Quanser QNET Physics and Dynamics Bedienungsanleitung

Quick Start Guide: QNET Physics and Dynamics

Check Components and Details

STEP 1

Make sure your QNET Physics and Dynamics experiment includes the following components:

Additional Components Required

Install LabVIEW and Add-Ons

STEP 2

STEP 3

To complete your QNET Physics and Dynamics board setup, you will also need the following hardware:

Make sure the following versions of LabVIEW™ and required add-ons are installed:

1. LabVIEW™ 2012 or later

2. NI DAQmx 9.5.5 or later

3. NI ELVISmx 4.4 or later

4. LabVIEW™ Control Design and Simulation Module 2012 or later

1. Quanser QNET Physics and

Dynamics board, including:

a) Two pendulum rods

b) Coupling

c) Sliding mass

d) Free pulley

e) Two 100g and two 50g free weights

2. Table Tennis Ball

3. Anchor Screws

4. Hex key

5. Extension spring

6. Cable

Note: The QNET curriculum resources are

available for download at www.ni.com/qnets

121. NI ELVIS II or NI ELVIS II+workstation

2. +5VDC / 5A, +15VDC / 2A,

-15VDC / 0.8A Power Supply

3. USB Cable

Note: All references to NI ELVIS II in

this guide apply to both NI ELVIS II

and NI ELVIS II+ devices.

1a 1c 1d

GPower on the NI ELVIS II using the power switch on the back

of the unit. The READY and ACTIVE LEDs on the top NI ELVIS II

panel should briey light, and the READY LED stays on.

Slide the PCI

connector at

the back of

the QNET

board into

the female

connector on

the NI ELVIS II.

Place the handle

on the front of

the QNET board

over the bracket

located on the

front of the NI

ELVIS II.

Using the screws and hex key provided,

anchor the QNET board to the ELVIS II

in the locations indicated. Connect the NI ELVIS II

power supply to the back

panel of the NI ELVIS II.

Use the NI ELVIS II USB cable

to connect the NI ELVIS II

Unit to your computer.

E F

AEnsure that the NI ELVIS II power switch is in

the OFF position.

HEnsure that

the +5V LED

on the QNET

board is lit.

Power on the QNET Physics and

Dynamics board by turning the NI

ELVIS II prototyping board power

switch. The POWER LED next to

the switch should light up.

Setup Hardware

STEP 4

To setup the complete QNET Physics and Dynamics, please read the following instructions carefully. For full details, see

the QNET Physics and Dynamics User Manual.

Testing the QNET Physics and Dynamics

STEP 5

Click on the STOP

button to stop running

the VI.

Click on the

white arrow

to run the VI.

Make sure that the Pulley

Encoder graph is also

showing a change in angle

when the pulley is spun

back and forth.

1. Remove the sliding mass from its storage

location on the support bar, and place it

next to the electromagnetic as shown.

2. Press the Lock Mass button on the VI,

and check that the mass becomes rmly

attached to the magnet.

Press the catapult arm down until it latches

against the magnetic arm lock. Make sure

that it is rmly held in place. Press the FIRE

button and check that the Arm Speed graph

shows a change in the arm angle.

Select the device name to match your

NI ELVIS II device as shown in the NI

Measurement & Automation Explorer

in the Dev i ce control.

Make sure your PC,

NI ELVIS II, and QNET

board are powered ON.

Open the Quick Start folder from the Physics and Dynamics

folder in the QNET Resources. The QNET Resources are available

for download from www.ni.com/qnets.

COpen the LabVIEW Virtual Instrument (*.vi)

found under the Quick Start folder

Review the following recommendations before contacting Quanser’s technical support engineers

TROUBLESHOOTING

STILL NEED HELP? For further assistance from a Quanser engineer, contact us at tech@quanser.com

or call +1-905-940-3575.

The +5 LED on

the QNET Physics

and Dynamics

board is not lit.

• Ensure that the PCI connector on the QNET board is properly connected to the female

connector on the NI ELVIS II unit.

•Check that the system power switch, located on the back panel of the NI ELVIS II unit,

and the prototyping power switch, situated on the top of the NI ELVIS are ON.

•If the +5V LED is still not lit, then the +5V fuse on the Protection Board of the NI ELVIS II

has been triggered. See the Protection Board Fuses in the NI ELVIS II User Manual.

LEARN MORE For full range of QNETs visit www.ni.com/quanser.

For advanced control tools for teaching and research, visit www.quanser.com

Expand your lab using other QNETs for NI ELVIS

• QNET DC Motor

• QNET Rotary Pendulum

• QNET VTOL

• QNET HVAC board

• QNET Mechatronic Actuators board (NEW for 2015)

• QNET Mechatronic Sensors

• QNET Myoelectric

Andere Handbücher für QNET Physics and Dynamics

Andere Quanser Lehrmittel Handbücher

Quanser

Quanser QNET 2.0 HVAC Bedienungsanleitung

Quanser

Quanser 6 DOF Hexapod Bedienungsanleitung

Quanser

Quanser QNET 2.0 Bedienungsanleitung

Quanser

Quanser 3 DOF Bedienungsanleitung

Quanser

Quanser QNET Mechatronic Actuators Bedienungsanleitung

Quanser

Quanser QNET Physics and Dynamics Bedienungsanleitung

Beliebte Lehrmittel Handbücher anderer Marken

DISCOVER

DISCOVER talking pen Bedienungsanleitung

pitsco

pitsco Smart Buddies 45895 Bedienungsanleitung

RS 3.5 Bedienungsanleitung

CAE Healthcare

CAE Healthcare METIman Bedienungsanleitung

Turning Technologies

Turning Technologies Pulse Bedienungsanleitung

fischertechnik

fischertechnik STEM Coding Pro Bedienungsanleitung

Experia

Experia IRiS Light Wand Bedienungsanleitung

Pitsco Education

Pitsco Education FLO Bedienungsanleitung

Sphero

Sphero RVR RV01 Bedienungsanleitung

Limbs & Things

Limbs & Things 60905 Bedienungsanleitung

JP TURN Connect T101 Bedienungsanleitung

TruCorp

TruCorp AirSim Advance Bedienungsanleitung

LeapFrog

LeapFrog Mr. Pencil's Scribble, Write & Read Bedienungsanleitung

ScienTECH

ScienTECH 2261 Bedienungsanleitung

Rompa

Rompa 20019 Bedienungsanleitung

Duinotech

Duinotech XC4322 Bedienungsanleitung

Enabling Devices

Enabling Devices Spinning Light Show Bedienungsanleitung

Adam,Rouilly

Adam,Rouilly AR253 Bedienungsanleitung