Quantum StorNext QD7000 Bedienungsanleitung
Replacing a Drawer in Base System/
Expansion Unit
StorNext QD7000
Firmware 8.30.xx.xx
6-68569-01 Rev A
ii Replacing a Drawer in Base System/Expansion Unit
Replacing a Drawer in Base System/Expansion Unit, 6-68569-01 Rev A, April 2017 Product of USA.
Quantum Corporation provides this publication “as is” without warranty of any kind, either express or implied, including but not
limited to the implied warranties of merchantability or fitness for a particular purpose. Quantum Corporation may revise this
publication from time to time without notice.
COPYRIGHT STATEMENT
© 2017 Quantum Corporation. All rights reserved.
Your right to copy this manual is limited by copyright law. Making copies or adaptations without prior written authorization of
Quantum Corporation is prohibited by law and constitutes a punishable violation of the law.
TRADEMARK STATEMENT
Artico, Be Certain (and the Q brackets design), DLT, DXi, DXi Accent, DXi V1000, DXi V2000, DXi V4000, DXiV-Series, FlexTier,
Lattus, the Q logo, the Q Quantum logo, Q-Cloud, Quantum (and the Q brackets design), the Quantum logo, Quantum Be Certain
(and the Q brackets design), Quantum Vision, Scalar, StorageCare, StorNext, SuperLoader, Symform, the Symform logo (and
design), vmPRO, and Xcellis are either registered trademarks or trademarks of Quantum Corporation and its affiliates in the United
States and/or other countries. All other trademarks are the property of their respective owners. Products mentioned herein are for
identification purposes only and may be registered trademarks or trademarks of their respective companies. All other brand names
or trademarks are the property of their respective owners. Quantum specifications are subject to change.
Replacing a Drawer in Base System/Expansion Unit iii
Preface
Note: The 8.30.xx.xx firmware (Lehigh) is used in the QD7000 (E5600,
Titan RAID controller, only). Refer to the NetApp to Quantum
Naming Decoder section for additional information.
This section provides the following information:
•Audience
•Prerequisites
•NetApp to Quantum Naming Decoder
•Product Safety Statements
•Contacts
•Comments
•Quantum Global Services
Audience This manual is intended for storage customers and technicians.
Preface
iv Replacing a Drawer in Base System/Expansion Unit
Prerequisites Prerequisites for installing and using this product include knowledge of:
• Servers and computer networks
• Network administration
• Storage system installation and configuration
• Storage area network (SAN) management and direct attach storage
(DAS)
• Fibre Channel (FC) and Ethernet protocols
NetApp to Quantum
Naming Decoder
Use Table 1 to correlate the NetApp product nomenclature to the
equivalent Quantum-storage naming conventions.
Table 1 Product Nomenclature
E-Series NetApp
Product Quantum-Storage Description
Controller-Drive Tray Base System Quantum uses Base System when referring to a drive
tray with the RAID controllers.
Drive Tray Expansion Unit Quantum uses Expansion Unit when referring to a
drive tray with the environmental services modules
(ESMs).
E5600 (Code Name:
Titan)
RAID Controller Four 16Gb/s FC SFP+ host ports
E5500 (Code Name:
Soyuz)
RAID Controller Four 16Gb/s FC SFP+ host ports
E5400 (Code Name:
Pikes Peak)
RAID Controller Four 8Gb/s FC SFP+ host ports
DE6600 (Code Name:
Wembley)
4U 60-drive
enclosure
Sixty 3.5 inch disk drives
Preface
Replacing a Drawer in Base System/Expansion Unit v
E5560 or E5660
(DE6600 4U drive
enclosure with
E5500 or E5600 RAID
controllers)
Quantum StorNext
QD7000
E5460
(DE6600 4U drive
enclosure with
E5400 RAID
controllers)
Quantum StorNext
QD6000
E5424
(DE5600 24-drive 2U
drive enclosure
(Code Name:
Camden with E5400
RAID controllers)
Quantum StorNext
QS2400
E5412
(DE1600 12-drive 2U
drive enclosure
(Code Name: Ebbets
with E5400 RAID
controllers)
Quantum StorNext
QS1200
E-Series NetApp
Product Quantum-Storage Description
Preface
vi Replacing a Drawer in Base System/Expansion Unit
Product Safety
Statements
Quantum will not be held liable for damage arising from unauthorized
use of the product. The user assumes all risk in this aspect.
This unit is engineered and manufactured to meet all safety and
regulatory requirements. Be aware that improper use may result in
bodily injury, damage to the equipment, or interference with other
equipment.
WARNING: Before operating this product, read all instructions and
warnings in this document and in the system, safety, and
regulatory guide.
Preface
Replacing a Drawer in Base System/Expansion Unit vii
Contacts For information about contacting Quantum, including Quantum office
locations, go to:
http://www.quantum.com/aboutus/contactus/index.aspx
Comments To provide comments or feedback about this document, or about other
Quantum technical publications, send e-mail to:
Preface
viii Replacing a Drawer in Base System/Expansion Unit
Quantum Global
Services
Accelerate service issue resolution with these exclusive Quantum
StorageCare services:
•Service and Support Website - Register products, license software,
browse Quantum Learning courses, check backup software and
operating system support, and locate manuals, FAQs, firmware
downloads, product updates and more in one convenient location.
Benefit today at:
http://www.quantum.com/serviceandsupport/get-help/
index.aspx#contact-support
•eSupport - Submit online service requests, update contact
information, add attachments, and receive status updates via email.
Online Service accounts are free from Quantum. That account can
also be used to access Quantum’s Knowledge Base, a
comprehensive repository of product support information. Get
started at:
http://www.quantum.com/customercenter/
For further assistance, or if training is desired, contact the Quantum
Customer Support Center:
North America 1-800-284-5101 (toll free)
+1-720-249-5700
EMEA +800-7826-8888 (toll free)
+49-6131-324-185
APAC +800-7826-8887 (toll free)
+603-7953-3010
For worldwide support:
http://www.quantum.com/serviceandsupport/get-help/
index.aspx#contact-support
E-Series
Replacing a Drive Drawer in a 60-Drive Tray
The steps to replace a failed drive drawer in an E-Series 60-drive tray depend on whether the volumes in the drawer are
protected by Drawer Loss Protection. If all volumes in the drive drawer are in volume groups or disk pools that have Drawer
Loss Protection, you can perform this procedure online. Otherwise, you must stop all host I/O activity and power off the tray
before replacing the drive drawer.
This procedure applies to the following controller-drive trays and expansion drive trays:
• E2660 controller-drive tray
• E2760 controller-drive tray
• E5460 controller-drive tray
• E5560 controller-drive tray
• E5660 controller-drive tray
• DE6600 drive tray
Each of these 60-drive trays has five drive drawers.
And each of the five drawers can hold up to 12 drives.
1
215-10780_A0 December 2015 Copyright ©2015 NetApp, Inc. All rights reserved.
Before you begin
You need these items for this procedure:
• Antistatic protection
Attention: Possible hardware damage – To prevent electrostatic discharge damage to the drive tray, use proper antistatic
protection when handling drive tray components.
• Replacement drive drawer
• Replacement left and right cable chains
• Orange cable chain removal tool
Note: The cable chain removal tool makes it easier to reach into the enclosure and easier to unplug the cable chain
connectors. If you do not have the tool, you can use your fingers to unplug the connectors.
• Flashlight
• Permanent marker
Steps
1. Preparing to remove a drive drawer on page 2
2. Removing the cable chains on page 4
3. Removing a drive drawer on page 9
4. Installing a drive drawer on page 11
5. Attaching the cable chains on page 13
Preparing to remove a drive drawer
If the drive tray is powered on, you must issue the Set Drawer Service Action Allowed Indicator CLI command to
prevent the controller from accessing the drive drawer. This command also allows you to determine if the drives in the drawer
are in volume groups or disk pools protected by Drawer Loss Protection.
Before you begin
Before issuing the CLI command, confirm that the drive tray meets all of these conditions:
• The drive tray cannot be over temperature.
• Both fans must be installed and have a status of Optimal.
• All drive tray components must be in place.
• The volumes in the drive drawer cannot be in a Degraded state.
Attention: Possible loss of data access – If a volume is already in a Degraded state, and you remove drives from the drive
drawer, the volume can fail.
2Replacing a Drive Drawer in a 60-Drive Tray
Andere Handbücher für StorNext QD7000
13
Inhaltsverzeichnis
Andere Quantum Disk-Array-System Handbücher
Beliebte Disk-Array-System Handbücher anderer Marken
Fujitsu
Fujitsu ETERNUS DX60 S2 Bedienungsanleitung
Accom
Accom WSD/2XTREME Bedienungsanleitung
HP
HP Compaq Presario,Presario 4400 Gebrauchsanweisung
ATTO Technology
ATTO Technology Diamond Storage Array V-Class Bedienungsanleitung
National Instruments
National Instruments RMX-8268 Bedienungsanleitung
Overland Tandberg
Overland Tandberg SnapServer DX1 Bedienungsanleitung
