K10 Bedienungsanleitung

QSC

QSC AC-C4T Bedienungsanleitung

QSC

QSC AD-C42T Bedienungsanleitung

QSC

QSC KLA12 Bedienungsanleitung

QSC

QSC LF-4315 Bedienungsanleitung

QSC

QSC AcousticDesign AD-S32T Bedienungsanleitung

QSC

QSC SR-1590 Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung