QTek 9000 Bedienungsanleitung
Pocket
Quick Start Guide
2 |
Q.1 What’s in the Box?
Pocket PC Phone
USB Cable
AC Adapt
User Manual
Quick Start Guide
User Manual
and Quick Start Guide
Headset
Battery
Getting Started CD
| 3
Front, and Back View
1 Speaker Listen to audio media or a phone call from here.
2 Camera Button Press to launch the camera. Press again to take a picture.
3 Voice Recorder/
Voice Recognition
Press to record a voice note or load the voice recognition program.
4 Infrared Port Lets you exchange file(s) or data with other devices wirelessly.
5 Backlight Press to turn on the backlight.
6 Volume Slide left or right to adjust the volume.
7 Send/Speakerphone Press to take an incoming call, or to dial a number. Keep pressed for one
second to activate Speakerphone.
8 End Press to end a call.
9 Stylus and Stylus Slot
10 WCDMA Car Antenna
Connector
You can connect your WCDMA phone to a car antenna to utilize the superior
reception quality.
11 GSM Car Antenna
Connector
You can connect your GSM phone to a car antenna to utilize the superior
reception quality.
12 Sync Connector Use this connector for synchronizing data or recharging the battery.
13 Soft Reset With the stylus, press the Reset button to soft-reset your device.
14 Earphone Jack Allows you to listen to audio media or use the phone’s hands-free kit.
12 13 149 1110
7
8
1
5 6
2 3 4
Front View
Back View
4 |
Top, Bottom, and Left Side View
23
24
25
15
16
17
Left Side View
18
19
20
22
21
Top View
Bottom View
| 5
15 Power/Backlight Press to turn on your device or backlight.
16 Microphone Speak into the microphone when receiving or making a phone call or voice
recording.
17 MMC/SD Cards or
SDIO Accessories Slot
Lets you insert a storage card (MMC/SD) for storing data.
18 Touch Screen Use to write, draw, or make a selection with the stylus.
19 Navigation Pad Press this multi-directional control up, down, left, or right to move through
menus, program instructions; carry out the selection by pressing the center
button.
20 Video Camera Lens
21 Notification LED Bi-color LED on the right side: Green and Orange for GSM or WCDMA standby,
SMS message, GSM or WCDMA network status, notification, battery charging
status.
Bi-color LED on the left side: Blue and green for Bluetooth system notification
of powered-up and ready to transmit radio frequency signal, and Wi-Fi status.
22 Light Sensor When you use the device in a dark environment, the system will turn on
keyboard backlight as you press any key.
23 Camera Lens
24 Fixing Lock Press to release the back cover.
25 Flash Light
6 |
Q.2 Getting your Device Ready
Before you start using your device, you must install a SIM card and a charged battery on
your device.
Install the SIM card
Follow these steps to install a SIM (Subscriber Identity Module) card provided by your local
network service provider that contains your phone number, service details, and phonebook/
message memory.
Locked Unlocked
Note Ensure the device is in the sleep mode before you install the USIM or SIM card.
1. Remove the back cover by pressing the fi xing lock.
2. Push the red battery lock down to unlock the battery pack.
3. Press the clip on the right side to remove the battery.
| 7
4. Insert the SIM card into the SIM card slot with its gold contacts facing down. Its cut-off
corner should match the cut-off corner in the slot. Push down lightly and forward to
snap it into place.
5. Replace the battery and gently push down to snap it into place.
6. Push the red battery lock back up to lock the battery.
7. Replace the cover; slide it back on, and then push down lightly at the bottom to snap it
securely into place.
Based on the SIM card installed, the device displays either the G or 3G icon. Installing a
valid GPRS/GSM SIM card displays the G icon if the device is in the second-generation
network coverage area. If the SIM is 3G enabled and the phone is in 3G WCDMA coverage,
the 3G icon will be displayed.
Charge the battery
New batteries are shipped partially charged. It is recommended that you charge the battery
to its maximum capacity or for at least 8 hours before you start using your device.
You can charge the battery while your device is turned on or off. Plug the AC adapter into the
Sync connector on the back side of the device.
8 |
When your device is turned off, charging is indicated by a solid amber light on the LED
indicator. When your device is turned on, charging is indicated by a solid amber light on the
LED indicator as well as a charging icon on the device screen. A green light on the LED
indicator or a charged icon on the device screen indicates that charging is complete.
You can also charge the battery by plugging the sync cable into the USB port on PC.
When the battery power gets very low, your device screen displays a warning message.
When you see this, immediately save your data by synchronizing with your PC, or save your
data on a secondary storage card, and then turn off your device. Do not try to restart your
device until you have connected your device to an external power supply.
Turn on your device
Press POWER to turn on your device. When you turn on the device for the first time, you are
asked to complete a screen calibration process. To turn off the device, press POWER again.
| 9
Q.3 Making a Voice or Video Call
To make a phone call, ensure that a SIM card is installed and the battery is sufficiently
charged. To open the Phone screen, press SEND or tap Phone on the Today screen.
Make a Voice Call
• On the Phone screen, enter the number you want to call
and tap Talk. To end the call, tap End.
Make a Video Call
• On the Phone screen, enter the number you want to call
and tap Video. To end the call, tap End.
Note The caller’s image will appear on the screen about 3 to 5
seconds after connection, depending on the signal strength.
The streaming images quality may also be influenced by the
signal.Video calls are only possible when within 3G coverage.
Phone Screen
Video Call
10 |
Q.4 Synchronizing Outlook Information
Using ActiveSync, you can synchronize information on your device with information on
your PC, such as Outlook content. ActiveSync is already installed on your device, but you
need to install it on your PC if you don’t already have it. Insert the Getting Started CD into
the CD drive of your PC. Follow the instructions on the installation wizard screen to install
ActiveSync. Once installation is completed, connect the sync cable to the device and plug it
into your PC’s USB port, shown in the illustration below on the left.
To set up a partnership between the device and the PC, turn on your device. When the PC
detects a USB connection, it starts the ActiveSync Synchronization Setup Wizard. Follow the
instructions on the screen and select the Outlook items you want to synchronize.
Synchronization Setup Wizard
Andere Handbücher für 9000
2
Inhaltsverzeichnis
Andere QTek Handheld Handbücher
