Radiant R1K 34 Bedienungsanleitung

R1K 34 - RAD - ING - Manuale - 1510.1_ErP

Installation, Use

and Maintenance Manual

for model

0476

R1K 34

Premix condensing system boiler

only heating

R1K 34 - RAD - ING - Manuale - 1510.1_ErP

2 Dati tecnici_R1K 34_ErP_EN

2. MAINTENANCE

SUPPORT CENTRE

2.2.8. TECHNICAL DATA

Model R1K 34

CE certification no. 0476CQ0134

Gas category II2H3B/P

Discharge type type B23p-B33-C13-C33-C43-C53-

C63-C83-C93

Energy efficiency 92/42 CEE no. stars 4

Energy efficiency EN13203-1 no. stars -

Maximum nominal heat capacity in heating circuit kW 34

Minimum nominal heat capacity in heating circuit kW 4.1

Useful thermal power - 60/80°C kW 33.35

Minimum useful thermal power - 60/80°C kW 3.94

Useful thermal power - 30/50°C kW 36.19

Performance at 100% Pn - 60/80°C % 98.08

Performance at 30% Pn - return 47°C % 102.14

Performance at 30% Pn - return 30°C % 108.57

Performance at 100% Pn - 30/50°C % 106.43

Maximum combustion Performance % 97.6

Fumes temperature at nominal heat capacity °C 71.93

CO2at nominal heat capacity % 9.6

CO2at minimum heat capacity % 8.84

CO2at nominal heat capacity - G30 % 11.55

CO2at minimum heat capacity - G30 % 10.8

CO2at nominal heat capacity - G31 % 10.32

CO2at minimum heat capacity - G31 % 9.89

CO at nominal heat capacity ppm 165

Fumes mass at nominal heat capacity g/s 14.96

Fumes mass at minimum heat capacity g/s 1.88

NOx class class 5

Heating circuit

Adjustable heating temperature °C 30-80 / 25-45

Maximum operating temperature for heating circuit °C 95

Maximum operating pressure for heating circuit bar 3

Minimum operating pressure for heating circuit bar 0.3

Capacity of the system expansion vessel litres 8

Dimensional characteristics

Width mm 410

Depth mm 330

Height mm 642

Gross weight Kg 40

Water connections

Flow Ø 3/4”

Cold water Ø 1/2”

Gas Ø 3/4”

R1K 34 - RAD - ING - Manuale - 1510.1_ErP

2 Dati tecnici_R1K 34_ErP_EN

2. MAINTENANCE

SUPPORT CENTRE

Return Ø 3/4”

Fume exhaust fittings

Maximum electric fan pressure available Pa 90.7

Max discharge length Ø80/125 - Hor Co-ax m 10

Max discharge length Ø80/80 - Hor Split m 15+15

Max discharge length Ø80/125 - Vert Co-ax m 10

Electrical specifications

Voltage-frequency V/Hz 220-230/50

Max Absorbed Power W 78

Insulation rate IP X5D

Gas supply

Nominal supply pressure - G20 mbar 20

Heating Max. fan speed - G20 Hz 186

Heating Min. fan speed - G20 Hz 45

Fuel consumption - G20 m3/h 3.60

Nominal Supply pressure - G30 mbar 28-30

Heating Max. fan speed - G30 Hz 176

Heating Min. fan speed - G30 Hz 45

Fuel consumption - G30 kg/h 2.68

Nominal Supply pressure - G31 mbar 37

Heating Max. fan speed - G31 Hz 184

Heating Min. fan speed - G31 Hz 45

Fuel consumption - G31 kg/h 2.64

R1K 34 - RAD - ING - Manuale - 1510.1_ErP

2 Complessivo tecnico_R1K 25_34_EN

2. MAINTENANCE

SUPPORT CENTRE

2.2.9. TECHNICAL ASSEMBLY

KEY

1. FUMES SAFETY THERMOFUSE

2. HEAT EXCHANGER

3. BURNER UNIT

4. DETECTION ELECTRODE

5. ELECTRIC FAN

6. AIR RELIEF VALVE

7. SAFETY VALVE 3 bar

8. CIRCULATOR

9. GAS VALVE

10. SYSTEM DRAINING TAP

11. SAFE T Y THERMOSTAT

12. HEATING PROBE

13. LIGHT UP ELECTRODE

14. EXPANSION TANK

15. START-UP TRANSFORMER

16. AIR SUCTION TUBE

17. PROPORTIONAL VENTURI

18. WATER PRESSURE SWITCH

19. CONDENSATE COLLECTION SIPHON

20. SYSTEM FILLING TAP

R1K 34 - RAD - ING - Manuale - 1510.1_ErP

2 Schema idraulico_R1K_EN

2. MAINTENANCE

SUPPORT CENTRE

2.2.10. HYDRAULIC BOARD

KEY

R. HEATING RETURN

G. GAS INLET

SC. CONDENSATE DRAIN

F. COLD WATER INLET

A. HEATING FORWARD

1. FUMES SAFETY THERMOFUSE

2. HEAT EXCHANGER

3. BURNER UNIT

4. ELECTRIC FAN

5. GAS VALVE

6. AIR RELIEF VALVE

7. CIRCUL ATOR

8. SAFETY VALVE 3 bar

9. SYSTEM DRAINING TAP

10. HEATING PROBE

11. SAFE T Y THERMOSTAT

12. EXPANSION TANK

13. AIR SUCTION TUBE

14. PROPORTIONAL VENTURI

15. WATER PRESSURE SWITCH

16. CONDENSATE COLLECTION SIPHON

17. BY-PASS

18. SYSTEM FILLING TAP

RFA

516

R1K 34 - RAD - ING - Manuale - 1510.1_ErP

3 Avvertenze generali per l'utilizzo_EN

3. USE

USER

3.1. USE

3.1.1. GENERAL USE WARNINGS

WARNING

Before starting the boiler the User must

make sure that the First start-up certificate has the

stamp of the technical Support Centre proving the

testing and the first start-up of the boiler.

WARNING

To validate the warranty, the boiler must

be started by a technical Support Centre authorized

by RADIANT no later than 30 days from the date of

installation.

WARNING

In order to take advantage of the guarantee

provided by the manufacturer, the customer should

carefully and exclusively observe the instructions

given in the USER section of the manual.

ATTENTION

This machine may be used only for the

purpose for which it has been designed: heat water

to a temperature below boiling point at atmospheric

pressure. Any other use is considered wrong and

dangerous. The manufacturer is excluded from

any contractual or out of contract responsibility for

damage caused to people, animals or property due

to incorrect use.

DANGER

The boiler should not be used by persons

(including children) with reduced physical, sensory or

mental capacities or without suitable knowledge or

experience unless they are instructed on the device

use or monitored by a person responsible for their

safety.

DANGER

DO NOT obstruct the air vents of the

location in which the gas device is installed to prevent

the formation of toxic explosive mixes.

DANGER

If you sense a gas odour in the location in

which the boiler is installed, proceed as follows:

› DO NOT use electrical switches, the telephone or

any other device that might generate electrical

discharges or sparks;

› Immediately open all doors and windows to

create an air exchange that can quickly clean

the location;

› Close the gas valves;

› Request immediate intervention of qualified

staff.

DANGER

The use of the electrical power boiler

implies respecting some fundamental rules such as:

› DO NOT touch the device with wet and/or humid

parts and/or with bare feet;

› DO NOT pull the electrical cables;

› DO NOT leave the device exposed to atmospheric

agents (rain, sun, etc.) unless specifically

intended;

› in case of cable damage, turn off the device and

contact qualified professional staff to replace it.

R1K 34 - RAD - ING - Manuale - 1510.1_ErP

3Pannellocomandi_solorisc_MIAH4_R2_G_EN

3. USE

USER

3.1.2. CONTROL PANEL

KEY

1. HEATING TEMPERATURE ADJUSTMENT

KEYS.

2. INFO KEY: PRESS ONCE TO VIEW THE

TEMPERATURES AND OTHER INFORMATION

(see chapter ‘INFO MENU DISPLAY) - HOLD

FOR 5 SECONDS, IN OFF OPERATING MODE,

TO VIEW THE LAST 5 FAULTS.

3. OPERATING MODE SELECTION KEY: ONLY

HEATING / OFF.

4. RESET KEY: FAULTS RESET - CHIMNEY

SWEEP FUNCTION ACTIVATION (HOLD FOR 7

SECONDS).

5. VALUE OF THE PARAMETERS ADJUSTMENT

KEY / HOLD THE KEYS AT THE SAME TIME

FOR 5 SECONDS TO ACTIVATE DISPLAY BACK

LIGHT FOR 10 MINUTES.

6. DISPLAY

2 3 4

R1K 34 - RAD - ING - Manuale - 1510.1_ErP

3 Icone del display_solo risc_MIAH4_EN

3. USE

USER

3.1.3. DISPLAY ICONS

KEY

1. INDICATION OF PARAMETER NUMBER OR

DISPLAYED INFO CODE

2. PARAMETERS PROGRAMMING FUNCTION

ACTIVE

3. SIGNALLING CONNECTED SOLAR BOARD /

SOLAR COLLECTOR TEMPERATURE DISPLAY

(d5)

4. SOLAR PUMP ACTIVE

5. BOILER LOWER TEMPERATURE DISPLAY (d6)

/ BOILER UPPER TEMPERATURE DISPLAY

(d7)

6. EXTERNAL PROBE INSTALLED / EXTERNAL

PROBE TEMPERATURE (d1)

7. TEMPERATURE DISPLAY / SET POINT /

PARAMETER VALUE

8. OPEN THERM COMMUNICATION PRESENT

(REMOTE CONTROL / AREA CONTROL UNIT)

9. INSUFFICIENT SYSTEM WATER PRESSURE

SIGNALLING

10. FLAME PRESENT SIGNALLING / IT ALSO

INDICATES, ON 3 PERCENTAGE LEVELS, THE

MODULATING POWER LEVEL OF THE BOILER

(fig.2)

11. ERROR DISPLAY THAT CAN BE RESET

12. OFF OPERATING MODE

13. ERROR DISPLAY THAT CAN NOT BE RESET

14. OPERATION IN HEATING MODE ENABLED

456 7

111213

≤ 33% >33%<66% >66%<100%

fig. 1

fig. 2

R1K 34 - RAD - ING - Manuale - 1510.1_ErP

3 Visualizzazioni del menù Info_MIAH4_EN

3. USE

USER

3.1.4. INFO MENU DISPLAY DATA

To view the boiler data from info menu you just have to press the INFO ‘ ’ key. The info code will be

displayed on the left side of the screen and its relative value will be displayed on the centre of the screen.

Use keys ‘ ’ and ‘ ’ of the heating circuit to scroll through the list of displayed data. To exit display

mode press the INFO ‘ ’ key.

LIST OF DISPLAYED DATA

INFO CODE ICON DESCRIPTION

d0 DOMESTIC CIRCUIT PROBE TEMPERATURE

d1 EXTERNAL PROBE TEMPERATURE

d2 FAN SPEED

d3 BOTTOM AREA PROBE TEMPERATURE [IF AREA BOARD INSTALLED]

d4 RETURN PROBE TEMPERATURE

d5 SOLAR COLLECTOR TEMPERATURE [IF SOLAR BOARD INSTALLED] (SCS)

d6 SOLAR BOILER TEMPERATURE (BOTTOM) [IF SOLAR BOARD INSTALLED] (SBSI)

d7 SOLAR BOILER TEMPERATURE (TOP) [IF SOLAR BOARD INSTALLED] (SBSS)

d8 SOLAR COLLECTOR PROBE TEMPERATURE 2 [IF SOLAR BOARD INSTALLED] (SCS2)

d9 EXTRA SOLAR BOILER TEMPERATURE [IF SOLAR BOARD INSTALLED] (SBS3)

R1K 34 - RAD - ING - Manuale - 1510.1_ErP

3Accensione_Modalitàdifunzionamento_Antigelo_solorisc_MIAH4_MIAH6_EN

3. USE

USER

3.1.5. START-UP

Before starting the boiler make sure that it is

powered and that the gas tap below the boiler is

open.

To start the boiler press the function key ‘

’ and select the desired operating mode. If the

symbol is displayed fixed, it means that the function

was activated.

3.1.6. OPERATING MODE

ONLY HEATING MODE

In this mode the boiler meets only the demands of

heating.

To switch the boiler to ONLY HEATING operating

mode, press the function key ‘ ’, the symbol ‘

’ will appear fixed on the display, indicating that

the function is enabled.

Whenever heating energy is needed to heat the

rooms the automatic start-up system will start the

burner; this is indicated by displaying the symbol ‘

’ blinking.

ADJUSTING THE HEATING TEMPERATURE

You can adjust the temperature using keys ‘ ’

and ‘ ’ of the heating circuit :

· press key ‘ ’ to decrease the temperature.

· press key ‘ ’ to increase the temperature.

The heating temperature adjustment field ranges

from 30 °C to 80 °C (25 °C – 45 °C for floor systems).

OFF MODE

In this mode the boiler no longer meets the heating

demands, the anti-freeze and pump anti-locking

systems still remain active.

To switch the boiler to OFF operating mode, press

the function key ‘ ’, the symbol ‘ ’ will

appear fixed on the display, indicating that the

function is enabled (for non condensing models

will appear the message ‘OFF’).

If the boiler was previously r unning, it will be turned

off and the post-ventilation and post-circulation

functions will be enabled.

If you have to deactivate the boiler for a long period

of time, proceed as follows:

› contact the Technical support centre that will

empty the water system, where no anti-freeze

is intended, and will cut off the power, water and

gas supply.

› Or leave the boiler in OFF operating mode

keeping active the electrical and gas supplies so

that the anti-freeze function may activate.

Andere Handbücher für R1K 34

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Radiant Kessel Handbücher

Radiant

Radiant R2KA 28/20 Kurzanleitung

Radiant

Radiant RK 18 Bedienungsanleitung

Radiant

Radiant RKR 25 Bedienungsanleitung

Radiant

Radiant RSA 24 /8 Bedienungsanleitung

Radiant

Radiant RAIN 30 E Bedienungsanleitung

Radiant

Radiant RMA Bedienungsanleitung

Radiant

Radiant R1K 34 Bedienungsanleitung

Radiant

Radiant R2K 34 RAIN Handbuch

Radiant

Radiant R2K 24 Handbuch

Radiant

Radiant R1K 25 RAIN Handbuch

Radiant

Radiant RKA 25 Bedienungsanleitung

Radiant

Radiant R2KA 34 Service-Handbuch

Radiant

Radiant RK 100 Bedienungsanleitung

Radiant

Radiant RMAS 21 E Bedienungsanleitung

Radiant

Radiant RKA 25 Bedienungsanleitung

Radiant

Radiant R1CR 24 Bedienungsanleitung

Radiant

Radiant R2K 34 RAIN Montageanleitung

Radiant

Radiant R1K 50 Handbuch

Radiant

Radiant RSF 30 E Handbuch

Radiant

Radiant R1KR Service-Handbuch

Radiant

Radiant R1C 34/B Service-Handbuch

Radiant

Radiant RSF 24 E Handbuch

Radiant

Radiant RMAS 21 E Handbuch

Radiant

Radiant RBS 24 Handbuch

Beliebte Kessel Handbücher anderer Marken

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Bedienungsanleitung

Radijator

Radijator BIO max 23.1 Bedienungsanleitung

Brunner

Brunner BSV 20 Bedienungsanleitung

Buderus

Buderus Logamax GB062-24 KDE H V2 Bedienungsanleitung

Potterton

Potterton 50e Datenblatt

UTICA BOILERS

UTICA BOILERS TriFire Bedienungsanleitung

Joannes

Joannes LADY Series Handbuch

ECR International

ECR International UB90-125 Gebrauchsanweisung

Froling

Froling FHG Turbo 3000 Bedienungsanleitung

Froling

Froling P4 Pellet 8 - 105 Bedienungsanleitung

U.S. Boiler Company

U.S. Boiler Company K2 Bedienungsanleitung

Henrad

Henrad C95 FF Bedienungsanleitung

NeOvo

NeOvo EcoNox EF 36 Bedienungsanleitung

Potterton

Potterton PROMAX SL 12 Bedienungsanleitung

Eco Hometec

Eco Hometec EC 25 COMPACT Bedienungsanleitung

Viessmann

Viessmann VITODENS 200 Leitfaden

Baxi

Baxi Prime 1.24 Bedienungsanleitung

REXNOVA

REXNOVA ISA 20 BITHERMAL Bedienungsanleitung