Radio Shack Speaker Bedienungsanleitung

Portable 900 MHz Wireless Speaker System

Thank you for purchasing the RCA

Portable 900 MHz Wireless Speaker

System. Your system gives you high-quality

stereo sound in the 900 MHz band to

almost anywhere in or around your home.

Your Speaker System's three selectable

channels, PLL (Phase-Locked Loop)

circuitry and built-in antenna give you

precise tuning, so you can enjoy your

favorite music while you exercise or work

around your yard or house — up to 300

feet away from your stereo.

Your system has compander circuitry for

optimum dynamic range and noise

reduction, a 10-watt RMS amplifier in each

speaker, a 2-way speaker design with 5"

woofer and 1" dome tweeter. It has true

stereo operation with frequency ranges

from 50Hz to 20KHz (6dB bandwidth),

which will offer you the best sound. There

is no pilot tone spill over in this system,

and this improves your sound quality.

Also there is Automatic Level Control for

audio input to RF transmitter for optimum

FM deviation adjustment (plug and play,

no user adjustment is required)

Power/Transmitter Indicator — lights

green when the AC adapter is correctly

plugged in and the audio signal is input to

the transmitter.

Power/Speaker Indicator — lights green

when the AC adapter is correctly plugged

in or batteries are installed and POWER is

set to ON.

Your system is powered by three AC

adapters (included) or 16 “D” batteries (not

supplied, 8 for each speaker)

Getting Started

Your package should contain the following items

Installing the Transmitter

Choosing a Location

In order to achieve the best performance,

position the transmitter as far as possible

from other electronic devices such as TVs,

receivers, or VCRs. Radio interference from

these devices could affect your system's

performance.

Position the transmitter away from large

metal objects, as these could block your

transmitter's signals. Try several locations

for the transmitter. Select the location that

provides the best performance. Set up the

transmitter to send a wireless signal to the

speakers.

Connecting to AC Power

Connect the transmitter to AC power with

the supplied 12V, 250mA AC adapter. Plug

the supplied AC adapter's barrel plug into

the transmitter's DC 12V jack, then plug the

adapter into a standard AC outlet.

Cautions:

• You must use a Class 2 power source

that supplies 12 volts DC and delivers

at least 250mA. Its center tip must be

set to positive and its plug must fit the

transmitter's DC 12V jack. The supplied

adapter meets these specifications.

Using an adapter that does not meet

these specifications will damage the

transmitter or the adapter.

• Always connect the AC adapter to the

transmitter before you connect it to AC

power. When you finish, disconnect the

adapter from AC power before you

disconnect it from the transmitter.

Package Contents

Transmitter (1) Speaker (2)

AC Adapter for Transmitter (1) AC Adapter for Speaker (2)

Dual RCA Male to Dual RCA Male Cable (1) 1/8-inch Stereo Male to Dual RCA Female

Adapter (1)

3-foot Cable with 1/8-inch Stereo Male to Dual 1/8-inch Stereo Female (1)

DC 12V Jack

CHANNEL

1 2 3 STEREO/

MONO

AUDIOIN

L/R

Connecting to an Audio Source

You can connect the transmitter to your

audio source's left and right audio output

jacks or its headphone jack.

Cautions:

• Do not connect the transmitter to your

audio source's speaker output. Doing so

could damage the transmitter and the

audio source.

• If you connected the transmitter to an

audio source's headphone jack, set the

audio source's volume control to its

middle-position.

1. Connect one end of the supplied audio

patch cord to the transmitter's audio

jacks (white plug to L AUDIO IN and

red plug to R AUDIO IN).

2. If you are using the audio source's output

jacks, connect the white and red plugs

at the other end of the patch cord

directly to the audio source's

corresponding left (white) and right

(red) audio jacks.

If you are using your audio source's stereo

headphone jack, connect the patch cord's

white and red plugs to the white and

red phono jacks on the phono side of

the 1/8-inch supplied adapter.

If your audio source has a 1/8-inch

headphone jack, insert the adapter's 1/8-

inch stereo plug into the audio source's

HEADPHONE jack.

Mode Switch

For normal stereo use, set STEREO/MONO,

on the back of the transmitter, to STEREO.

If you are using a monaural system, set

STEREO/MONO to MONO.

Installing a Speaker

Connecting Power

Installing Batteries

You can use 16 (8 for each speaker) D size

batteries (not supplied) to power the

speakers. Batteries are available at your local

RadioShack store or online at

www.radioshack.com.

Battery Notes:

• Use only fresh batteries of the required

size and recommended type.

• Do not mix old and new batteries,

different types of batteries (standard,

alkaline, or rechargeable), or

rechargeable batteries of different

capacities.

• If you do not plan to use the speakers

for a week or longer, remove the

batteries. Batteries can leak chemicals

that can destroy electronic parts.

• Dispose of old batteries promptly and

properly.

• Do not burn or bury batteries.

1. Press the two tabs located on the back

of the speaker and open the battery

compartment cover.

2. Insert the batteries in the compartment

according to the polarity symbols (+

and –) marked inside the battery

compartment.

3. Replace the battery compartment cover

and make sure the cover is secured

prior to moving the speaker.

Notes

• Unpluging the supplied AC adapter

causes the batteries to automatically

power the speaker.

• When the AC adapter is used, the

batteries are automatically disconnected

from the speaker.

• When the speakers POWER LED

blinks, replace the batteries.

Keyhole Slot

Strain Relief

Slot

Battery

Compartment

Cover

8 D Size Batteries

Battery

Compartment

Cover

Connecting AC Power

1. Insert the supplied 12V, 1800mA AC

adapter’s barrel plug into the DC 12V

jack located at the back of the speaker.

2. Plug the other end of the AC Adapter

into an AC wall outlet.

3. Route the adapter’s cord through the

strain relief slot on the back of the

speaker.

Repeat the above steps for the other speaker.

Mounting the Speakers

To mount a speaker on the wall, you need a

screw (not supplied) with a head that fits

into the keyhole slot on the back of the

speaker.

1. Select a location and drill a hole at the

location.

2. Thread a screw into the hole until the

screw’s head extends about 15mm from

the wall.

3. Align the keyhole on the speaker with

the screw head in the wall, then slide

the speaker downward to secure it.

Using Your System with Your PC

Follow these steps to use your speakers with your computer.

1. Connect the male end of the supplied cable adapter (1/8-inch stereo male to dual-1/8-inch

stereo female cable) to your computer’s audio output jack. Connect one of the cable ends

to your existing computer speaker plug and connect the other unused 1/8-inch female

cable end to the supplied Y-Adapter (1/8-inch stereo male to Dual-RCA female adapter).

2. Connect one end of the RCA adapter (Dual RCA-to-RCA) to the white and red phono

jacks on the phono side of the Y-adapter (1/8-inch stereo male to Dual-RCA female

adapter).

3. Connect the RCA Adapter’s (Dual RCA-to-RCA) left (white) cable end to the transmitter’s

LAUDIOINjack and the right (red) cable end to the transmitter’s R AUDIO IN jack.

Operation

Listening Safety

To protect your hearing, follow these

guidelines when you use the speaker system.

• Set the volume to the lowest setting

before you begin listening. After you

begin listening, adjust the volume to a

comfortable level.

• Do not listen at extremely high volume

levels. Extended high-volume listening

can lead to permanent hearing loss.

• Once you set the volume, do not

increase it. Over time, your ears adapt

to the volume level, so a volume level

that does not cause discomfort might

still damage your hearing.

Using Your Speakers

Follow these steps to obtain maximum

listening performance:

1. Turn on your audio source.

See Transmitter AUTO ON/OFF below

for the transmitter operation.

2. Set the transmitter to a frequency

channel (CHANNEL 1, 2, or 3) that has

no interference.

Slide CHANNEL 1 2 3 at the rear of the

speakers to select the same channel

selected on the transmitter.

3. Turn on each speaker (Left and Right

speakers) by rotating POWER from

OFF to ON. You hear a click and the

power indicator lights green.

4. Set SPEAKER on the back of each

speaker to either L(for the Left stereo

speaker) or R(for the Right stereo

speaker).

5. Adjust VOLUME and BASS on each

speaker between MIN (minimum) to

MAX (maximum) to a comfortable

listening level.

6. To turn off each speaker, rotate POWER

from ON to OFF. The power indicator

turns off.

Transmitter AUTO ON/OFF

The transmitter has a built-in automatic

transmit ON/OFF controller. When the AC

adapter is correctly plugged in and the

transmitter receives audio signals from the

audio source, the transmitter’s power LED

lights green. The transmission stops if the

transmitter does not receive audio signals

from the audio source for about one minute.

The transmitter’s power LED turns off when

the transmitter does not receive audio

signals.

Channel Select

If you receive interference, try changing the

channel number on the transmitter and the

speakers.

