Radio Shack 49-2534 Bedienungsanleitung

RadioShack and RadioShack.com are trademarks

used by RadioShack Corporation.

49-2534

OWNER’S MANUAL — Please read before using this equipment.

Thank you for purchasing the RadioShack 2.4 GHz

Wireless Surveillance System. This system adds safety and

security to your home or business. It can be used as a

component of an audio/video observation system, or

expanded by adding up to three additional wireless

cameras. The audio/video jacks let you connect to a VCR

for recording purposes. In your home, you can observe your

baby’s room, backyard, or patio area at night or in minimal

lighting. In your business, monitor low-light store-rooms,

warehouses, entry/exit-ways, or a reception area from one

central location.

Built-InOne-WayMicrophoneand

Speaker— lets you hear your baby

or individuals near the camera.

Auto-Focus Lens — focuses

image automatically without

manual adjustment.

CMOS Sensor — provides

superior resolution even in low-

light conditions.

Built-in 8 LED Lighting —

enhances low light viewing at

two meters distance.

Long Distance

Monitoring — transmits

up to 300 feet clear-line-

of-sight.

Screen On/Off Switch —

lets you turn off the screen

for audio monitoring only.

Portable and Easy To

Install– lets you take or

install the system virtually

anywhere.

%106'065

Important Safety Precautions ..... 2

Installing The Batteries ............... 2

In the Camera ......................... 3

In the Monitor .......................... 4

Installation .................................. 4

Desk Mounting the Camera .... 5

Wall Mounting the Camera ..... 5

Setting Up Your System ............. 5

Setting Up the Camera ........... 5

Setting Up the Monitor ............ 5

Audio Output......................... 6

Video Output......................... 6

Orienting Antennas for Optimal

Performance ........................... 7

Setting the Auto-Switching

Sequence ................................ 8

Monitor to A/V function ............ 8

Night Vision ............................. 8

Troubleshooting ......................... 9

The FCC Wants You To Know .... 9

Care ......................................... 10

Service and Repair ................... 10

Specifications ............................ 11

#"+/2146#06"#

If an icon appears at the end of a

paragraph, go to the box on that

page with the corresponding icon

for pertinent information.

Rý— Warning #— Important

.— Caution ±— Note

406")*\"9KTGNGUU"5WTXGKNNCPEG"5[UVGO

+/2146#06"5#('6;"

24'%#76+105"

Before setting up or operating your system, please read all

these safety and operating instructions completely. Retain

instructions for future reference.

To avoid entanglement, never place the camera in a crib or

playpen.

Do not place or mount the camera on any surface or wall

where the camera and its AC adapter cord are within the

reach of a baby or other children.

Never use the camera or monitor near water. For example,

do not use near a bathtub, washbowl, laundry tub, kitchen

sink, aquarium, or in a wet basement.

Disconnect the AC adapters from wall outlets during long

periods of non-use.

Position the camera, monitor and AC adapters to allow

adequate ventilation.

Keep the camera out of direct sunlight.

To prevent overheating, keep the camera, monitor and AC

adapters away from heat sources such as radiators, heat

registers, stoves or other appliances (including amplifiers)

which produce heat.

Use only the AC adapters provided. Use of any others may

damage the camera and/or monitor.R

Plug into an electrical outlet with standard household power

(120 volt AC outlet).

Changes or modifications not approved by RadioShack void

the manufacturer’s warranty and could void user's authority

to operate the equipment.

+056#..+0)"6*'"$#66'4+'5

Both camera and monitor are battery powered so they can

work during a power failure. To activate the battery power,

you must disconnect the AC adapters from both the camera

and monitor. For optimum performance, we recommend

alkaline batteries (available at your local RadioShack store).

The battery power lasts eight hours for the camera and 2.5

hours for the monitor.±

2#%-#)'"

%106'065

Please check that you have these

components before installation.

• A camera with built-in

transmitter

• A monitor with built-in receiver

• A 9V AC adapter (for camera

only)

• A larger 13.5V AC adapter (for

monitor only)

The lightning symbol is intended to alert you to

the presence of uninsulated dangerous voltage

withinthis product’s enclosure that might be of

sufficient magnitude to constitute a risk of

electric shock. Do not open the product’s case.

The exclamation symbol is intended to inform

you that important operating and maintenance

instructions are included in the literature

accompanying this product.

WARNING: To reduce the risk of fire or shock

hazard, do not expose this product to rain or

moisture. ..CAUTION..

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER OR BACK. NO

USER-SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED PERSONNEL.

RISKOF ELECTRIC SHOCK

DO NOT OPEN

R"9#40+0)"R

Two AC adapters are included

with the Wireless Surveillance

System. The AC adapters can not

be interchanged. Use the adapter

labeled OUTPUT: 9V DC for the

camera. Use the larger adapter

labeled OUTPUT: 13.5V DC for

the monitor.

±"016'"±"

When the baby monitor’s sound

weakens or the picture becomes

unsteady while operating with

batteries, replace the batteries.

+0"6*'"%#/'4#

1. Turn the camera upside-down.

2. Use your thumbs to press the top of the battery

compartment cover in the direction indicated by the

arrows to lift off the cover.

3. Install eight AA batteries (notsupplied) according to the

battery polarities marked inside of the battery

compartment..

4. Replace the battery compartment cover.

."%#76+10".

• Use only fresh batteries of the

required size and

recommended type.

• Do not mix old and new

batteries, different types of

batteries (standard, alkaline, or

rechargeable), or rechargeable

batteries of different capacities.

• If you do not plan to use the

system with batteries for an

extended period, remove the

batteries. Batteries can leak

chemicals that can destroy

electronic parts.

+0"6*'"/10+614

1. Turn the monitor upside-down.

2. Use your thumbs to press the dotted area on the

battery compartment cover in the direction illustrated to

open the cover.

3. Install 10 C cell batteries (not supplied) according to the

battery polarities marked inside the compartment.

4. Replace the battery compartment cover.R

+056#..#6+10

Select a locationfor the camera that provides a clear view of

the area you want to monitor, and that is free from dust. The

location should not be in line-of-sight with a strong light

source or in direct sunlight.

Have a person hold the camera against the wall at the

selected mounting area, while another person moves the

monitor to various locations throughout the house to check

reception. If interference or other problems develop, refer to

R"9#40+0)"R

Dispose of old batteries promptly

and properly. Do not burn or bury

them.

“Troubleshooting” on Page 9. You may need to select a

different location in the room for mounting the camera.

&'5-"/1706+0)"6*'"%#/'4#

You can place the camera on a desk or any level surface.

Select a location that is near an AC outlet and within the

reach of the AC adapter cord.±

9#.."/1706+0)"6*'"%#/'4#

1. Test the reception ofthe videomonitor before installing.

2. Drive a screw (not supplied) on the wall. Let the head

extend 5 mm (3/16 inch) from the wall.

3. Hang the camera and make sure it is securely

mounted.

4. Adjust the camera to the best viewing angle.

5'66+0)"72";174"5;56'/

Set the camera and monitor to the same channel (1, 2, 3 or

4) using the CHANNEL 1 2 3 4 dip switches on the back of the

camera and the CH. 1 2 3 4 5 dip switches on the back of the

monitor.#

5'66+0)"72"6*'"%#/'4#

It is possible for the monitor to pick up sounds or display

interference from other signal producing devices. To

minimize such potential problems, four channels are

available for use. Make sure that the camera and monitor

are set to the same channel.

1. Plug the small AC adapter cord into the 9V DC socket

on the back of the camera.

2. Plug the AC adapter into a standard wall outlet.

3. Slide the ON/OFF/NIGHT switch on the rear of the

camera to ON. The power indicator lights.

4. Position the camera antenna so its curved side points

to the monitor antenna’s curved side.

5'66+0)"72"6*'"/10+614

It is possible for the monitor to pick-up sounds or picture

interference from other signal producing devices. To

minimize this potential problem, experiment setting the

±"016'"±"

The camera bracket does not freely

rotate a full 360 degrees.

#"+/2146#06"#

Sound and video may be

broadcast to other 2.4 GHz

receiving devices. Conversations,

even from rooms near the camera,

may be broadcast. To protect the

privacy of your home, always turn

the camera off when not in use.

CH. 1 2 3 4 5 dip switches in different positions and use the

setting which produces the best sound and picture. Make

sure that the camera and monitor are set to the same

channel.

Dip switches 1to 4are for channel selection. Switch 5lets

you set up the auto-sequence timer for four cameras on four

different channels to monitor a series of rooms for maximum

supervision of the house (or office).±

1. Plug the large AC adapter cord into the DC 13.5V jack

on rear left of the monitor.

2. Plug the AC adapter into a standard wall outlet.

3. Rotate the monitor’s VOL ON/OFF clockwise to turn on

the monitor and adjust volume to a comfortable

listening level.

4. Adjust the video image using V-HOLD (Vertical Hold),

CONT (Contrast) and BRIGHT (Brightness) on the rear

right of the monitor.

5. Locate and orient the antennas on both the camera and

monitor according to “Orienting Antennas for Optimal

Performance” on Page 7.

#WFKQ"1WVRWV

To transfer the monitor’s sound to a TV or to a VCR for

recording purposes, connect the monitor’s AUDIO OUTPUT

to a TV’s or VCR’s audio input.

8KFGQ"1WVRWV

Connect the monitor’s VIDEO OUTPUT to a TV’s or VCR’s

video input for a large screen display, or to record

transmissions.

±"016'"±"

Your Wireless Surveillance System

is factory preset at channel 1 for

one camera use.

14+'06+0)"#06'00#5"(14"126+/#."

2'4(14/#0%'

This system broadcasts its high-quality audio and video

using directional antennas, which must be oriented in

certain configurations for best results. The 2.4 GHz

antennas have been designed to pivot and have limited

rotation in either clockwise or counterclockwise

directions.R

In most situations, the curved side of the antennas on both

the camera and monitor should face toward one another.

Since all rooms are different, for optimal reception,

additional slight pivots or rotations might be necessary. If

the camera and monitor are less than 10 feet (3 meters)

apart, keep the antennas flat in their casings.

R"9#40+0)"R

Rotating the antennas beyond the

point where resistance is felt will

result in permanent damage to

both antennas and the mechanical

stop. The antennas do not freely

rotate a full 360 degrees.

5'66+0)"6*'"#761/59+6%*+0)"

5'37'0%'

You can install up to four cameras on four different channels

to monitor a series of rooms for maximum supervision of the

house (or office). The monitor can automatically switch

between the four cameras. To activate the auto-switch

function, you must set the dip-switches.

To cancel the auto-switch sequence and lock on one

channel, set the dip-switch for the channel you want to

receive to ON. Slide the others to OFF.

/10+614"61"#18"(70%6+10

The system’s monitor unit has audio/video outputs to

transfer the picture and sound from the monitor screen to a

TV for a large screen display. Connect the monitor’s AUDIO/

VIDEO OUTPUT to a TV’s A/V input, or to a VCR to record

transmissions. You can find a full selection of A/V cable and

connectors at your local RadioShack store.

0+)*6"8+5+10

The camera has eight high-intensity LEDs (Light Emitting

Diodes) for picking up clear images in dark locations.

To turn on the night vision function, slide the

ON/OFF/NIGHT to NIGHT.±

&KR"5YKVEJ 1P 1HH

1 Channel 1 enabled Channel 1 disabled

2Channel 2 enabled Channel 2 disabled

3 Channel 3 enabled Channel 3 disabled

4Channel 4 enabled Channel 4 disabled

5Eight second

interval in display

rotation

Four second interval

in display rotation

±"016'"±"

The video image displayed on the

monitor may appear “snowy” when

the camera is operating in

darkness or very low levels of light.

6417$.'5*116+0)

6*'"(%%"9#065";17"61"

-019

Your camera and monitor might cause interference on other

radio/TV devices even when they areoperating properly. To

determine whether your camera or monitor is causing the

interference, turn them both off. If the interference goes

away, your surveillance system is causing it. Try to

eliminate the interference by:

• Moving your camera or monitor away from the other

device.

• Connecting your camera or monitor to an outlet that is

on a different electrical circuit from the other device.

• Contacting your local RadioShack store for help.

5[ORVQOU %JGEM"2QKPVU

No power is supplied to the

camera or monitor

Is the power cord disconnected?

Connect it.

The wrong AC adapter was used.

Use the AC adapter labeled

OUTPUT: 9V with the camera,

13.5V with the monitor.

Camera/Monitor is not turned on.

Set the power switch to the “ON”

position.

No sound or picture. Noisy

sound or picture.

Channel switches are not on the

same setting. Set the camera and

the monitor to same channel.

Signal interference due to

microwave oven. Turn off the oven

or remove it from path between

camera and monitor.

Signal interference due to other

signal producing devices. Change

the channel setting on both the

camera and the monitor. Identify

and eliminate the source of

interference. Relocate the camera

and/or monitor.

Out of range. Relocate the

camera and/or monitor within the

300 feet range.

Improper antenna position. Adjust

camera/monitor antenna

orientation.

If you cannot eliminate the interference, the FCC requires

that you stop using your system.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including

interference that may cause undesired operation.

%#4'

Keep the camera and monitor dry; if they get wet, wipe them

dry immediately. Use and store the camera and monitor

only in normal temperature environments. Handle them

carefully; do not drop them. Keep the camera and monitor

away from dust and dirt, and wipe them with a damp cloth

occasionally to keep them looking new.

5'48+%'"#0&"4'2#+4

If your camera or monitor is not performing as it should, take

it to your local RadioShack store for assistance. Modifying

or tampering with the camera’s or monitor’s internal

components can cause a malfunction and might invalidate

their warranty and void your FCC authorization to operate

them.

Inhaltsverzeichnis

Andere Radio Shack Sicherheitssystem Handbücher

Radio Shack

Radio Shack 65572 Bedienungsanleitung

Radio Shack

Radio Shack Wireless Key-Lock Door/Window Alarm 49-118 Bedienungsanleitung

Radio Shack

Radio Shack RS-3000 Bedienungsanleitung

Radio Shack

Radio Shack 49-1011 Bedienungsanleitung

Radio Shack

Radio Shack 49-418 Bedienungsanleitung

Radio Shack

Radio Shack 49-2551A Bedienungsanleitung

Radio Shack

Radio Shack 65562 Bedienungsanleitung

Radio Shack

Radio Shack CENTRAL 2000 49-351 Bedienungsanleitung

Radio Shack

Radio Shack RS-2000 Bedienungsanleitung

Radio Shack

Radio Shack Passive Bedienungsanleitung

Radio Shack

Radio Shack CENTRAL 49-2570 Bedienungsanleitung

Radio Shack

Radio Shack Two-Zone Burglar Alarm System Bedienungsanleitung

Radio Shack

Radio Shack RS-1000 Bedienungsanleitung

Radio Shack

Radio Shack CENTRAL 5000 49-2570 Bedienungsanleitung

Radio Shack

Radio Shack 49-1010 Bedienungsanleitung

Radio Shack

Radio Shack Invisible Beam Entry Alert Bedienungsanleitung

Radio Shack

Radio Shack 49-1000 Bedienungsanleitung

Radio Shack

Radio Shack 49-421A Bedienungsanleitung

Radio Shack

Radio Shack 49-2513 Bedienungsanleitung

Radio Shack

Radio Shack 49-1000 Bedienungsanleitung

Radio Shack

Radio Shack Self-Stick Door/Window Alarm Bedienungsanleitung

Radio Shack

Radio Shack 49-1020 Bedienungsanleitung

Radio Shack

Radio Shack RS-4000 Bedienungsanleitung

Radio Shack

Radio Shack 49-415 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

DSC

DSC PC 4010 Betriebsanleitung

UniPOS

UniPOS 6202L Bedienungsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Rondish

Rondish Nexus Bedienungsanleitung