Radionics D9210B Technisches Datenblatt

D9210B Access Control Interface Module

Operation and Installation Manual

www.PDF-Zoo.com

firealarmresources.com

Page 2

Notices

About This Manual

This manual assumes that you have basic security system installation skills such

as measuring voltages, stripping wire, making proper wire connections, and

checking phone lines. It also assumes you are familiar with the proper

installation of Radionics Control/Communicator panels and the related

programming tasks.

The material and instructions in this manual have been carefully checked for

accuracy and are presumed to be reliable. However, Radionics, Inc. assumes no

responsibility for inaccuracies and reserves the right to modify and revise this

manual without notice.

It is our goal at Radionics to always supply accurate and reliable documentation.

If a discrepancy is found in this documentation, please mail a photocopy of the

corrected material to:

Radionics, Inc.

c/o Technical Writing Department

130 Perinton Parkway

Fairport, NY 14450

FCC Notice

This equipment generates, uses and can radiate radio frequency energy. If not

installed in accordance with the manufacturer’s instructions, it may cause

interference to radio communications. It has been tested and found to comply

with the specifications in Subpart J of Part 15 of FCC Rules for Class B

Computing Devices.

If this equipment causes interference to radio or television reception –– which

can be determined by turning the equipment on and off –– the installer is

encouraged to correct the interference by one or more of the following measures:

1) Reorient the antenna of the radio/television, 2) Connect the AC transformer to

a different outlet so the control panel and radio/television are on different branch

circuits, 3) Relocate the control panel with respect to the radio/television.

If necessary, the installer should consult an experienced radio/television

technician for additional suggestions, or send for the “Interference Handbook”

prepared by the Federal Communications Commission. This booklet is available

from the U.S. Government Printing Office, Washington DC 20402, stock no. 004-

000-00450-7.

Regulatory Listings

UL 294 UL 1076 UL 609 FCC 15B

UL 365 UL 1610 UL 864 CSFM

www.PDF-Zoo.com

firealarmresources.com

Page 3

Table of Contents

Notices................................................................................................................................................................2

About This Manual ..........................................................................................................................................2

FCC Notice......................................................................................................................................................2

Regulatory Listings..........................................................................................................................................2

Table of Contents ..............................................................................................................................................3

Tables and Figures............................................................................................................................................ 4

Introduction........................................................................................................................................................5

The D9210B Access Control Interface............................................................................................................5

Materials Included ...........................................................................................................................................6

Ordered Separately.........................................................................................................................................6

Listings and Approval Information...................................................................................................................6

Installation..........................................................................................................................................................7

Before You Begin ............................................................................................................................................7

Step 1: Mounting the Enclosure and Installing the D9210B............................................................................7

Step 2: Pulling and Marking the Wires............................................................................................................8

Step 3: Mounting ...........................................................................................................................................10

Step 4: Door Contact (Onboard) Point, Terminals 9 and 10.........................................................................10

Step 5: Door Lock, Terminals 2, 3 and 4.......................................................................................................11

Step 6: Request to Enter (RTE), Terminals 11 and 12 .................................................................................12

Step 7: Request to Exit (REX), Terminals 13 and 12....................................................................................12

Step 8: Enclosure Tamper Switch, Terminals 8 and 9..................................................................................12

Step 9: Connecting the Card Reader, Terminals 12, 14, 15, 16, 17, and 18 ................................................13

Step 10: Setting the Dipswitch and Tagging the Unit....................................................................................14

Step 11 Connecting Power and SDI, Terminals 1, 5, 6, 7, and 9..................................................................15

Step 12: Programming and Activating the D9210B.......................................................................................16

Step 13: Testing the D9210B........................................................................................................................16

Troubleshooting ..............................................................................................................................................17

Detailed System Description .......................................................................................................................... 18

Operational Primer........................................................................................................................................18

Basic Features ..............................................................................................................................................21

Displays and Reports ....................................................................................................................................21

Door Release Application ...............................................................................................................................22

D9210B Terminal Quick Reference and Electrical Specifications ..............................................................23

www.PDF-Zoo.com

firealarmresources.com

Page 4

Tables and Figures

TABLE 1. D9210B DIAGNOSTIC AND STATUS LEDS......................................................................................5

TABLE 2. TYPICAL WIRE PLANNING CHART FOR THE D9210B....................................................................8

TABLE 3. UL LISTED COMPATIBLE READERS FOR THE D9210B...............................................................13

TABLE 4. D9210B DIP SWITCH SETTINGS ....................................................................................................14

TABLE 5. LED TROUBLESHOOTING GUIDE..................................................................................................17

TABLE 6. TERMINAL QUICK REFERENCE GUIDE AND ELECTRICAL SPECIFICATIONS..........................23

FIGURE 1. D9210B ACCESS CONTROL INTERFACE MODULE .....................................................................5

FIGURE 2. WIRING DIAGRAM FOR TYPICAL D9210B INSTALLATION..........................................................9

FIGURE 3. RELAY INSTALLATION ..................................................................................................................11

FIGURE 4. D9210B DIPSWITCH WITH FACTORY DEFAULT SETTINGS.....................................................14

FIGURE 5. POWER SUPPLY AND SDI CONNECTIONS.................................................................................15

FIGURE 6. D9210B DOOR RELEASE APPLICATION CONNECTIONS..........................................................22

www.PDF-Zoo.com

firealarmresources.com

Page 5

Introduction

The D9210B Access Control Interface

PWR+

SDIB

SDIA

COM

T+

ZN+

ZNCOM

LCKN/C

LCKCOM

LCKN/O

REX

COM

RTE

DATA1

BUZZER

LED

DATA0

+5.20V

READER

OPER

MON

READER

D9210B

Terminal

Blocks

Diagnosticand

StatusLEDs

EPROM

DIPSwitch

Relay

Figure 1. D9210B Access Control Interface Module

Terminal Blocks. The D9210B comes with three banks of terminal blocks for

connecting the D9210B to its power source, the panel and associated readers

and relays.

Relay. A removable (model D136) relay provides a dry contact single pull, double

throw output.

Dipswitch. The D9210B dipswitch has six on-off switch settings. Setting these

switches allows each unique D9210B to be programmed for a specific address.

EPROM. The D9210B is controlled by a programmable read-only memory

microprocessor.

Diagnostic and Status LEDs. The D9210B has a series of light emitting diodes

(LEDs) for identifying operational and diagnostic states. These are listed below.

LED Action State

Operational Monitor (Green) LED blinks on and off System is operational

LED is on or off (solid) System is off or not operational

D0 Reader (Green) LED rapidly blinking Card data executing

LED is off No card data is being received

D1 Reader (Yellow) LED rapidly blinking Card data executing

LED is off No card data is being sent

Table 1. D9210B Diagnostic and Status LEDs

www.PDF-Zoo.com

firealarmresources.com

Page 6

Materials Included

Radionics ships the D9210B Access Control Interface module pre-assembled

from the factory with a power supply, in its own can, or as a unit less can. You

will receive the following parts with your package depending upon what model is

ordered, (see Ordered separately).

• D136 removable relay mounted on the board.

• Battery Leads (for the D9210BLC).

• 1K Ω1/2 watt end of line resistor.

• Literature Pack containing: D9210B Operation and Installation Manual,

D9210 Program Entry Guide, ACCESS Program Record Sheet, and Power

Supply Installation Instructions.

• Hardware pack containing: three #6x3/8 self-tapping sheet metal screws to

secure the module on the mounting skirt or the enclosure. Two strain relief

cable ties.

Ordered Separately

The D9210B Door Controller can be used with the Radionics D7412 (supports 2

doors) or D9412 (supports 8 doors) Control/Communicator security panels and

associated control keypads and access control readers. Following are the

available options.

• D9210BLC: The D9210BLC (up to 4) can be installed in the same enclosure

as the control panel using the mounting screws and fasteners. Two additional

modules can be mounted using the D136 brackets. Radionics recommends

that you use a separate power supply for the D9210Bs to isolate them from

other SDI devices.

• D9210BC: The D9210BC is a complete unit mounted on a mounting skirt,

(D9201M) with a switchable 12/24 VDC (500-1500 mA) power supply, 24

VAC/40 VA fused transformer, and (1) D9210B. It can be installed with

another D9210BLC in a single D8103, D8109 or D8108A enclosure.

• D9210B: The D9210B is mounted in a 5(W)x8(L)x3(H) enclosure and can be

mounted as a standalone unit in the field.

• Compatible Readers: Readers are not shipped with the unit (see Table 3).

Listings and Approval Information

Underwriters Laboratories (UL). The D9210B, when used with the D7412 or

D9412 panels, is listed by UL for use as part of an Access Control System;

Local, Police-Connect, Central Station, or Proprietary Burglar Alarm System; and

a Commercial Fire Alarm System. In addition to the manual, refer to the

D7412/D9412 installation documentation regarding Burglar Alarm Grades and

Fire Alarm services supported. The D9210B is a Signaling Device Subassembly

also suitable as a Burglar Alarm Unit Accessory Subassembly and Access

Control Unit Subassembly.

Other Listings and Approvals. FCC 15B, CSFM (highrise)

www.PDF-Zoo.com

firealarmresources.com

Page 7

Installation

Before You Begin

Thank you for choosing our product. We have made an effort to identify the key

steps for installing the D9210B successfully. To ensure that your installation

goes smoothly, follow the installation steps in the order presented.

System Planning. Before proceeding, draw your system layout on a sheet of

graph paper. Also, review the architect and engineering drawings (if available).

This will help you set addresses, mark the units, and route/tag wires. The

drawing should include the Control Panel, the D9210B, the trip switches for

RTE/REX, doors, readers, control centers assigned to the same area as the

D9210Bs, and the wiring run.

Have the following documents handy as you read through this manual:

• D9210B Program Entry Guide (32207)

• ACCESS Program Record Sheet (32208)

• Control/Communicator Program Entry Guide and Program Record Sheet

• Security System Owner’s Manual (71-06633-000)

• Power Supply Installation Instructions

You should be familiar also with the operation of the D5200 programmer or the

Remote Account Manager (R.A.M.) remote programmer.

Step 1: Mounting the Enclosure and Installing the D9210B

Enclosure Placement. There is a 500’ maximum distance allowed between the

D9210B and Weigand card readers. There is a 5000’ maximum distance allowed

between the D9210B and the panel. Consider placing the enclosure where a

technician can gain easy access for troubleshooting the unit and where wiring

can be routed easily.

Preparing Knockouts. The D9210B requires six primary wire runs to be routed to

the enclosure (see Table 2). To identify the proper knockouts required,

determine from which direction the panel, reader, door contact, door strike and

the request to exit/enter wires will be coming. Run the necessary wiring

throughout the premises and pull the wires into the enclosure. Avoid splicing and

grouping wires together. Knock out the tabs for the wiring prior to mounting the

enclosure.

Mounting the Enclosure. When mounting the enclosure, place it against the wall

and use a “level tool” to ensure the unit is level. Align the enclosure mounting

holes with the vertical wood beams, usually 16” apart, to ensure a solid mount.

With a pen or pencil, make marks where the top mounting holes expose the

surface.

Set the enclosure down and insert the mounting screws where the marks exist

for the top left and right mounting holes. Leave a 1/4” gap between the wall and

screw head so the enclosure can be hung on the screws.

IMPORTANT! If vertical wood beams are not available, be sure to use the proper

screw anchors and hardware to mount the unit.

www.PDF-Zoo.com

firealarmresources.com

Page 8

If any of the knockouts require that wire be run behind the wall, mark the holes

and punch/drill them out prior to permanently installing the enclosure. After the

holes have been knocked out and the enclosure is level, use all five mounting

holes (three on the top and two on the bottom) to install the enclosure.

Step 2: Pulling and Marking the Wires

Running wire. Use Table 2 to estimate the wire bundle size for your knockouts

and where to mount the D9210B. Tag your wire runs to prevent confusion during

installation and troubleshooting. Figure 2 shows the wiring for a typical D9210B

installation.

Purpose Suggested

Wire Tag Approximate

Diameter Recommended

Wire Type Recommended

Color Code

Power/SDI data Tag A 1/4 “ 4/22 awg quad

(2500 feet)

4/18 awg quad

(5000 feet)

SDI: A (Green)

B (Yellow)

Pwr: + (Red)

- (Black)

RTE power/input* Tag B 1/4” 4/22 awg quad Green/Black

REX power/input* Tag C 1/4” 4/22 awg quad Yellow/Black

Strike power* Tag D 3/8” 2/16-18 awg zip Red

Door contact* Tag E 1/8” 2/22 awg twist White

Reader* Tag F 3/8” 6/22 awg

conductor

(500 feet)

12 VDC: Red

5 VDC: Orange

COM: Black

D1: White

D0: Green

LED: Brown

Buzzer: Yellow

Buzzer* Tag G 1/8” 2/22 awg twist +(Red), - (Blk)

Emergency Exit* Tag I 1/8” 2/18 awg twist Blue

Power Supply

Transformer Tag J 1/4” 2/18 awg zip Brown

* Be sure to multiply the wires by the number of D9210Bs in the enclosure.

Table 2. Typical Wire Planning Chart for the D9210B

www.PDF-Zoo.com

firealarmresources.com

Page 9

PWR+

SDIB

SDIA

COM

T+

ZN+

ZNCOM

LCKN/C

LCKCOM

LCKN/O

REX

COM

RTE

DATA1

BUZZER

LED

DATA0

+5.20V

READER

OPER

MON

READER

D9210

DOOR

DOORCONTACT

(NORMALE.O.L.

INCIRCUIT)

E.O.L.

RTE/REX

(NORMAL

OPEN)

(white)

(green)

(orange)

(brown)

12 VDC

BUZZER

12 VDCREADER

(+)

(-)

(yellow)

TAMPERSWITCH

(NORMALOPEN)

(black)

12 VDC

DOOR

STRIKE

Somejurisdictionswill not

allowthe useofEmergencyEgress as

yoursolemeansofescape.Ifthis

featureisused,itstill maybe necessary

toprovide listed panichardware.

Consultyourlocalauthorityhaving

jurisdiction (AHJ)priortoinstallation.

CAUTION

DONOTpowerthe

D9210 Module

with24 VDC.

CAUTION

Strike and

D9210

NOTE:A24VDC powersupplymaybe used forthe door

strikeifneccessary.

Figure 2. Wiring Diagram for Typical D9210B Installation

www.PDF-Zoo.com

firealarmresources.com

Page 10

Step 3: Mounting

CAUTION Do not install or replace a D9210B while it is connected to live power

circuits. The D9210B should be powered down until it is ready to be tested.

D9210BLC

1. Mount the D8103, D8109 or D8108A enclosure on a flat service.

2. Install another D9210LC to the mounting skirt (optional) prior to step 3.

3. Hang the mounting skirt in the enclosure by aligning the rectangular tabs of

the enclosure with the rectangular knockouts on the mounting skirt.

4. Insert the #6x3/8” screw on the bottom tab of the mounting skirt and tighten

1/4 turn to seat it. This completes the mounting of the skirt in the enclosure.

D9210B

1. Remove the cover of the D9210B by loosening the two cover screws.

2. Remove the required knockouts prior to replacing the cover.

3. Mark the holes provided for mounting the bottom half of the unit to a wall or

ceiling.

4. Screw the provided screws in to the marked service and allow a 1/4” gap

between the surface and bottom of the screw.

5. Hang the unit and secure the screws. Replace the cover and cover screws.

D9210BLC

1. The unit can be installed in a D8103, D8109 or D8108A enclosure by

matching the three plastic mounting anchors to the three hole foot prints

provided around the sides of the enclosure (4).

2. The unit can be added to a D9210BC by matching the three plastic mount

anchors to the available three hole foot prints below the factory installed

D9210B.

3. To secure the unit, use the three #8-3/4” screws provided.

Step 4: Door Contact (Onboard) Point, Terminals 9 and 10

Description. The D9210B monitors the sensor loop between the input terminal

10 and the common terminal 9 for normal, shorted, or open conditions. This loop

is provided for a door contact. The door contact can be programmed as a

perimeter, interior, or 24 hour burglar alarm point.

See the D9210B Program Entry Guide (32207) for assigning a point to the door

controller and the panel Program Entry Guide for the point types.

Point Sensor Loop. Install a 1k Ωresistor at the door contact, not at the

terminal of the input. This will provide supervision against grounds on the loop.

You can connect only one contact, that being the door, to this input.

www.PDF-Zoo.com

firealarmresources.com

Andere Handbücher für D9210B

Inhaltsverzeichnis

Andere Radionics Aufnahmegeräte Handbücher

Radionics

Radionics D9210B Fehlerbehebungshandbuch

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch