Quark-Elec QK-G031 Bedienungsanleitung

Quark-elec Manual

https://www.quark-elec.com 1of 28 2018

QK-G031 Temperature GSM Remote Controller

Manual

Features

Runs of 12.0V mains or Liquid cell battery

Remote temperature monitoring and control by mobile phone GSM SMS message

2 alarm inputs and 3 Relay outputs

Automatic notification by SMS message when alarm input is triggered

Remote control of 3 Relay outputs by SMS message

Automated control of 2 Relay outputs activated by alarm inputs

Automated control of 3 Relay outputs activated by temperature sensors and temperature ranges.

Scheduled control of 3 Relay outputs by SMS message

In-built clock for programming scheduled switch state

Status request and response by SMS

Remote manual override

Android APP interface

Up to 4 mobile phones can monitor and control each unit

Easy to install and configure via SMS or Android APP (no PC required)

Compatible with all major 2G SIM networks

Mains power/battery drop off notification

Mains power recovery notification when within 60 seconds or when using backup battery power.

12.0V liquid battery options for main power source and/or back-up power with battery charging.

Quark-elec Manual

https://www.quark-elec.com 2of 28 2018

Contents

1. Setup overview.................................................................................................................................................... 3

2. Introduction.......................................................................................................................................................... 4

3. Enclosure..............................................................................................................................................................5

4. Power connections..............................................................................................................................................6

4.1. 12.0V DC power connection................................................................................................................ 6

4.2. Battery connections...............................................................................................................................6

5. Status LED’S........................................................................................................................................................7

6. Preparing SIM card.............................................................................................................................................8

6.1. Insert SIM into the SIM card slot.........................................................................................................8

6.2. Registration of Main SIM Controller................................................................................................... 8

6.3. Registering additional SIM controllers............................................................................................... 9

7. Resetting.............................................................................................................................................................. 9

7.1. Factory reset G031 memory................................................................................................................9

7.2. Reset main controller SIM number..................................................................................................... 9

8. Alarm function connections............................................................................................................................. 10

9. Relays.................................................................................................................................................................11

9.1. Relay wiring..........................................................................................................................................11

9.2. Daily timer setting................................................................................................................................11

9.3. Relay working mode (relay 1 and 2)................................................................................................ 12

9.4. Latching mode settings...................................................................................................................... 13

10. Temperature monitoring & control.............................................................................................................14

10.1. Setting Temperature Ranges........................................................................................................14

10.2. Relay wiring and temperature settings example........................................................................15

11. App on Android.............................................................................................................................................16

11.1. Setup Main Controller SIM Number.............................................................................................17

11.2. Register SIM cards......................................................................................................................... 18

11.3. Setting the clock on the QK controller......................................................................................... 18

11.4. Check relay working mode............................................................................................................ 19

11.5. Rename control terminals..............................................................................................................19

11.6. Control panel................................................................................................................................... 20

11.7. Alarm log.......................................................................................................................................... 21

11.8. Other................................................................................................................................................. 21

12. Command and response SMS list.............................................................................................................23

13. Specification..................................................................................................................................................27

14. Limited Warranty and Notices....................................................................................................................28

Quark-elec Manual

https://www.quark-elec.com 3of 28 2018

1. Setup overview

You will need:

SIM card:

SIM must operate on the GSM (2G) network for this version. Check with your SIM supplier.

Credit on the SIM (we recommend automatic top-ups)

The SIM is not PIN protected

The SIM is set to disable voicemail

Avoid SIM cards that deactivate automatically if the SIM is not used often. If your G031 is likely to

be unused for long periods of time, you will have to send the G031 an update request periodically to keep

the SIM card active. The time limit is often three months.

2. Power supply cable: long enough to reach your device in its final location.

3. Check there is mobile network reception for your SIM card in the location that your device will be

installed (you can check the SIM card in a mobile phone).

4. Temperature sensors (included) which come in 1, 2 and 6 metre lengths and can be shortened or

extended (we recommend a maximum of 8 metres).

5. Optional liquid cell 12.0V battery: Can be plugged into G031 for backup power.

Installation

1. Download and install the APP https://www.quark-elec.com/downloads/APPs/

2. Select G031 location: location must be indoors and not exposed to water or high humidity.

3. Connect the relays outputs (if required): check relay setup for whether you want relays in normal

open (NO) or normal closed (NC) position. See back page.

4. Connect alarm inputs (if required) to the correct terminal: alarm inputs (INT) 1/2 will activate relay 1/2

respectively. The G031 is compatible with inputs that send signals as a switch (by closing the circuit) and

alarm inputs that send a low voltage signal.

5. Connect temperature sensors by inserting the connector block into the slots at the back of the G031.

Good practice is to label each sensor and its corresponding relay. This will help later on.

6. Insert your SIM into the G031 device (make a note of the SIM number first for reference).

7. Connect to power: Check LEDs are working correctly.

Blue Network LED: LED will flash blue at start up as it is connecting to a network. Once

connected, the LED will flash once every 2 to 3 seconds.

Red System LED: will flash at 1 second intervals once the system has finished initialization. The LED

will not flash while the G031 is processing a command.

8. Hold down reset button for 10 seconds.

9. Register the main phone number that will control the device within 10 minutes of powering up

the G031 by texting ‘88888888’ from your chosen phone to G031 SIM card. If registration is successful,

the module will reply with ‘Your phone has been registered’. If unsuccessful, the module will reply with

‘registered disabled’. If registration is unsuccessful, Hold down reset button for 10 seconds and

reattempt registration within 10 minutes. The system LED will flash at one second intervals once the

registration is completed. You can add up to three additional control mobile phones (check the manual for

full list of text command codes).

You can send commands and receive updates by SMS text or the text generating android APP.

Remember; the device processes one command at a time. Each command will have a reply to

confirm the command has been received and executed. You must wait for a reply message before

sending another command.

(This is an overview only. Familiarize yourself with the manual before installation.)

Quark-elec Manual

https://www.quark-elec.com 4of 28 2018

2. Introduction

The G031 series remote controller is a versatile device which can be attached to many electronic devices

in homes, offices, plant or wherever required. It includes three independent relay switches and two digital

alarm inputs. It allows operators to control/monitor remote temperatures or equipment using SMS (Short

Message Service) via the GSM network. It also allows for automated temperature or alarm activated

action. Up to 4 mobile phone numbers (SIM card numbers) can be registered with the remote controller.

These mobile phones can belong to technicians, engineers or individuals who have a requirement to

control and/or monitor corresponding devices.

The G031 features:

Three relay output connections: for connection to the equipment that is to be controlled

oRelay 1: Manual SMS control, Automated control, Daily timer

oRelay 2: Manual SMS control, Automated control, Daily timer

oRelay 3: Manual SMS control

Three thermistor temperature sensors: with three linked relay outputs.

Two digital alarm inputs connections: for connection to various inputs to be monitored (an alarm

SMS can be received when either alarm input is triggered. The alarm input can also be set to trigger

automated control of the machinery connected to the Relay outputs 1 and/or 2).

Four control mobile phones: one main control terminal and up to 3 additional control terminals can

be registered with G031.

Android APP: the device can be controlled by either SMS text message codes or the text

generating APP for Android phones. This is a touch sensitive, user friendly interface.

Optional battery input: to allow the device to keep running during a power break. it has the Added

benefit of battery charging once the power is restored.

Quark-elec Manual

https://www.quark-elec.com 5of 28 2018

3. Enclosure

The enclosure is made of IP56 Insulation Class 2 plastic. External dimension: 145 x 90 x 41 mm.

Quark-elec Manual

https://www.quark-elec.com 6of 28 2018

4. Power connections

4.1.12.0V DC power connection

The G031 module can be supplied by 12.0-24.0V DC power. Connect a 12.0V DC power supply to the

power input screw terminals and switch on the power supply. The red system LED will flash at 1 second

intervals once the system has finished initialization. The blue network LED indicator will initially flash

quickly and, once logged onto the network, it will flash more slowly, approximately once every 3 seconds

4.2.Battery connections

The G031 supports backup battery inputs. The battery can be an auxiliary power supply for operation

during mains power failure. A 12.0V rechargeable Li-ion or Lead-acid battery can be connected to battery

input terminals on the G031.

Connection to a battery can allow the G031 to operate for up to a few days (depending on the battery

capacity) without mains power. The G031 will alert the operator when mains power has been lost and

recovered. The battery will recharge when power is restored. When recharging the battery, the mains

power input should be at least 2.0V higher than the battery’s full voltage level. Therefore, the mains

power supply voltage should be 14.0-24.0V.

Quark-elec Manual

https://www.quark-elec.com 7of 28 2018

5. Status LED’S

The device has two working LED’s to notify the user of its operations.

Blue Network LED – Blue LED will flash at start up as it looks for a network signal. Once a signal has

been found the LED will flash much slower, every 3 seconds.

Red System led – Red led will flash at 1 second intervals once the system has finished initialization.

It will not flash while it is processing a command.

Remember, the device processes one command at a time. Each command will have a reply to

confirm the command has been received and executed. You must wait for a reply message before

sending another command. All SMS text commands must always be sent using CAPITAL

letters. Do not add spaces or any other characters.

Quark-elec Manual

https://www.quark-elec.com 8of 28 2018

6. Preparing SIM card

Please ensure:

The SIM must operate on the GSM (2G) network. Most network providers provide 2G cover, check

with your supplier.

There is credit on the SIM (we recommend automatic top-ups)

The SIM is not PIN protected

The SIM is set to disable voicemail

Avoid SIM cards that deactivate automatically if the SIM is not used often (usually after3 months

inactivity). If you’re SIM will do this and if you’re G031 is likely to be unused for long periods of time;

send the G031 an update request periodically to keep the SIM card active.

texts to be sent from G031 module.

The PIN request option should be disabled from the SIM card before inserting it into the G031 module. To

check the PIN request status of your SIM card, place the card in an unlocked mobile phone and switch

the phone on. If normal calls can be made without entering a PIN number, then it is disabled. Please also

make sure voicemail is disabled before inserting the SIM card into the module.

If a ‘pay as you go’ (PAYG) SIM card is used, it is recommended that users choose to automatically ‘Top-

Up’ when the credit falls below a certain limit. Some PAYG SIM cards will be de-activated by the network

if they are not used to make an outgoing voice call or send an SMS text message within a specific period.

To prevent this, simply send the G031 a text for example ‘DQSJ’ (this can be done through the APP) and

G031 will reply with the local time by text message. This should be done periodically to keep the SIM

card active if required by your SIM provider.

6.1.Insert SIM into the SIM card slot

1. Write down SIM number before inserting into the G031

2. The SIM card should be inserted into the SIM card slot before applying the power.

3. Power Up (See next chapter)

6.2.Registration of Main SIM Controller

Users can setup the authorized telephone numbers within G031. The controller will verify the incoming

number if they are indexed in the registered SIM numbers, then the G031 controller will hang up and then

execute the actions.

The following steps are required to configure G031 for first time use:

Insert the SIM card into controller box

Power up and hold reset button for 10 seconds

Within ten minutes of resetting Text ‘88888888’ by SMS to the G031 controller. If successful, the user

will receive the message ‘Your phone has been registered’. This command should be received

within the first 10 minutes after powering up G031, otherwise the message ‘registered Disabled’ will

be received. If this happens reset.

Quark-elec Manual

https://www.quark-elec.com 9of 28 2018

6.3.Registering additional SIM controllers

You can add up to three additional control mobile phones. When adding additional numbers to the unit

you must enter them in the correct format used by the Network service provider of the SIM that you have

entered into the G022. For example, if the UK number 07123456789 needs adding; then we have three

formats to try (Using the UK country code '44').

