Qualcast 46 cc Petrol Chainsaw Bedienungsanleitung
AQG-PC 4645
Petrol Chain Saw Artikel-Nr.: 4501662
Ident-Nr.: 11011
Komponenten / Ersatzteile
Position Artikel-Nr. Beschreibung Position Artikel-Nr. Beschreibung
1 450166001001 oil tank
3 450166001003 safty trigger lever
4 450166001004 rear handle cover
5 450166001005 trigger
6 450166001006 trigger spring ›0.9
7 450166001007 pin
10 450166001010 special screw ST4.8x15
13 450166001013 vacuum hose spring ›6
14 450166001014 fuel pipe
16 450166001016 oil filter
18 450166001018 oil cap
19 450166001019 oil cap gasket
21 450166001021 screw ST4.8x16
22 450166001022 right rubber gasket for handle
23 450166001023 bottom rubber gasket for handl e
24 450166001024 handle
Komponenten / Ersatzteile
Position Artikel-Nr. Beschreibung Position Artikel-Nr. Beschreibung
28 450166001028 heat insulation plate
29 450166001029 flange inlet
30 450166001030 carburetor
31 450166001031 carburetor gasket
37 450166001037 air filter washer ›1.5x›22
38 450166001038 air filter
40 450166001040 air filter knob für Luftfilterabdeckung
41 450166001041 knob gasket
42 450166001042 air filter top cover
43 450166001043 cover
47 450166001047 tension spring for clutch ›5.3 x150
48 450166001048 clutch gasket
49 450166001049 clutch drum
50 450166001050 sproket wheel
51 450166001051 needle bearing K121514.5
52 450166001052 worm wheel
54 450166001054 oil pump cover für Ölpumpe
55 450166001055 oil seal ›15x›28x5
56 450166001056 bearing 6202
59 450166001059 throttle rod
64 450166001064 seal mat
65 450166001065 spark plug L8RTF
66 450166001066 retaining ring
68 450166001068 intake tube seal gasket
69 450166001069 cylinder seal gasket
70 450166001070 snap ring for piston pin ›11
71 450166001071 piston pin ›11x34.3
72 450166001072 piston ring ›43.5
73 450166001073 piston ›43.5
84 450166001084 circlip ›35
85 450166001085 oil seal ›15x›35x5
86 450166001086 Oil seal plate
88 450166001088 hex nut M8x1
89 450166001089 spring washer ›8
90 450166001090 flywheel
93 450166001093 engine oil cap
94 450166001094 seal ring
97 450166001097 ignitor
98 450166001098 ignitor cap
107 450166001107 muffler
108 450166001108 muffler cover
109 450166001109 muffler gasket
111 450166001111 cyliner
116 450166001116 toothed plate
122 450166001122 oil fiter
123 450166001123 oil-inlet pipe
125 450166001125 oil pump
126 450166001126 oil-outlet pipe
127 450166001127 tower spring
129 450166001129 chain catcher
173 450166001173 file ›4.5
174 450166001174 allen key T4
175 450166001175 allen key T3
176 450166001176 plug wrench
177 450166001177 screwdriver
180 450166001180 bar cover
800 450166001800 mix bottle
901 450166001901 starter assy.
902 450166001902 brake assy.
903 450166001903 retainer with fly weights set
Important - Please read these instructions fully before starting assembly
These instructions contain important information that will help you get the best from
your chainsaw, ensuring it is assembled correctly and safely.
If you need help or have damaged or missing parts, call the Customer Helpline
on 0151 649 1500.
Qualcast
46 cc Petrol Chainsaw
Original Operating Instructions
Feb 2011
UK/Ireland 0151 649 1500
Republic of Ireland 1890 946 244
Web www.einhell.co.uk
After Sales Support
Operation and Maintenance Manual
Contents
2
Customer Helpline 0151 649 1500
Components List.......................................................................................................................................... 4-5
Safety Information ...........................................................................................................................................6
Warnings Symbols ......................................................................................................................................6
Explanation of the Symbols and Warning signs on the machine labels.............................................. 7-8
General Safety .............................................................................................................................................9
Personal Safety............................................................................................................................................9
Operating and Maintenance Safety .........................................................................................................10
Handling Safety ........................................................................................................................................11
Proper Use .......................................................................................................................................... 12-13
Kickback Safety.........................................................................................................................................13
Pinching Safety..........................................................................................................................................14
Preparing to Operate the Chainsaw.........................................................................................................15
Step 1 - Assemble the Chainsaw..............................................................................................................15
Step 2 - Check the Chain Brake ......................................................................................................... 15-16
Step 3 - Fuel and Lubrication ............................................................................................................. 17-18
Step 4 - Filling the Fuel Tank ....................................................................................................................19
Step 5 - Filling the Chain Lubrication Oil Tank ........................................................................................20
Operating the Chainsaw................................................................................................................................21
Step 1 - Starting the Engine ............................................................................................................... 21-26
Step 2 - Restarting the Chainsaw When Warmed Up.............................................................................27
How to Use the Chainsaw.............................................................................................................................28
Introduction................................................................................................................................................28
Felling ................................................................................................................................................... 29-30
Limbing ......................................................................................................................................................31
Bucking ......................................................................................................................................................32
Contents
3
Customer Helpline 0151 649 1500
Storing the Chainsaw ....................................................................................................................................33
Step 1 - Storing the Chainsaw for Short Periods ....................................................................................33
Step 2 - Storing the Chainsaw for Extended Periods ...................................................................... 33-35
Step 3 - Preparing the Chainsaw for Use Following Storage ................................................................35
Maintenance...................................................................................................................................................36
Maintenance Schedule .............................................................................................................................36
Step 1 - Operational Chain Brake Test ....................................................................................................37
Step 2 - Clean / Replace the Air Filter ............................................................................................... 38-39
Step 3 - Change / Replace the Fuel Filter ......................................................................................... 40-42
Step 4 - Clean / Replace the Spark Plug ........................................................................................... 42-46
Step 5 - Carburettor Settings ...................................................................................................................47
Step 6 - Lubricating the Sprocket Tips.............................................................................................. 47-48
Step 7 - Reversing the Guide Bar.............................................................................................................49
Step 8 - Adjusting the Automatic Chain Lubricator ................................................................................49
Step 9 - Check the Saw Chain Tension....................................................................................................50
Step 10 - Sharpening the Saw Chain .......................................................................................................51
Troubleshooting .............................................................................................................................................52
General Troubleshooting..................................................................................................................... 51-53
Useful Information .........................................................................................................................................53
Technical Data ...............................................................................................................................................54
Technical Data Table .................................................................................................................................54
Disposal..........................................................................................................................................................54
Disposal Instructions ................................................................................................................................54
Guarantee ......................................................................................................................................................55
Declaration of Conformity .............................................................................................................................56
4
Customer Helpline 0151 649 1500
Saw chain
Chain bar
Chain brake lever/
front hand guard
Air filter cover
Safety lock
Rear handle/
bootstrap
Throttle lever
Chain
tensioning screw
Bar fastening nut
Chain catch
Stop claw
Chain guard
Components List
5
Customer Helpline 0151 649 1500
Choke/
(carburettor setting)
Spark plug
(under the air
filter cover)
Starter handle
Front handle
Oil tank cap
Fan housing
Fuel tank cap
Stop switch
Components List
Safety Information
6
Important - Please read these instructions fully before operating or maintaining
Customer Helpline 0151 649 1500
The following warning symbols appear throughout this assembly manual and indicate the appropriate
safety measures you should take when assembly and operating the chainsaw.
This symbol indicates there is a danger of serious personal injury or death if you do not observe
the warning.
This symbol indicates that there is: -
1. Danger of permanently damaging your hearing if you do not wear ear defenders
2. Danger of permanently damaging your sight if you do not wear suitable goggles or glasses
3. Danger of suffering serious head injuries if you do not wear a suitable helmet
This symbol indicates that there is a danger of damaging your hands if you do not wear thick, hard
wearing gloves.
This symbol indicates that there is a danger of damaging your feet if you do not wear protective shoes
or boots.
This symbol indicates there is a danger of serious personal injury if you attempt to make adjustments
to the chainsaw while it is running.
This symbol indicates there is a risk of explosion if you do not observe the warning.
This symbol indicates there is a risk of igniting flammable liquids if you do not observe the warning.
This symbol indicates there is a danger of serious personal injury if you attempt to grasp or come into
contact with a moving saw chain.
This symbol indicates there is a danger of kickback if you fail to observe this warning.
Warnings Symbols
Safety Information
Important - Please read these instructions fully before operating or maintaining
7Customer Helpline 0151 649 1500
Explanation of the Symbols and Warning signs on the machine
Explanation of the symbols on the warning label on the machine.
Read the user manual before using the machine.
On all jobs performed with the saw you must always wear safety goggles to guard your eyes from flying
materials/objects and ear defenders to protect your hearing. Wear a safety helmet if there is a risk of
objects falling on you from above.
Important! Wear gloves to protect your hands.
Wear safety shoes to protect your feet.
Warning! Danger!
Make sure that the chain brake is released. Pull back the handle/chain brake before operating.
Noise emission complies with Directive 2000/14/EC!
Explanation of the symbols for the handling label on the machine.
A safety sign is fitted to the chain saw’s fan filter cover. This label, along with the safety instructions
on these pages, should be carefully read before attempting to operate this unit.
IMPORTANT! Picture 1/2/3 Warns about a dangerous method of working that must not be used.
Picture 4 Recommends operation for safe sawing.
1. Avoid contact with the tip of the rail (chain return point). RECOMMENDED.
2. Warning! Beware of recoil.
3. Do not hold the saw in one hand.
IMPORTANT! Hold the saw firmly with both hands. Place your right hand on the rear handle
and your left hand on the front handle.
Safety Information
8
Important - Please read these instructions fully before operating or maintaining
Customer Helpline 0151 649 1500
Explanation of the symbols for the brake function label on the machine.
Push the handle back to disengage the brake.
Push the handle forward to engage the brake, and stop the chain.
NOTE! The chainsaw is designed for occasional use by home owners, garden owners and campers
and is for general work such as stump grubbing, cutting firewood, etc. It is not designed for lengthy
use. If it is used for a lengthy period, the vibrations it causes in the hands of the user may result in
circulation problems (white finger syndrome).
Explanation of the Symbols and Warning signs on the machine continued
Inhaltsverzeichnis
Andere Qualcast Kettensäge Handbücher
