RadioLink T8fb Bedienungsanleitung

RadioLink Electronic Ltd

www.radiolink.com

T8FB

(FHSS)

INSTRUCTION MANUAL

Compatible with Helicopter/Fixed Wing/Multicopter/Car/Boat

CE FCC

* Please be kindly noted that this manual will be updated regularly and please visit Radiolink official

website to download the latest version.

RadioLink Electronic Ltd

www.radiolink.com

Thank you for purchasing Radiolink 2.4 GHz remote control system T8FB .

To fully enjoy the benefits of this product and ensure safety, please read the manual carefully

and set up the device as instructed steps.

If any problems found during the operation process, either way listed below can be used as

online tech support.

1. Send mails to after_service@radioLink.com.cn or after_service1@radioLink.com.cn and we will

answer your question at the earliest.

2. PM us on our Facebook page or leave comments on our Youtube page

3. If the product is purchased from RadioLink AliExpress Global or Amazon U.S , you can contact

after-sales service directly.

4. If the product is purchased from the local distributor, you can also ask them for support and

repair as prefer.

All manuals and firmwares are available on RadioLink official website www.radiolink.com and more

tutorials are uploaded. Or follow our Facebook and Youtube homepage to stay tuned with our latest

news.

SAFETY PRECAUTIONS

Never operate your model during adverse weather conditions. Poor visibility can cause

disorientation and loss of control of your model.

Never use this product in a crowd and illegal area.

Always ensure the trim levers at 0 and battery properly charged before connecting the receiver.

Always check all servos and their connections prior to each run.

Always be sure about turning off the receiver before the transmitter.

WARNING

This product is not a toy and is NOT suitable for children under the age of 18. Adults should

keep the product out of the reach of children and exercise caution when operating this product in

the presence of children.

Water or moisture may enter the transmitter inside through gaps in the antenna or joystick and

cause model instability, even out of control. If running in the wet weather(such as game) is inevitable,

always use plastic bags or waterproof cloth to cover the transmitter.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions:

1This device may not cause harmful interference, and

2This device must accept any interference received, including interference that may cause

undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could

void the user's authority to operate the equipment.

RadioLink Electronic Ltd

www.radiolink.com

CONTENTS

Part 1 INTRODUCTION OF T8FB SYSTEM................................................................................................................... 3

1.1 T8FB Introduction................................................................................................................................................ 3

1.2 Guidelines to mount the servos, receiver and battery ............................................................................4

1.3 Compatible Receivers : R8EF and R8FM ......................................................................................................5

1.4 Transmitter Calibration......................................................................................................................................8

Part 2 Firmware Upgrade.................................................................................................................................................9

2.1 Firmware Introduction.......................................................................................................................................9

2.2 Upgrade Steps..................................................................................................................................................... 9

PART 3 T8FB Parameters Setup via Android Smart-phone APP.........................................................................12

3.1 Configuration.....................................................................................................................................................12

3.2 APP Installation................................................................................................................................................. 12

3.3 Connection Steps..............................................................................................................................................13

3.4 The Functions Introduction............................................................................................................................14

3.4.1 Setting Buttons Introduction................................................................................................................15

3.4.2 Four Interface Introduction...................................................................................................................16

3.5 FAQ....................................................................................................................................................................... 21

Part 4 T8FB Parameters Setup via Computer.........................................................................................................23

4.1 Parameter Configuration Software Setup Steps .................................................................................. 23

4.2 Software Description......................................................................................................................................24

4.2.1 BASIC MENU...........................................................................................................................................25

4.2.2 ADVACNE MENU.................................................................................................................................. 26

RadioLink Electronic Ltd

www.radiolink.com

Part 1 INTRODUCTION OF T8FB SYSTEM

1.1 T8FB Introduction

1) One two-way switch, one three-way switch, two VR switches, four trimmers, two sticks.

2) The picture below is mode1, SwB is default to control CH5, VrB is default to control CH6, SwA

is default to control CH7 and VrA is default to control CH8.

3) Universal JST battery connector supports multiple batteries, include 4pcs AA batteries or 2S to

4S LiPo battery.

4) Defaulted low battery alarm voltage can automatically match 2S and 3S LiPo battery or 4pcs

AA batteries, can setting in the T8FB configure software.

3S LiPo battery: default low voltage alarm to 11.0V automatically after detection, you can setup

low battery voltage alarm from 10.0V to 12.5V.

2S LiPo battery: default low voltage alarm to 7.3V automatically after detection, you can setup low

battery voltage alarm from 7.0V to 8.9V.

4 pcs AA Ni-MH battery: default low voltage alarm to 5.0V automatically after detection, you can

setup low battery voltage alarm from 4.0V to 6.4V.