Care

Keep the system dry; if it gets wet, wipe it

dry immediately. Use and store the system

only in normal temperature environments.

Handle the system carefully; do not drop it.

Keep the system away from dust and dirt,

and wipe it with a damp cloth occasionally

to keep it looking new.

Caution: You might permanently damage

your speakers by cleaning them with a

vacuum cleaner. Use a feather duster or a

soft cloth instead.

Service and Repair

If your system is not performing as it should,

take it to your local RadioShack store for

assistance. To locate your nearest

RadioShack, use the store locator feature on

RadioShack's website

(www.radioshack.com), or call 1-800-The

Shack (843-7422) and follow the menu

options. Modifying or tampering with the

system's internal components can cause a

malfunction and might invalidate its

warranty and void your FCC authorization

to operate it.

FCC Declaration of

Conformity

This device complies with Part 15 of the

FCC Rules. Operation is subject to the

following two conditions: (1) this device

may not cause harmful interference, and (2)

this device must accept any interference

received, including interference that may

cause undesired operation.

The FCC Wants You to Know

This equipment has been tested and found

to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide

reasonable protection against harmful

interference in a residential installation. This

equipment generates, uses and can radiate

radio frequency energy and, if not installed

and used in accordance with the

instructions, may cause harmful interference

to radio communications. However, there is

no guarantee that interference will not occur

in a particular installation. If this equipment

does cause harmful interference to radio or

television reception, which can be

determined by turning the equipment off

and on, the user is encouraged to try to

correct the interference by one or more of

the following measures:

Product: Portable 900 MHz

Wireless Speaker

System

Model: 40-5029

Responsible

Party:

RadioShack

100 Throckmorton

Fort Worth, TX

76102

Phone: 817-415-3200

• Reorient or relocate the receiving

antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet

on a circuit different from that to which

the receiver is connected.

• Consult your local RadioShack store or

an experienced radio/TV technician for

help.

• If you cannot eliminate the interference,

the FCC requires that you stop using

your system.

Changes or modifications not expressly

approved by RadioShack may cause

interference and void the user’s authority to

operate the equipment.

Troubleshooting

We do not expect you to have problems with your speaker system; however, if you do have

problems, try these troubleshooting tips.

Problem Solution

No sound. Be sure the speakers are turned on.

Replace the speakers’ batteries.

Be sure the AC adapter is plugged in and

has power.

Be sure all cables are securely connected.

Be sure the audio source is turned on and

turned to an active channel.

Adjust the speakers’ volume control.

Distorted audio. Be sure the speakers and transmitter are set

to the same channel.

If you connected the transmitter to an audio

source’s headphone jack, reduce the audio

source’s volume.

Change the position of the transmitter.

The speakers are placed beyond the

transmitter’s effective range (approximately

300 feet). Move the speakers closer to the

transmitter.

Other 900 MHz transmissions are being

picked up by the speaker’s receiver

(possibly from a 900 MHz cordless

telephone). Change the transmitter’s and

the speaker’s frequency channel.

The speaker’s batteries are low. Replace the

batteries.

Inhaltsverzeichnis

Andere Radio Shack Sprecher Handbücher

Radio Shack

Radio Shack 21-549 Bedienungsanleitung

Radio Shack

Radio Shack 40-210 Bedienungsanleitung

Radio Shack

Radio Shack Amplified Stereo Computer Speakers Bedienungsanleitung

Radio Shack

Radio Shack 40-4093 Bedienungsanleitung

Radio Shack

Radio Shack 21-130 Bedienungsanleitung

Radio Shack

Radio Shack Mini Amplifier/Speaker Bedienungsanleitung

Radio Shack

Radio Shack STS 800 Bedienungsanleitung

Radio Shack

Radio Shack 4000466 Bedienungsanleitung

Radio Shack

Radio Shack 2100131 Bedienungsanleitung

Radio Shack

Radio Shack 40-1426 Bedienungsanleitung

Radio Shack

Radio Shack PA-115 Bedienungsanleitung

Radio Shack

Radio Shack 32-1245 Bedienungsanleitung

Radio Shack

Radio Shack 3 1/2-Inch Super Horn Tweeter Bedienungsanleitung

Radio Shack

Radio Shack 40-4091 Bedienungsanleitung

Radio Shack

Radio Shack PRO LX7 Bedienungsanleitung

Radio Shack

Radio Shack 40-4094 Bedienungsanleitung

Radio Shack

Radio Shack 40-4092 Bedienungsanleitung

Radio Shack

Radio Shack PA-110 Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung