Racelogic VBOX II Bedienungsanleitung

01 - VBOX II Front Panel

VBOX II units can be configured using the front panel buttons, which enables configuration without the need for a

computer. Configuration can also be made via the VBOX etup oftware.

From the main screen, press the’■’ button to enter the configuration screen.

Note: Entering the configuration screen will cause the VBOX to stop logging to the D card. When in

continuous logging mode, please ensure that the ’■' button is pushed prior to removing the D card to avoid

data loss.

Once in the configuration screen, press the ‘◄’and ‘►’ buttons to highlight the next or previous choice in any menu, and

press ’■’ to select the highlighted option. ost ain menus contain sub-menus, for example the Settings and Setup

Antennas menus contain separate menus for each parameter.

Note: The options highlighted in blue are only available on the SL series units.

https://racelogic.support//01VBOX_data_loggers/VBOX_II_Range/VBOX_II_User_Guide/01_-_VBOX_II_Front_Panel

ain enu

ETTING Press ’■’ to enter the VBOX general settings menu.

COLD TART Press ’■’ to perform a GPS cold start

MODE

Press ’■’ to change the mode of operation between

VBOX module mode and Stand Alone mode. Then

press ’■’ to confirm.

ETUP ANTENNA

Press ’■’ to enter the antenna configurations menu. This

menu contains separate sub-menus for pitch antenna

and roll antenna pairs

MOOTHING

Press ’■’ to edit the smoothing levels of the Lat acc and

Long acc channels, and also Slip, Pitch, Roll, channels

on SL units only.

OUTPUT Press ’■’ ’ configure the digital and analogue outputs.

EXIT Press ’■’ to exit the setup menu and cause the settings

to be saved in EEPRO

https://racelogic.support//01VBOX_data_loggers/VBOX_II_Range/VBOX_II_User_Guide/01_-_VBOX_II_Front_Panel

Settings enu

UNIT Press ’■’ to change the displayed Velocity units. Then

press ’■’ to confirm.

K H, PH or Knots

APPLICATION

Press ’■’ and then use the ‘◄’ and ‘►’ buttons to select

between AUTO OTIVE or ARINE mode. arine

mode causes the box to display the Pitch, Roll and Slip

angles as Trim, Heel and Leeway Angles on the built in

screen and also as channel names inside the logged

file.

U B MODE

Press ’■’ and then use the ‘◄’ and ‘►’ buttons to select

whether the USB port is assigned to Serial data mode or

Card reader mode.

CAN MODE

Press ’■’ and then the ‘◄’ and ‘►’ buttons to choose

between the following modes:

VCI MODE*

To connect any external CAN modules to the input of

the VBOX II

RACELOGIC MODULE MODE

To connect Racelogic CAN modules to the RLVBOX II

(input or output)

LOG OPTION Press ’■’ to enter the Log Options enu.

In this menu the Logging ode and Log rate can be set.

ERIAL RATE

Press ’■’ and then use the ‘◄’ and ‘►’ buttons to select

a serial data rate. The maximum serial rate is equal to

the Log rate.

Press ’■’ to enter the GPS configuration enu. The

Kalman Filter, Dynamic ode and DGPS mode is

configured within this menu.

TIME OFF ET Press’ the ‘◄’ and ‘►’ buttons to set an Time offset in

order to align the VBOX time to the users Local time.

https://racelogic.support//01VBOX_data_loggers/VBOX_II_Range/VBOX_II_User_Guide/01_-_VBOX_II_Front_Panel

BACK Press ’■’ to go back to the ain menu.

https://racelogic.support//01VBOX_data_loggers/VBOX_II_Range/VBOX_II_User_Guide/01_-_VBOX_II_Front_Panel

Setup Antennas (Pitch Antenna)

EPARATION

Press ’■’ and then use the ‘◄’ and ‘►’ buttons to

change the antenna separation. Then press ’■’ to

confirm.

Range is 0.5 – 5.0 m in 0.1 m increments

LEVEL

Press’■’ and then use the ‘◄’ and ‘►’ buttons to enable

or disable the LEVEL option. With the LEVEL set to YES

the RTK lock is more resilient.

But maximum ROLL or PITCH in this mode should be

10 degrees.

WAP ANTENNA Set to ‘ON’ to allow the primary Antenna A to be

mounted ahead of the Secondary Antenna B.

Default is ‘OFF’. Then press ’■’ to confirm.

LIP OFF ET

Press ’■’ to enter the Slip offset sub menu. Within this

sub menu the Slip offset can be calculated and applied

or cleared.

PITCH OFF ET

Press ’■’ to enter the Pitch offset sub menu. Within this

sub menu a Pitch offset can be calculated and applied

or cleared.

BACK Press ’■’ to go back to the ain menu.

https://racelogic.support//01VBOX_data_loggers/VBOX_II_Range/VBOX_II_User_Guide/01_-_VBOX_II_Front_Panel

Setup Antennas (Roll Antenna)*

*VB20 L3 triple antenna units only

EPARATION Press’■’ and then use the ‘◄’ and ‘►’ buttons to change

the antenna separation. Then press ’■’ to confirm.

Range is 0.5 – 5.0 m in 0.1 m increments

LEVEL

Press ’■’ and then use the ‘◄’ and ‘►’ buttons to enable

or disable the LEVEL option. With the LEVEL set to YES

the RTK lock is more resilient.

But maximum ROLL or PITCH in this mode should be

10 degrees.

ROLL OFF ET

Press ’■’ to enter the Roll offset sub menu. Within this

sub menu a Roll offset can be calculated and applied or

cleared.

BACK Press ’■’ to go back to the ain menu.

https://racelogic.support//01VBOX_data_loggers/VBOX_II_Range/VBOX_II_User_Guide/01_-_VBOX_II_Front_Panel

Smoothing enu

LAT ACC

Press ’■’ and then use the ‘◄’ and ‘►’ buttons to

change the amount of smoothing applied to the

calculated Lateral Acceleration output. Then press ’■’ to

confirm.

0.0 – 5.0 (0.1 steps)

LONG ACC

Press ’■’ and then use the ‘◄’ and ‘►’ buttons to

change the amount of smoothing applied to the

calculated Longitudinal Acceleration output. Then press

’■’ to confirm.

0.0 – 5.0 (0.1 steps)

LIP

Press ’■’ and then use the ‘◄’ and ‘►’ buttons to

change the amount of smoothing applied to the Slip

angle channel. Then press ’■’ to confirm.

0.0 – 5.0 (0.1 steps)

PITCH

Press ’■’ and then use the ‘◄’ and ‘►’ buttons to

change the amount of smoothing applied to the Pitch

angle channel. Then press ’■’ to confirm.

0.0 – 5.0 (0.1 steps)

ROLL

Press ’■’ and then use the ‘◄’ and ‘►’ buttons to

change the amount of smoothing applied to the Roll

angle channel. Then press ’■’ to confirm.

0.0 – 5.0 (0.1 steps)

BACK Press ’■’ to go back to the ain menu.

https://racelogic.support//01VBOX_data_loggers/VBOX_II_Range/VBOX_II_User_Guide/01_-_VBOX_II_Front_Panel

Outputs: Digital Setup enu (Channel 1 and 2)

OUTPUT

Press ’■’ and then use the ‘◄’ and ‘►’ buttons to

associate either of the following channels SPEED, SLIP,

PITCH, ROLL, LAT ACC and LONG ACC to the Digital

output. Then press ’■’ to confirm.

PUL E PER METER

Only available when output is set to SPEED.

Press ’■’ and then use the ‘◄’ and ‘►’ buttons to set the

number of pulses per revolution. Then press ’■’ to

confirm.

0.1 – 120 (0.1 Steps)

MAX PEED

Only available when output is set to SPEED.

Press ■’ and then use the ‘◄’ and ‘►’ buttons to set the

maximum Speed. Then press ’■’ to confirm.

0 – 400 km/h (1 km/h steps)

MAX VALUE

Only available when output is set to LAT ACC, LONG

ACC, PITCH, SLIP or ROLL

Press ’■’ and then use the ‘◄’ and ‘►’ buttons to set the

maximum value of that channel. Then press ’■’ to

confirm.

0 – 180o(1osteps) for Slip

0 – 90o(1osteps) for Pitch

0 – 90o(1osteps) for Roll

0.5 – 2 g (0.1 g steps) for LAT ACC

0.5 – 2 g (0.1 g steps) for LONG ACC

MAX FREQUENCY

Only available when output is set to LAT ACC, LONG

ACC, PITCH, SLIP or ROLL

Press ’■’ and then use the ‘◄’ and ‘►’ buttons to set the

maximum Frequency used on the digital output. Then

press ’■’ to confirm.

https://racelogic.support//01VBOX_data_loggers/VBOX_II_Range/VBOX_II_User_Guide/01_-_VBOX_II_Front_Panel

1 – 50 kHz (0.1 kHz steps)

TE T

Press ’■’ and then use the ‘◄’ and ‘►’ buttons to set a

test value that the Digital output will simulate. Then

press ’■’ to quit.

EXIT Press ’■’ to exit the setup menu and cause the settings

to be saved in EEPRO

https://racelogic.support//01VBOX_data_loggers/VBOX_II_Range/VBOX_II_User_Guide/01_-_VBOX_II_Front_Panel

Outputs: Analogue Setup enu (Channel 1 and 2)

OUTPUT

Press ’■’ and then use the ‘◄’ and ‘►’ buttons to

associate either of the following channels SPEED, SLIP

or PITCH, ROLL, LAT ACC and LONG ACC to the

Analogue output. Then press ’■’ to confirm.

VALUE @ +5V

Press ’■’ and then use the ‘◄’ and ‘►’ buttons to set the

value to represent +5 V. Then press ’■’ to confirm.

1 – 400 km/h (1 km/h steps)

–179oto 180o(0.1osteps) for Slip

-89oto 90o(1osteps) for Pitch

-89oto 90o(1osteps) for Roll

-1 to 2 g (0.1g steps) LAT ACC

-1 to 2 g (0.1g steps) LONG ACC

VALUE @ 0V

Only available when output is set to SPEED.

Press ’■’ and then use the ‘◄’ and ‘►’ buttons to set the

velocity to represent 0 V. Then press ’■’ to confirm.

0-399 km/h (1 km/h steps)

VALUE @ -5V

Only available when output is set to LAT ACC, LONG

ACC, PITCH, SLIP or ROLL.

Press ’■’ and then use the ‘◄’ and ‘►’ buttons to set the

value to represent -5 V. Then press ’■’ to confirm.

-2 to 1 g (0.1g steps) LAT ACC

-2 to 1 g (0.1g steps) LONG ACC

–180oto 179o(0.1osteps) for SLIP

-90oto 89o(1osteps) for PITCH

-90oto 89o(1osteps) for ROLL

https://racelogic.support//01VBOX_data_loggers/VBOX_II_Range/VBOX_II_User_Guide/01_-_VBOX_II_Front_Panel

Andere Handbücher für VBOX II

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Racelogic Datenlogger Handbücher

Racelogic

Racelogic VBOX II Bedienungsanleitung

Racelogic

Racelogic VBOX Micro Bedienungsanleitung

Racelogic

Racelogic VBOX Micro RLVBMIC01 Bedienungsanleitung

Racelogic

Racelogic VBOX 3i Bedienungsanleitung

Racelogic

Racelogic VBOX Touch V2 Bedienungsanleitung

Racelogic

Racelogic VBOX Touch Motorsport V2 Bedienungsanleitung

Racelogic

Racelogic VBOX Touch Bedienungsanleitung

Racelogic

Racelogic VBOX Touch Bedienungsanleitung

Racelogic

Racelogic Performance Box Touch V1 Bedienungsanleitung

Racelogic

Racelogic VB2SX Bedienungsanleitung

Racelogic

Racelogic VBOX IISX Bedienungsanleitung

Racelogic

Racelogic Performance Box Touch V1 Bedienungsanleitung

Racelogic

Racelogic VBOX II Bedienungsanleitung

Racelogic

Racelogic VBOX LapTimer Bedienungsanleitung

Racelogic

Racelogic VBOX Micro Bedienungsanleitung

Racelogic

Racelogic VBOX Touch Bedienungsanleitung

Racelogic

Racelogic VBOX Touch Bedienungsanleitung

Racelogic

Racelogic VBOX Touch V2 Bedienungsanleitung

Racelogic

Racelogic VBOX HD Lite Bedienungsanleitung

Racelogic

Racelogic VBOX SIGMA Bedienungsanleitung

Racelogic

Racelogic VBOX Touch Bedienungsanleitung

Racelogic

Racelogic Performance Box Touch V2 Bedienungsanleitung

Racelogic

Racelogic VBOX Touch v2 Bedienungsanleitung

Racelogic

Racelogic VBOX3i Bedienungsanleitung

Beliebte Datenlogger Handbücher anderer Marken

TESTO

TESTO 176 Bedienungsanleitung

HBM

HBM SOMAT XR CX22B-R Bedienungsanleitung

Agtrix

Agtrix 380i Bedienungsanleitung

Hobo

Hobo H8 Pro Bedienungsanleitung

Beijing ART Tech

Beijing ART Tech PCI2320 Bedienungsanleitung

Athena

Athena GET SL1 Bedienungsanleitung

Motec Systems

Motec Systems C185 Bedienungsanleitung

Beijing ART Tech

Beijing ART Tech USB2832 Bedienungsanleitung

HT Italia

HT Italia XL421 Bedienungsanleitung

Rotronic

Rotronic HygroLog HL20 Bedienungsanleitung

MRC

MRC DW-6092 Bedienungsanleitung

Edu-Logger

Edu-Logger 900-240 Bedienungsanleitung

Elma

Elma DT173 Bedienungsanleitung

MadgeTech

MadgeTech PRTemp140 Technisches Datenblatt

Comet

Comet U0121M Bedienungsanleitung

pico Technology

pico Technology PT-104 Bedienungsanleitung

Soil Instruments

Soil Instruments GTecLink Bedienungsanleitung

APLICOM

APLICOM A11 Bedienungsanleitung