Radial Engineering POWER-1 Bedienungsanleitung
Specications and appearance are subject to change without notice.
Copyright © 2021 Radial Engineering Ltd.
www.radialeng.com
Owner’sManual
Radial Engineering Ltd.
1845 Kingsway Ave, Port Coquitlam BC V3C 1S9
604-942-1001 • www.radialeng.com
True to the Music
Radial Engineering Ltd. Power-1 Owner’s Manual
INTRODUCTION
The Radial Power-1 rackmount power supply and surge suppressor gives musicians, engineers, producers,
studio owners, commercial facilities, and anyone working with valuable electronic equipment protection from
power surges that can damage or destroy music equipment instantaneously.
Unlike competitive products that utilize low quality MOV’s (Metal Oxide Varistors) for surge protection, Radial’s
Power-1 is built using a USA made MOV. This critical component has been proven to oer superior thermal
protection and have a much longer lifespan than the alternatives. An LED indicator on the front panel illuminates
when the MOV is active, giving you visual conrmation that your gear is protected from voltage spikes.
Created with audio professionals in mind, the Power-1 employs shunt mode technology and avoids passing
contaminated signals to the ground for lower system noise. Additionally, a high-rejection RF interference lter
is used to keep high frequencies and AM radio signals out of the power line, preventing contamination of audio
signals.
Eight rear panel outlets are provided (four with wall-wart spacing to accommodate any PSU size), along with
three front panel outlets and a USB charging port to easily power personal devices. A heavy-duty power on/o
toggle switch, rugged outlet connectors, and steel construction ensure that the Power-1 performs night after night
without fail.
3
Front USB
Power
Surge
Protect
Back
8
Noise
Filtering
BEFORE YOU GET STARTED
Thank you for purchasing the Radial Power-1 rackmount power supply unit. Before using the Power-1, please
read this short manual and heed all warnings and safety precautions listed. Your safety is our top priority! Should
you have any questions, please review the FAQ page for this product at www.radialeng.com, or contact us directly
Note: The Power-1 is a surge suppressor, meaning it blocks high voltage spikes that can damage connected
equipment. It does not, however, regulate or stabilize the incoming voltage; this is a task that requires a product
called an AC voltage regulator, and may be benecial for applications where unreliable or unsteady power
sources are employed.
True to the Music
Radial Engineering Ltd. Power-1 Owner’s Manual
1. FRONT PANEL OUTLETS: These outlets are always on, even when the front panel on/o switch is set to ‘o’. When using
the Power-1 as a power source for equipment racks, this allows you to easily connect and charge devices without powering on the
entire rack.
2. USB CHARGING PORT: 5V/1A USB charging port for mobile devices such as smartphones and tablets. Type-A USB connection.
3. FAULT PROTECTION INDICATOR: This LED illuminates when the Power-1’s Metal Oxide Varistor (MOV) is actively working,
providing fault protection against varying resistance and high-voltage spikes from the AC main power source. The MOV is designed
to recover from overvoltage events, providing continuous protection for your equipment. Should this LED turn o, immediately
remove the Power-1 from the AC main power source and contact Radial technical support for assistance.
4. ON/OFF: Large rocker switch with backlit LED activates the eight rear panel power outlets. Raised metal anges on either side of
this control help prevent accidental switching. If the Power-1 is connected to the AC main power source and the LED for the on/o
switch doesn’t illuminate, check the circuit breaker on the rear panel.
5. RACK EARS: Allow for mounting in standard 19” equipment racks, taking up 1 rack unit (1RU) of space.
6. POWER CABLE: Hardwired cable for connection to the AC main 120V power source.
7. CIRCUIT BREAKER: The Power-1 is rated for 15A of current, if this load is exceeded the circuit breaker will pop to help prevent
damage to the Power-1 and connected devices. Should the circuit breaker pop, unplug the Power-1 from the AC main power
source and press in the circuit breaker to reset it, then power back up as normal with a lower load connected to the Power-1.
8. REAR PANEL OUTLETS: Eight rear power outlets are provided, four with additional spacing in between each outlet to
accommodate for large ‘wall-wart’ power supplies. These power outlets are controlled by the front panel on/o switch.
FRONT & REAR PANEL FEATURES
3 4 5
678
2
1
SPECIFICATIONS*
IEC POWER PORTS
Voltage Rating: .....................................................................................120V, 50/60Hz
Load Rating: .........................................................................................15A total, 15A per outlet
USB POWER PORT
Voltage Rating: .....................................................................................5V
Load Rating: .........................................................................................1A
GENERAL
Overload Protection: .............................................................................American-made Metal Oxide Varistor (MOV), 15A circuit breaker
Dimensions (L x W x H): .......................................................................19” x 6.38” x 1.47” (482.6mm x 162.0mm x 37.4mm)
Temperature Range: .............................................................................5°C to 40°C
Agency Listings: ...................................................................................Conforms to UL Std 1419, 60950-1 and 60065 in USA,
CSA Std 60950-1, C22.2 No. 62368 in Canada
Warranty: ..............................................................................................Radial 3-year, transferable
*Specications are subject to change without notice.
True to the Music
Radial Engineering Ltd. Power-1 Owner’s ManualRadial Engineering Ltd. Power-1 Owner’s Manual
WARNING - IMPORTANT SAFETY INFORMATION
1. READ INSTRUCTIONS
All the safety and operating instructions of your Power-1 should be read before power is applied to the equipment. Retain this user
manual for future reference.
2. HEED WARNINGS AND OPERATING INSTRUCTIONS
All warnings on the equipment and operating instructions are important and should be followed.
3. HEAT, WATER AND MOISTURE
The equipment should be kept away from areas of high temperature, i.e., heater vents, radiators, stoves/ovens, replaces, etc. The
equipment should not be used in or around water, or in areas prone to ooding.
4. POWER SOURCES
The equipment should be connected only to a power source of the same voltage and frequency as that listed on the rear panel
above the power cord entry point.
5. POWER CORD PROTECTION
Power cords should be arranged so they do not interfere with the movement of objects in the room: people, fan blades, utility carts,
etc. Also, care should be taken that the cord is not pinched or cut, and placed so it is not in danger of being pinched or cut.
6. POWER CORD GROUNDING
The power supply cord is of a three wire grounded type, designed to reduce the risk of electric shock. It is assumed to be of suitable
length for most uses of the equipment. The use of extension cords and power strips is discouraged unless they are of suitable rating
to deliver the required total current for safe operation of all connected equipment. Furthermore, extension cords or power strips must
provide the same three wire grounded connection. It is important that the blades of the equipment’s plug be able to fully insert into the
mating receptacle. Never remove the round grounding pin on the plug in an attempt to mate to a two wire ungrounded receptacle.
7. NON-USE PERIODS
During periods of extended non-use, the power cord should be unplugged from the power source.
8. LIQUID ENTRY
Care should be taken so that liquids such as cleaning uids or beverages are not spilled into the enclosure of the equipment.
9. DAMAGE REQUIRING SERVICE
Equipment should be serviced by qualied service personnel when:
A. The power supply cord or plug has been damaged, B. Liquid has been spilled into the equipment, or the equipment has been
exposed to rain, C. The equipment has been dropped, or the enclosure has been damaged, or D. The PROTECT LED on the front
panel no longer illuminates when the equipment is connected to a power source.
10. NO USER ACCESSIBLE PARTS
The Power-1 has no user accessible parts inside the device and should only be serviced by a qualied technician.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS
EQUIPMENT TO RAIN OR MOISTURE.
NOTICE
Radial Engineering Ltd. shall under no circumstances be held responsible for any loss, damage or injury resulting
from the use of this product in a manner inconsistent with any of the procedures outlined in this document. The user is
responsible for determining whether this product is appropriate for the intended application. Radial Engineering Ltd. is
not responsible for any indirect, secondary or ancillary loss or damage, including personal injury, loss of or damage to
property or loss of income resulting from the operation or failure of this unit.
True to the Music
Radial Engineering Ltd. Power-1 Owner’s Manual
VERTISSEMENT - INFORMATIONS DE SÉCURITÉ IMPORTANTES
1. LIRE LES INSTRUCTIONS
Toutes les instructions de sécurité et d’utilisation de votre Power-1 doivent être lues avant de mettre l’équipement sous tension.
Conservez ce manuel de l’utilisateur pour référence future.
2. RESPECTER LES AVERTISSEMENTS ET LES INSTRUCTIONS D’UTILISATION
Tous les avertissements sur l’équipement et les instructions d’utilisation sont importants et doivent être suivis.
3. CHALEUR, EAU ET HUMIDITÉ
L’équipement doit être tenu à l’écart des zones à haute température, c’est-à-dire des évents de chauage, des radiateurs, des
cuisinières / fours, des cheminées, etc.
4. SOURCES D’ÉNERGIE
L’équipement doit être connecté uniquement à une source d’alimentation de même tension et fréquence que celle indiquée sur le
panneau arrière
au-dessus du point d’entrée du cordon d’alimentation.
5. PROTECTION DU CORDON D’ALIMENTATION
Les cordons d’alimentation doivent être disposés de manière à ne pas gêner le mouvement des objets dans la pièce: personnes, pales
de ventilateur, chariots utilitaires,
etc. Veillez également à ce que le cordon ne soit pas pincé ou coupé et placé de manière à ne pas risquer d’être pincé ou coupé.
6. MISE À LA TERRE DU CORDON D’ALIMENTATION
Le cordon d’alimentation est de type trois ls mis à la terre, conçu pour réduire le risque de choc électrique. Il est supposé être d’une
longueur appropriée pour la plupart des utilisations de l’équipement. L’utilisation de rallonges et de multiprises est déconseillée à
moins qu’elles ne soient d’un calibre approprié pour fournir le courant total requis pour un fonctionnement sûr de tous les équipements
connectés. De plus, les rallonges ou les barrettes d’alimentation doivent fournir la même connexion à la terre à trois ls. Il est important
que les lames de la che de l’équipement puissent s’insérer complètement dans la prise correspondante. Ne retirez jamais la broche
de mise à la terre ronde de la che pour tenter de se connecter à une prise à deux ls non mise à la terre.
7. PÉRIODES DE NON-UTILISATION
Pendant les périodes de non-utilisation prolongée, le cordon d’alimentation doit être débranché de la source d’alimentation.
8. ENTRÉE LIQUIDE
Des précautions doivent être prises pour que des liquides tels que des liquides de nettoyage ou des boissons ne soient pas renversés
dans l’enceinte de l’équipement.
9. DOMMAGES NÉCESSITANT UNE RÉPARATION
L’équipement doit être réparé par un personnel de service qualié lorsque:
A. Le cordon d’alimentation ou la che ont été endommagés, B.Un liquide a été renversé dans l’équipement, ou l’équipement a été
exposé à la pluie, C. L’équipement est tombé, ou le boîtier a été endommagé, ou D. Le Le voyant PROTECT sur le panneau avant ne
s’allume plus lorsque l’équipement est connecté à une source d’alimentation.
10. Aucune pièce accessible par l’utilisateur
Le Power-1 ne comporte aucune pièce accessible par l’utilisateur à l’intérieur de l’appareil et ne doit être entretenu que par un
technicien qualié.
L’ AVERTISSEMENT
RISQUE DE CHOC ÉLECTRIQUE
NE PAS OUVRIR
AVERTISSEMENT: POUR ÉVITER LES INCENDIES
OU LES CHOCS
DANGER, NE PAS EXPOSER CECI
ÉQUIPEMENT CONTRE LA PLUIE OU L’HUMIDITÉ.
L’ AVERTISSEMENT
Radial Engineering Ltd. ne pourra en aucun cas être tenu responsable de toute perte, dommage ou blessure résul-
tant de l’utilisation de ce produit d’une manière incompatible avec l’une des procédures décrites dans ce document.
L’utilisateur est responsable de déterminer si ce produit est adapté à l’application prévue. Radial Engineering Ltd. n’est
pas responsable de toute perte ou dommage indirect, secondaire ou accessoire, y compris les blessures corporelles, la
perte ou les dommages à la propriété ou la perte de revenu résultant du fonctionnement ou de la panne de cet appareil.
www.radialeng.com
Radial Power-1 Owner’s Manual v1.8
Specications and appearance are subject to change without notice.
RADIAL ENGINEERING LTD.
3 YEAR TRANSFERABLE WARRANTY
RADIAL ENGINEERING LTD. (“Radial”) warrants this product to be free from defects in material and work-
manship and will remedy any such defects free of charge according to the terms of this warranty. Radial will
repair or replace (at its option) any defective component(s) of this product (excluding nish and wear and
tear on components under normal use) for a period of three (3) years from the original date of purchase. In
the event that a particular product is no longer available, Radial reserves the right to replace the product
with a similar product of equal or greater value. To make a request or claim under this limited warranty, the
product must be returned prepaid in the original shipping container (or equivalent) to Radial or to an autho-
rized Radial repair center and you must assume the risk of loss or damage. A copy of the original invoice
showing date of purchase and the dealer name must accompany any request for work to be performed
under this limited and transferable warranty. This limited warranty shall not apply if the product has been
damaged due to abuse, misuse, misapplication, accident or as a result of service or modication by any
other than an authorized Radial repair center.
THERE ARE NO EXPRESSED WARRANTIES OTHER THAN THOSE ON THE FACE HEREOF AND DE-
SCRIBED ABOVE. NO WARRANTIES WHETHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT
LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE SHALL EXTEND BEYOND THE RESPECTIVE WARRANTY PERIOD DESCRIBED ABOVE
OF THREE YEARS. RADIAL SHALL NOT BE RESPONSIBLE OR LIABLE FOR ANY SPECIAL, INCIDEN-
TAL OR CONSEQUENTIAL DAMAGES OR LOSS ARISING FROM THE USE OF THIS PRODUCT. THIS
WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS,
WHICH MAY VARY DEPENDING ON WHERE YOU LIVE AND WHERE THE PRODUCT WAS PUR-
CHASED.
To meet the requirements of California Proposition 65, it is our responsibility to inform you of the following:
WARNING: This product contains chemicals known to the State of California to cause cancer, birth defects
or other reproductive harm.
Please take proper care when handling and consult local government regulations before discarding.
All trademarks belong to their respective owners. All references to these are for example only and are
not associated with Radial.
Radial Engineering Ltd.
1845 Kingsway Ave, Port Coquitlam BC V3C 1S9
604-942-1001 • www.radialeng.com
Inhaltsverzeichnis
Andere Radial Engineering Überspannungsschutz Handbücher
Beliebte Überspannungsschutz Handbücher anderer Marken
Leviton
Leviton 52412-DS3 Bedienungsanleitung
Savio
Savio LZ-07 Bedienungsanleitung
Siemens
Siemens HNM3M120 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric LITOL LTM-125RF Bedienungsanleitung
Intermatic
Intermatic PS3000 Bedienungsanleitung
ASCO POWER TECHNOLOGIES
ASCO POWER TECHNOLOGIES 360 Bedienungsanleitung