Quantum Instruments Qflash 5d-R Series Bedienungsanleitung
Qflash®
“5d-R” series
Digital Flash
Models QFT5d-R, QFX5d-R
Operating Instructions
Quantum Instruments
Designed and manufactured in the USA
QFT5d-R-- powered by Qu ntum Turbo® b tteries
QFX5d-R-- powered by Qu ntum Qp q System
Q T5D P635A 1.11_Q T5D P635A 1/11/12 1:50 PM Page 1
MOpen lash (Test)
n Option Button
LDown Button Up Button J
Modeling Light l
Video Light when
reflector set to
RING
Set Button u
Mode Button I
lash
Indicator
Reflector Lock
Ring
Q T5D P635A 1.11_Q T5D P635A 1/11/12 1:50 PM Page 2
Q T5D P635A 1.11_Q T5D P635A 1/11/12 1:50 PM Page 3
Speaker
lash indicator LEDs
On solid - lash ready
Blinking - lash recycling
ront curtain sync
Rear curtain syns
Reflector no diffusers
Bare bulb reflector
Reflector with diffusing disks,
wide angle dome, or soft box
Telephoto reflector
Auto sensor limit turned off
Ring Light
Flash Display Symbols
Q T5D P635A 1.11_Q T5D P635A 1/11/12 1:51 PM Page 4
1
Section Description
1.0 Introduction
2.0 Warnings
3.0 Advanced eatures Summary
4.0 eatures available with QTTL
(D, Dw, Dw-R series) Adapters
5.0 Getting Started
6.0 Basic Navigation
7.0 Common eatures
8.0 Basic Options
9.0 Manual Mode Operation
10.0 Automatic Mode Operation
11.0 TTL and QTTL Mode Operation
12.0 Stroboscopic Mode Operation
13.0 Program Mode Operation
14.0 Wireless Qflash Operation
15.0 Wired Control Mode
16.0 Typical Lighting Situations
Qflash “5d-R” series flashes provide professional quality lighting for both
digital and film cameras. Quantum’s proprietary QTTL®Adapters dedicate
Qflash seamlessly to your camera. Many features of Qflash5d-R will
enhance your lighting control when used with non-dedicated/manual
cameras.
While powerful and extremely versatile, Qflash operation is intuitive and
straightforward. Advanced features for most lighting needs are accessible
as required.
We highly recommend reading this entire instruction manual.
Whether or not you require all of Qflash’s capability now, you will
want to know it exists when the need arises.
Series Qflash 5d-R adds wireless preflash TTL and wireless remote auto
to the Qflash features. These features apply when Qflash 5d-R is used in
combination with Dw-R series QTTL Adapters, reeXWire receivers
W7Q and W8R, and transmitter W9T or transceiver W10w. If you
own W10 transceivers, they can be upgraded to become W10w.
Qflash 5d-R models used with Quantum’s proprietary Dw-R Adapters
allow you to create ratios with multiple remote Qflashes in the wireless
TTL mode. Older D and Dw series Adapters can be upgraded to become
Dw-R adapters.
See www.qtm.com for costs for these upgrades. D, Dw, or Dw-R series
QTTL adapters are optional for specific makes and camera models.
Please consult your dealer or www.qtm.com for the latest availability.
.
1. INTRODUCTION
TABLE OF CONTENTS
Q T5D P635A 1.11_Q T5D P635A 1/11/12 1:51 PM Page 5
2
• Disconnect extern l power before ch nging the fl sh tube, or
connecting or disconnecting to/from c mer s, power p cks,
or ny other equipment.
• OPERATE ONLY WITH A FLASH TUBE IN THE SOCKET!!
• DO NOT TOUCH THE FLASH TUBE SOCKET WITH METAL
OBJECTS!!
• THIS IS A PROFESSIONAL INSTRUMENT. KEEP AWAY
FROM CHILDREN!!
• DO NOT ATTEMPT TO OPEN THE FLASH UNIT! DANGEROUS
HIGH VOLTAGE INSIDE!!
• Rep irs c n be m de only by qu lified Qu ntum service
represent tive.
2. WARNINGS AND CAUTIONS
The chart below summarizes the advanced features for various Qflash
series. A “U” means the Qflash model will have this feature when upgrad-
ed to series 5d-R. An “ ” means this feature is available in the model
shown.
Feature Qflash Models (T and X ty es)
QF4d QF5d QF5d-R
Wireless Control in Nikon/Canon
systems wit Qnexus UU F
Wireless multiple ratio TTL- wit
Dw-R Adapters & FreeXWire UU F
Wireless preflas TTL wit digital cameras
-using Dw/ Dw-R Adapters and FreeXWire UF F
Wireless remote Auto / Auto Fill mode UF F
Zone control of FW7Q from panel of Qflas UF F
Flas ready indication in camera viewfinder FF F
S utter speed control
(camera detects flas and sets s utter) FF F
Rear Curtain Sync FF F
Auto focus assist FF F
Auto Fill ratio FF F
3. ADVANCED FEATURES SU ARY
Q T5D P635A 1.11_Q T5D P635A 1/11/12 1:51 PM Page 6
3
4. FEATURES AVAILABLE WITH QTTL
(D, Dw, Dw-R SERIES) ADAPTERS
Quantum’s QTTL®adapters provide a dedicated link between Qflash 5d-R
series and popular digital and film cameras.
Wireless multiple r tio TTL - with Dw-R series Adapters & reeXWires,
remote Qflashes can be set to ratios of the camera’s TTL metering
system. or example, an on-camera flash could be set 1.6 stops down, a
main flash on the left to +1 stop, and a hairlight to –2 stops from the
camera TTL exposure.
Wireless preflash TTL with digital cameras - when using Dw or Dw-R
series QTTL Adapters, you can control Qflash exposure wirelessly with
your camera’s TTL exposure control system.
Rear curtain sync - If supported by your camera, the QTTL adapter can
fire Qflash in sync with the rear curtain. Rear curtain sync is selected by
a switch located on the back of the adapter.
Auto focus assist - If your camera requires an infrared focus assist, the
QTTL adapter will project a beam when the camera focuses.
Flash Sync speed control - If flash readiness is achieved, the camera’s
automatic system switches the shutter speed to the correct flash sync
speed.
Ready light - lash readiness is established when the “Ready” indicator
appears in the Qflash display. If “flash ready” is supported by the camera,
then a flash symbol will appear in the viewfinder when Qflash is recycled
and ready.
Pre-flash TTL - Cameras that have advanced TTL metering systems
require a pre-flash to determine proper exposure. This pre-flash is sup-
ported by the QTTL adapters.
QTTL adapters support the features mentioned above only when the
camera connected also supports those features. Please see the list of
adapters available for cameras in the latest Quantum Price List or at
www.qtm.com.
Q T5D P635A 1.11_Q T5D P635A 1/11/12 1:51 PM Page 7
4
5.2 Reflectors and Bare Bulb
Reflectors are secured by the locking
ring near the base of the reflector.
Rotate the ring in the directions
shown in the diagram to loosen or
tighten the reflectors.
When inserting a reflector, first slowly rotate
it until the notch in the reflector “drops” fully
into head of the Qflash. Then tighten the
locking ring. If you do not let the reflector drop
fully into the Qflash before locking it, the reflector
may become loose during use.
Note to previous Qflash T, T2 ,X or X2 owners: There is no longer a “Wide”
position for the reflectors. The only position is “Normal”. or wide angle
coverage, use the included flat diffusers, or
optional Q 67A wide angle or Soft Box
Q 68 diffusers.
5.3 Bounce and Swivel Head
The head position is locked and can
be changed with a single button (see
diagram). Press and hold this button, then
adjust the head to the desired position. Release
the button, and slightly move the head until it
“clicks” and locks the head into the vertical and
horizontal planes.
5. GETTING STARTED
5.1 Inserting the Flash Tube
Match the red dot on the base of the flash tube with the red dot in the sock-
et of Qflash. Push the flash tube in until it is seated snugly into the socket.
Excessive force is not required.
Replace the flash tube only with Quantum type Q 30 or Q 30uv for Qflash
model T5d / T5d-R. Qflash model X5d / X5d-R requires Q 32 or Q 32uv
flash tubes. Other flash tubes will not provide proper exposure, may not
work at all, or they may damage the Qflash.
A rox. Guide No. for ISO 200*
Reflector Angle QFT5d-R QFX5d-R
200Ws 400Ws
Normal QF60 55˚ 226ft / 72m 226ft / 72m 320ft / 100m
QF60 w/flat diffuser 90˚ 128ft / 40m 128ft / 40m 180ft / 56m
QF67A Dome Diffuser
QF68 Soft Box 120˚ 90ft / 28m 90ft / 28m 128ft / 40m
QF69 Mini Soft Box
QF62Bs/g Bare Bulb Reflector
180˚ 60ft / 19m 60ft / 19m 90ft / 28m
Q T5D P635A 1.11_Q T5D P635A 1/11/12 1:51 PM Page 8
5
5.4 Bracket ounting
Qflash mounts with a 1/4-20 standard tripod thread to brack-
ets, light stands, and tripods. Many brackets are made
especially for Qflash by popular bracket manufacturers.
Quantum has two optional brackets, models
Q 70US and Q 70E. The instructions below
describe mounting to both of these brackets
and to other manufacturers brackets, light
stands, and tripods.
Two types of 1/4-20 fasteners screw/knob and
a friction pad are supplied with Qflash. Place
the friction pad between Qflash and the bracket,
insert the knob/screw and tighten. (If the mounting
surface has a pad, the friction pad is not necessary).
Note: Brackets vary in thickness - always make sure that
the mounting knob/screw screws into Qflash at least two complete turns.
5.5 Connecting Qflash to a Camera
There are two ways to connect a Qflash to a camera- wired and wireless.
or wired connection use either of these methods:
• Connect a household two-prong sync cord (supplied) to the sync
connector of Qflash.
• Connect a Q series TTL adapter to the camera hot shoe.
• Connect a D, Dw, or Dw-R series QTTL adapter to the camera hot shoe.
• Connect a Q 53 Hot Shoe sync to the camera.
or wireless connection
• Use the reeXWire system. See Section 14 - Wireless Qflash Operation
Consult your dealer or www.qtm.com for the latest TTL and QTTL
adapter models.
Note: When using a household type (two-prong) sync cord, if you have
difficulty getting the flash to fire, Remove the two-prong plug from the
Qflash and reinsert it in the opposite direction. This changes the polarity
of the Qflash to match the polarity of the camera.
5.6 Powering Qflash
Before turning on any power to Qflash always make all electrical
connections first, both to the camera and to the power pack. Qflash
“T” models are powered by any Quantum Turbo Battery including Turbo
2x2, Turbo Compact, Turbo Z, and Turbo SC. Quantum “X” models are
powered by the Quantum Qpaq system.
Plug the Qflash power cable into the output connection of the appropriate
power pack. Turn on Turbo or Qpaq power. Normally Qflash will be pow-
ered up and ready to run.
If a “Check Turbo” or “Check Power” message appears on the Qflash
display, turn off the Turbo or Qpaq, wait one second, and turn it on again.
If the message appears again, the power pack needs recharging. If a
“Reset lash?” message appears in the Qflash display press any button,
except the ode Ibutton, to resume operation.
Q T5D P635A 1.11_Q T5D P635A 1/11/12 1:51 PM Page 9
6
6. BASIC NAVIGATION
This Section explains how to maneuver your way around the
Qflash 5d-R
Very Important Tips
For consistent exposures with your digital camera and Qflash.
• Always do a custom white balance before shooting
• When shooting TTL use Aperture or Shutter priority or anual
camera modes
• Set your metering area to center weight, partial metering
instead of matrix or multi-spot metering.
• Your Qflash provides 150 watt-seconds of power compared to
50 watt-seconds of a typical shoe mount flash. When shooting
6 ft. (2m) or closer, at ISO 200 or greater, with a wide open F/#,
you must always diffuse the light. Otherwise your subject will
be over-exposed.
Q T5D P635A 1.11_Q T5D P635A 1/11/12 1:51 PM Page 10
Dieses Handbuch passt für folgende Modelle
4
Inhaltsverzeichnis
Andere Quantum Instruments Kamerablitz Handbücher