1. +447123456789

2. 00447123456789

3. 07123456789

The most commonly used, is format 1, this will work with most providers. To store your number, text

‘BD1+447123456789F’ to the device. If you are able to send commands from the new number but do

not receive messages back, try one of the other formats.

You can now control the device by either:

Manually entering the codes by SMS text message

Using the phones Android APP interface. Using the APP, simply select the action you want and the

APP formulates and sends the SMS message for you.

App sent messages will be charged at your normal text rate.

7. Resetting

The G031 has two types of reset. You can:

Factory reset the module itself.

Reset the main SIM controller SIM number (main mobile number in control of module), whilst

keeping other settings.

7.1. Factory reset G031 memory

1. Hold the reset button for 10 seconds – the red LED should stay constantly on.

2. You now have 600 seconds to send the message ‘88888888’ to the SIM card in the G031

3. This will register you as the main SIM controller.

You can also reset the Main controller SIM remotely, For example when the main SIM controller number

has changed or you need to reset permissions for the main controller. This code allows you to remotely

remove and reset all mobile phone numbers stored in the device.

7.2. Reset main controller SIM number

1. Send ‘XGZHM’ command via text to the G031 SIM.

2. send ‘88888888’ within 600 seconds to the G031

3. The module will reply with ‘Your phone has been registered’.

If the G031 replies with the message ‘registered disabled’ or ‘Registered not allowed. Please Factory

reset G031 module first’ then repeat factory reset steps.

Quark-elec Manual

https://www.quark-elec.com 10 of 28 2018

8. Alarm function connections

G031 has two external alarm input connectors and various inputs can be connected to them. For

example, door/windows sensors, smoke alarms, carbon dioxide detectors, motion sensors, thermostats,

temperature/wind detectors, and moisture detectors.

Using these sensors/detectors, G031 can be setup as a protection/alarm and response system.

Alarm input port

Corresponding relay number

External alarm 1 (INT1)

Relay 1

External alarm 2 (INT2)

Relay 2

There are two typical ways the external alarm inputs can communicate with G031. External alarm devices

can be used as,

1. Switch

2. Alarm input source (low level voltage signal)

G031 external alarm inputs are active when a trigger pulse or a constant level of 0.0V is applied.

If the sensor/detectors are triggered (low level signal (0.0V) to G031); G031 will send out an SMS to the

registered mobile terminals. Meanwhile, the corresponding relays setup will be activated.

To disable the external alarm input, text 'EXTGBn' (replace ‘n’ with the relay number).

To enable all external alarm inputs, text 'EXTRT'.

Andere Handbücher für QK-G031

Inhaltsverzeichnis

Andere Quark-Elec Temperaturregler Handbücher

Quark-Elec

Quark-Elec QK-W016 Bedienungsanleitung

Beliebte Temperaturregler Handbücher anderer Marken

Swegon

Swegon LUNAd MB Bedienungsanleitung

Lucky Reptile

Lucky Reptile Thermo Control II Bedienungsanleitung

SENSORMETRIX

SENSORMETRIX Argon 100 Bedienungsanleitung

Fuji Electric

Fuji Electric PXE4 Bedienungsanleitung

Yuyao gongyi

Yuyao gongyi XMT-808 series Bedienungsanleitung

Selec

Selec TC544C Bedienungsanleitung

P.W. KEY

P.W. KEY rt-208gt Bedienungsanleitung

Future Design

Future Design FDC-9200 Bedienungsanleitung

BH Thermal

BH Thermal BriskONE Bedienungsanleitung

Omron

Omron E5EX-H Bedienungsanleitung

West Control Solutions

West Control Solutions KS 45 Kurzanleitung

MCS

MCS RITC-15B Bedienungsanleitung

SMC Networks

SMC Networks Thermo-con INR-244-639 Bedienungsanleitung

eltherm

eltherm Ex-TC It Series Bedienungsanleitung

Omron

Omron C200H-TV Series Bedienungsanleitung

industrie technik

industrie technik CA1 Bedienungsanleitung

KRAL

KRAL EET 32 Bedienungsanleitung

dixell

dixell XR420C Verdrahtungsschema