（MODE 1）

RadioLink Electronic Ltd

www.radiolink.com

1.2 Guidelines to mount the servos, receiver and battery

•Make certain the alignment tab on the battery, switch and servo connectors is orient correctly

and ‘key’ into the corresponding notch in the receiver or connectors before plugging them

in.When unplugging connectors, never pull on the wires. Always pull on the plastic connector instead.

•Receiver’s Antenna: In generally receiver’s antenna is longer than remote control,don’t

break or retract it,otherwise shorten the control distance.The antenna must be kept away from

conductive materials,such as metal. Please make distance test before flying.

• If your aileron servos are too far away to plug into the receiver,use an aileron extension cord to

extend the length. Avoid plugging multiple extensions together to obtain your desired length. If the

distance is greater than 50cm or high current draw servos are being used, use heavy servo extensions.

•Receiver Vibration and Waterproofing: the receiver contains precision electronic part.Be sure

to avoid vibration,shock,and temperature extremes. For protection, wrap the receiver in foam rubber

or other vibration-absorbing materials. It is also a good idea to waterproof the receiver by placing it

in a plastic bag and securing the open end of the bag with a rubber band before wrapping it with

foam rubber. If you accidentally get moisture or fuel inside the receiver,you may experience

intermittent operation or a crash. If in doubt, please contact Radiolink after-sales or distributors for

service.

•Always mount the servos with the supplied rubber grommets. Don’t over tighten the screws.

No part of the servo casing should contact the mounting rails, servo tray or any part of structure.

RadioLink Electronic Ltd

www.radiolink.com

Otherwise vibration will be transmitted to the servo causing damage of servo. Note the small

numbers (1,2,3,4) molded into each arm on the servo arms. The number indicate how many degrees

each arm is ‘off’ from 90 degrees to correct for minute manufacturing deviations from servo to

servo.

To center the servos, connect them to receiver and turn on the transmitter and receiver. Center the

trims on the transmitter, then find the arm that will be perpendicular to the push rod when placed on

the servo.

After the servos are installed, operate each servo over its full travel and check that the push rods and

servo arms don ’ t bind or contact each other. Also make sure the controls do not require excess

force to operate. If there is an objectionable buzzing sound coming from a servo, there is probably

too much resistance in the control. Find and correct the problem. Even there is no servo damage,

excess battery drain will result.

•Use the mouthing plate from the receiver on/off switch as a template for the cutout and screw holes,

mount the switch on the side of the fuselage opposite the engine exhaust, and where it won’t be

inadvertently turned on or off during handling or storage. Be certain the switch moves without

restriction and ‘ snaps ’ from ON to OFF, and that the cutout allows full motion of the switch in

both directions.

•When install the switch harness to the helicopter, please use the switch cover. Generally sandwich

the frame between the switch and switch cover and securely tighten the screws. Different models

might require different installations. If so, please follow the model’s instruction manual.

• To prevent the servo lead wires from being broken by vibration during flight, provide a slight

amount of slack or extra so that the wire sticks out slightly and fasten it at suitable points. In addition,

periodically check the wire during daily maintenance.

1.3 Compatible Receivers : R8EF and R8FM

Radiolink T8FB is sells with 2.4G 8 channels receiver R8EF. R8EF is support S-BUS , PPM and PWM

signal working at the same time.

RadioLink Electronic Ltd

www.radiolink.com

Specification:

1) Channels: 8 channels

2) Working voltage: 4.8-10V

3) Working current: 30mA（input voltage:

5V）

4) Size: 48.5*21*11mm

5) Weight: 7g

6) 2048 section precision, 0.5us per

section, servo anti-shake rudder.

7) Control distance: about 500m ground

and 1000m air, actually control distance depends on the environment.

Two signal working mode:

(1) PWM signal output working mode：

Red LED indicates PWM signal output, 8 channels totally.

(2) S-BUS&PPM signal output working mode:

Blue/purple LED indicates SBUS&PPM signal output, 8 channels totally. When at this mode, SBUS and

PWM signal are working synchronously. CH1 output S-BUS signal, CH2 output PPM signal, CH3 to

CH8 output PWM signal at the same time.

RadioLink Electronic Ltd

www.radiolink.com

S-BUS&PPM and PWM signal change:

Quickly press the ID SET switch two times within 1 second, the signal will be changed from PWM to

S-BUS&PPM. The red LED indicates the PWM mode while blue/purple LED indicates S-BUS&PPM

mode.

MINI Receiver R8FM

T8FB is also compatible with 2.4G 8 channels supper mini receiver R8FM, which support S-BUS and

PPM signal working at the same time, supper mini size, is designed for racing drone.

Specification:

1) Channels: 8 channels

2) Working voltage: 4.8-6V

3) Working current: 30mA（input voltage: 5V）

4) Size: 16.0*21.5*1.0mm

5) Weight: 2.5g

6) 2048 section precision, 0.5us per section,

servo anti-shake rudder.

7) Control distance: about 500m ground and

1000m air, actually control distance depends on the environment.

S-BUS&PPM signal change:

Quickly press the ID SET switch two times within 1 second, the signal will be changed from PWM to

S-BUS&PPM. The red LED indicates the PWM mode while blue/purple LED indicates S-BUS&PPM

mode.

RadioLink Electronic Ltd

www.radiolink.com

How to bind receiver with transmitter:

1. Put the transmitter and the receiver close to each other within 50 centimeters.

2. Power on T8FB and receiver R8EF(or R8FM). The RED LED will start flashing slowly.

3. Turn on T8FB and it will automatically bind with the closest receiver.

4. There is a black binding button (ID SET) on the side of receiver. Press the button for more than 1

second and release, the RED LED will flash quickly, meaning binding process is ongoing.

5. When the RED LED stops flashing and is always on , binding is complete.

6. Make sure servos connected with the receiver can be operated by the transmitter.

Note of receiver usage：

1. Keep antennas as straight as possible, or the effective control range will reduce.

2. Big models may contain metal parts that influence signal emission. In this case. antennas should be

positioned at both sides of the model to ensure the best signal status in all circumstances.

3. Antennas should be kept away from metal conductor and carbon fiber at least half inch away and

no over bending.

4. Keep antennas away from motor, ESC or other possible interference sources.

5. Sponge or foam material is advised to use to prevent vibration when installing receiver.

6. Receiver contains some electronic components of high-precision. Be careful to avoid strong

vibration and high temperature.

7. Special vibration-proof material for R/C like foam or rubber cloth is used to pack to protect

receiver. Keeping the receiver in a well sealed plastic bag can avoid humidity and dust, which would

possibly make the receiver out of control.

1.4 Transmitter Calibration

Press rudder trimmer left and turn on transmitter at the same time, red and green LED flashing.

1) End point calibration：

Push two sticks from the highest position to the lowest position, and then put sticks to the center

position. (P1)

（P1）

2) Center position calibration:

Put stick to the center position, press rudder trimmer right, and then red and green LED always on

means sticks calibrate successful.

RadioLink Electronic Ltd

www.radiolink.com

Part 2 Firmware Upgrade

Connect T8FB to a computer with an android USB cable, then setup parameters as you need.

Upgrade firmware by a USB cable helps T8FB always keeps the most advanced system and program.

The USB data backup copy function of T8FB helps save and copy parameter settings easily.

2.1 Firmware Introduction

The latest firmware is T8FB_FHSS_V201_a77b_20170609_33bit.

We will upgrade firmware according to T8FB users, new firmware will not upgrade in this manual, you

can download it from our website: www.radiolink.com

2.2 Upgrade Steps

(1) Download the divers that T8FB upgrade need from our website:

http://radiolink.com.cn/doce/t8fb-upgrade-info.html

(2) Open file“T8FB”.

(3) Choose COM, and click “Connect” and then turn on T8FB in 1 second.

Andere Handbücher für t8fb

Inhaltsverzeichnis

Andere RadioLink Fernbedienung Handbücher

RadioLink

RadioLink RC4GS Bedienungsanleitung

RadioLink

RadioLink AT9 Bedienungsanleitung

RadioLink

RadioLink t8fb Bedienungsanleitung

RadioLink

RadioLink Ei411H Bedienungsanleitung

RadioLink

RadioLink AT10II Bedienungsanleitung

RadioLink

RadioLink t8fb Bedienungsanleitung

RadioLink

RadioLink T8S Bedienungsanleitung

RadioLink

RadioLink T8S Bedienungsanleitung

RadioLink

RadioLink AT10II Bedienungsanleitung

RadioLink

RadioLink RC6GS V3 Bedienungsanleitung

RadioLink

RadioLink RC4GS V3 Bedienungsanleitung

RadioLink

RadioLink Ei 411 Bedienungsanleitung

RadioLink

RadioLink t8fb Bedienungsanleitung

RadioLink

RadioLink t8fb Bedienungsanleitung

RadioLink

RadioLink T6EAP Bedienungsanleitung

RadioLink

RadioLink T8S Bedienungsanleitung

RadioLink

RadioLink T8S Bedienungsanleitung

RadioLink

RadioLink RC6GS V2 Bedienungsanleitung

RadioLink

RadioLink RC4GS V2 Bedienungsanleitung

RadioLink

RadioLink RC4GS V3 Bedienungsanleitung

RadioLink

RadioLink RL036T-001A Bedienungsanleitung

RadioLink

RadioLink AT10 Bedienungsanleitung

RadioLink

RadioLink RC8X Bedienungsanleitung

RadioLink

RadioLink AT10II Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung