QSFPTEK S5300-48P6X Bedienungsanleitung

www.qsfptek.com v1.0

1 / 10

V1.0

S5300-48P6X Quick Start Guide

48-Port Gigabit Ethernet L2++ PoE+ Switch

48x PoE+ Ports, with 6x 10GE SFP+, Support Stacking

www.qsfptek.com v1.0

2 / 10

Introduction

The QSFPTEK S5300-48P6X is a next-gen aggregation switch, with 48x GE RJ45, 6x 10GE SFP+ Uplink. It supports stacking of up to

8 S5300 series switches, making them logically regarded as one switch for interconnection and management.

We appreciate your decision to select S5300-48P6X. This manual is intended to help you become acquainted with the switch design

and provide instructions for implementing the switches into your network.

Accessories

Hardware Overview

www.qsfptek.com v1.0

3 / 10

Front Panel Ports

Ports

Description

Gigabit port

RJ45 port, LINK/ACT indicators

10GE port

SFP+ port, LINK/ACT indicators

CON Port

A baud rate of 9600bps, RJ45 port

Front Panel LEDs

LEDS

Description

SWAP

Swap function, used to switch POE indication.

PWR LED

If the switch is powered on, the PWR indicator is on.

SYS LED

If the system is started normally, the SYS indicator flickers.

POE LED

Indicates whether the POE card is detected.

Back Panel

www.qsfptek.com v1.0

4 / 10

Abbrev

Name

Description

POWER

DC power supply

Input voltage 55VDC

Grounding column

The grounding must be fine.

ON/OFF

Power on-off

ON: means the power is on;

OFF: means the power is off.

POWER

AC power supply

Input voltage AC100-240V

Installation Requirements

Tools Preparation

Screwdriver

Static-proof wristband

Bolt

Ethernet cable

Other Ethernet terminal devices

Control terminal

Safety Principles

Keep dustless and clean during or after the installation.

Put the cover at the safe place.

Put tools at the right place where they are not easily falling down.

Put on relatively tight clothes, and fasten the tie or scarf well and roll up the sleeve, avoiding stumbling the machine box.

Put on the protective glasses if the environment may cause damage to your eyes.

Avoid incorrect operations that may cause damage to human or devices.

Site Environment

Make sure that the workshop is well-ventilated, the heat of electrical devices is well-discharged

Avoid to damage devices by following the electrostatic discharge prevention procedure. S5300-48P6X Hardware Installation

Manual

Put the machine box at the place where cool air can blow off the heat inside the machine box. Make sure the machine box is

sealed.

Mounting the Switch

Connecting the Power

www.qsfptek.com v1.0

5 / 10

1. Plug the AC power cord to the switch power port on the back rear.

2. Connect the other end of the power cord to a AC power source equipment.

Connecting the RJ45 Port

1. Connect one end of the Ethernet cable to the RJ45 port on networking equipment, such as PC, printer, server, storage, etc.

www.qsfptek.com v1.0

6 / 10

2. Connect the other end of the Ethernet cable to the switch RJ45 port.

Connecting the SFP+ Port

1. Insert the SFP+ module into the SFP+ port.

2. Plug a fiber patch cable to the SFP+ transceiver.

3. Connect the other end of the fiber to the device that you want to realize data communication.

www.qsfptek.com v1.0

7 / 10

Connecting the Management Ports

Connecting the Console Port

1. Prepare an console cable.

2. Insert the RJ45 connector of the console cable into the console port on the switch.

3. Connect the D89 female connector on the other end of the console cable to the serial port on the computer host.

Configuring the Switch

Configuring the Switch Using the Web-based Interface

Step 1: Connect your computer to the switch using an Ethernet cable and open a web browser.

Step 2: Set the IP address of the computer to 192.168.0.x (where "x" is any number from 2 to 254) and the subnet mask to

255.255.255.0.

www.qsfptek.com v1.0 8 / 10

Configuring the Switch Using the Console Port

Step 1: Use the console cable to direct connect the switch console port to your computer.

Step 2: Launch the terminal simulation software such as Hyper Terminal on the computer.

Step 3: Configure the parameters of the terminal emulation software as follows: 9600 bits per second, 8 data bits, no parity, 1 stop bit,

and no flow control

Step 3: Open a web browser and type http://192.168.0.1 in the address bar. Enter the default username and password (admin/admin)

.Step 4: Click sign-in to access the web-based configuration page.

www.qsfptek.com v1.0

9 / 10

Step 4: Enter the default username and password (admin/admin).

Troubleshooting

Hardware Fault Analysis

Power and cooling systems—power and fan

Port, cable and connection—ports on the front panel of the switch and the cables connecting these ports

Faults Relative with Power and Cooling System

Do the following checkups to help remove the fault:

1. When the power on-off is at the “ON” location, check whether the fan works normally. If the fan does not work well, check the fan.

2. If the switch is too hot, check whether the air outlet and air inlet are clean and then do relative operations in section 2.3

“Requirements for Common Locations”.

3. If the switch cannot be started and the PWR indicator is off, check the power.

Faults Relative with Port, Cable and Connection

Do the following checkups to help remove the fault:

If the port of the switch cannot be linked, check whether the cable is correctly connected and whether the peer connection is normal.

If the power on-off is at the “ON” location, check the power source and the power cable.

If the CLI port does not work after the system is started up, check whether the CLI port is set to a baud rate of 9600 bps, eight data bits,

no sum check bit, one stop bit and no traffic control.

www.qsfptek.com v1.0

10 / 10

Support and Other Resources

Contact us https://www.qsfptek.com/company/contact-us.html

Email sales@qsfptek.com

Customer Success https://www.qsfptek.com/resources/customer-success-stories

Product Warranty

S5300 series switches are backed by a 5-year limited warranty supported by QSFPTEK. And you are eligible to apply for a return or

exchange of your items within 14 days of receiving them.

For more details about applying qualifications, please live chat or email

sales@qsfptek.com

for support.

5 Year Warranty 14-day Return Window

Inhaltsverzeichnis

Andere QSFPTEK Schalten Handbücher

QSFPTEK

QSFPTEK S5300-24S8T6X Bedienungsanleitung

QSFPTEK

QSFPTEK S7300-48TE4X2Q Bedienungsanleitung

QSFPTEK

QSFPTEK S5300-24T6X Bedienungsanleitung

QSFPTEK

QSFPTEK S7600-24X2C Bedienungsanleitung

QSFPTEK

QSFPTEK S5300-24P4TS Bedienungsanleitung

QSFPTEK

QSFPTEK S5300-48T4X Bedienungsanleitung

QSFPTEK

QSFPTEK S5300-8P2S Bedienungsanleitung

QSFPTEK

QSFPTEK S5600-24T8X Bedienungsanleitung

QSFPTEK

QSFPTEK S5300-16S8TS4X Bedienungsanleitung

QSFPTEK

QSFPTEK S5300-48T6X Bedienungsanleitung

QSFPTEK

QSFPTEK S7600-48Y8C Bedienungsanleitung

QSFPTEK

QSFPTEK S5300-24TE6X-P Bedienungsanleitung

QSFPTEK

QSFPTEK S5300-24T4S Bedienungsanleitung

QSFPTEK

QSFPTEK S5300-48M6X Bedienungsanleitung

QSFPTEK

QSFPTEK S5300-24T4X Bedienungsanleitung

QSFPTEK

QSFPTEK S7600-24X2Q Bedienungsanleitung

QSFPTEK

QSFPTEK S7300-24X2C Bedienungsanleitung

QSFPTEK

QSFPTEK S7600-24Y4C Bedienungsanleitung

QSFPTEK

QSFPTEK S5600-48T4X Bedienungsanleitung

QSFPTEK

QSFPTEK S7300-48X2Q4C Bedienungsanleitung

QSFPTEK

QSFPTEK S5310-48P6X Bedienungsanleitung

QSFPTEK

QSFPTEK S5600-48S4X Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung