RAIS Q-Tee 2 Stücklistenhandbuch

ENGLISH RAIS - manual for Rais Q-Tee 2

INSTRUCTIONS FOR INSTALLATION,

USE AND MAINTENANCE

RAIS Q-Tee 2

IMPORTANT INFORMATION

On first lig ting t e stove you must be careful not to touc t e painted

surfaces and it is MOST IMPORTANT t at t e door is kept slig tly ‘ajar’ in

order for t e door seal and sealant to cure.

T is will prevent t e door seal sticking to t e painted body and becoming

damaged.

ENGLISH RAIS - manual for Rais Q-Tee 2

Please note t at it is a legal requirement under England and Wales Building

Regulations t at t e installation of t e stove is eit er carried out under Local

Aut ority Building Control approval or is installed by a Competent Person

registered wit a Government approved Competent Persons Sc eme. HETAS Ltd

operate suc a Sc eme and a listing of t eir Registered Competent Persons can

be found on t eir website at www. etas.co.uk.

CO Alarms:-

Building regulations require t at w en ever a new or replacement fixed solid fuel

or wood/biomass appliance is installed in a dwelling a carbon monoxide alarm

must be fitted in t e same room as t e appliance. Furt er guidance on t e

installation of t e carbon monoxide alarm is available in BS EN 50292:2002 and

from t e alarm manufacturer’s instructions.

Provision of an alarm must not be considered a substitute for eit er installing t e

appliance correctly or ensuring regular servicing and maintenance of t e

appliance and c imney system.

HEALTH AND SAFETY PRECAUTIONS

Special care must be taken when installing the stove such that the re uirements of the

Health and Safety at Work Act are met.

Handling

Ade uate facilities must be available for loading, unloading and site handling.

Fire Cement

Some types of fire cement are caustic and should not be allowed to come into contact

with the skin. In case of contact wash immediately with plenty of water.

Asbestos

This stove contains no asbestos. If there is a possibility of disturbing any asbestos in

the course of installation then please seek specialist guidance and use appropriate

protective e uipment.

Metal Parts

When installing or servicing this stove care should be taken to avoid the possibility of

personal injury.

These instructions together with those in the instruction booklet cover

the basic principles to ensure the satisfactory installation of the stove,

although detail may need slight modification to suit particular local site

conditions.

In all cases t e installation must comply wit current Building Regulations,

Local Aut ority Byelaws and ot er specifications or regulations as t ey affect

t e installation of t e stove.

It s ould be noted t at t e Building Regulations requirements may be met by

adopting t e relevant recommendations given in Britis Standards BS 8303,

BS EN 15287-1:2007 as an alternative means to ac ieve an equivalent level of

performance to t at obtained following t e guidance given in Approved

Document J.

ENGLISH RAIS - manual for Rais Q-Tee 2

STOVE PERFORMANCE

In the UK the stove has been approved by HETAS Ltd as an intermittent operating

appliance for burning wood logs only.

PREPARATORY WORK AND SAFETY CHECKS

IMPORTANT WARNING

This stove must not be installed into a chimney that serves any other heating appliance.

There must not be an extractor fan fitted in the same room as the stove as this can cause

the stove to emit fumes into the room.

C imney

In order for the stove to perform satisfactorily the chimney height must be sufficient to

ensure an ade uate draught of approximately 15 Pa so as to clear the products of

combustion and prevent smoke problems into the room.

NOTE: A chimney height of not less than 4.5 metres measured vertically from the outlet of

the stove to the top of the chimney should be satisfactory. Alternatively the calculation

procedure given in EN 13384-1 may be used as the basis for deciding whether a particular

chimney design will provide sufficient draught.

Please Note, this appliance has been tested by the manufacturers and works on a 3m

straight flue.

The outlet from the chimney should be above the roof of the building in accordance with

the provisions of Building Regulations Approved Document J.

If installation is into an existing chimney then it must be sound and have no cracks or other

faults which might allow fumes into the house. Older properties, especially, may have

chimney faults or the cross section may be too large i.e. more than 230 mm x 230 mm.

Remedial action should be taken, if re uired, seeking expert advice, if necessary. If it is

found necessary to line the chimney then a flue liner suitable for solid fuel must be used in

accordance with Building Regulations Approved Document J.

Any existing chimney must be clear of obstruction and have been swept clean immediately

before installation of the stove. If the stove is fitted in place of an open fire then the

chimney should be swept one month after installation to clear any soot falls which may

have occurred due to the difference in combustion between the stove and the open fire.

If there is no existing chimney then either a prefabricated block chimney in accordance

with Building Regulations Approved Document J or a twin walled insulated stainless steel

flue to BS 1856-1 can be used. These chimneys must be fitted in accordance with the

manufacturer’s instructions and Building Regulations.

ENGLISH RAIS - manual for Rais Q-Tee 2

STOVE PERFORMANCE

In the UK the stove has been approved by HETAS Ltd as an intermittent operating

appliance for burning wood logs only.

PREPARATORY WORK AND SAFETY CHECKS

IMPORTANT WARNING

This stove must not be installed into a chimney that serves any other heating appliance.

There must not be an extractor fan fitted in the same room as the stove as this can cause

the stove to emit fumes into the room.

C imney

In order for the stove to perform satisfactorily the chimney height must be sufficient to

ensure an ade uate draught of approximately 15 Pa so as to clear the products of

combustion and prevent smoke problems into the room.

NOTE: A chimney height of not less than 4.5 metres measured vertically from the outlet of

the stove to the top of the chimney should be satisfactory. Alternatively the calculation

procedure given in EN 13384-1 may be used as the basis for deciding whether a particular

chimney design will provide sufficient draught.

Please Note, this appliance has been tested by the manufacturers and works on a 3m

straight flue.

The outlet from the chimney should be above the roof of the building in accordance with

the provisions of Building Regulations Approved Document J.

If installation is into an existing chimney then it must be sound and have no cracks or other

faults which might allow fumes into the house. Older properties, especially, may have

chimney faults or the cross section may be too large i.e. more than 230 mm x 230 mm.

Remedial action should be taken, if re uired, seeking expert advice, if necessary. If it is

found necessary to line the chimney then a flue liner suitable for solid fuel must be used in

accordance with Building Regulations Approved Document J.

Any existing chimney must be clear of obstruction and have been swept clean immediately

before installation of the stove. If the stove is fitted in place of an open fire then the

chimney should be swept one month after installation to clear any soot falls which may

have occurred due to the difference in combustion between the stove and the open fire.

If there is no existing chimney then either a prefabricated block chimney in accordance

with Building Regulations Approved Document J or a twin walled insulated stainless steel

flue to BS 1856-1 can be used. These chimneys must be fitted in accordance with the

manufacturer’s instructions and Building Regulations.

ENGLISH RAIS - manual for Rais Q-Tee 2

Combustion air supply

In order for the stove to perform efficiently and safely there should be an ade uate air

supply into the room in which the stove is installed to provide combustion air. This is

particularly necessary if the room is double-glazed or a flue draught stabiliser is

operating in the same room as the appliance. It may be necessary to increase the air

vent size in property with low air permeability ( < 5.0 m

/(h.m

The provision of air supply to the stove must be in accordance with current Building

Regulations Approved Document J. An opening window is not appropriate for this

purpose.

IMPORTANT NOTE: If applicable and the appliance is being fitted within an existing

fireplace recess, specialist advice should be sought before fitting any permanent

ventilation within this area.

Connection to c imney

Stoves may have a choice of either a rear or top flue gas connector that allows

connection to either a masonry chimney or a prefabricated factory made insulated metal

chimney in accordance with their instructions. In some cases it may be necessary to fit

an adaptor to increase the diameter of the flue to the minimum re uired 150 mm section

of the chimney or liner.

Electrical Services

The installation of any electrical services during the installation of this appliance must be

carried out by a registered competent electrician and in accordance with the

re uirements of the latest issue of BS 7671

Carbon Monoxide Alarm

A carbon monoxide alarm complying with BS EN 50292 must be fitted in the same room

as the appliance. It should be positioned on the ceiling at least 300mm from any wall or,

if it is located on a wall, as high up as possible (above any doors and windows) but not

within 150mm of the ceiling. The alarm should also be between 1m and 3m horizontally

from the appliance.

ENGLISH RAIS - manual for Rais Q-Tee 2

Installation

It is prohibited to carry out unauthorised alterations to the stove.

There must be plenty of fresh air in the room where the stove is being installed, in

order to ensure proper combustion. Note that any mechanical exhaust ventilation -

e.g. an extraction hood - may reduce the air supply. Any air grilles must be placed

in such a manner, that the air supply is not blocked.

Building Regulations Approved Document J gives specific guidance on the re uired

permanent ventilation into the room for combustion air of solid fuel appliances.

The floor structure must be able to carry the weight of the wood burning stove, as

well as the weight of a chimney, if necessary.

When you choose where to set up your RAIS wood burning stove, you should

consider the heat distribution to the other rooms. This will enable you to get the best

use out of your stove.

The stove should be set up at a safe distance from inflammable materials.

See the manufacturer's plate on the wood burning stove.

Commissioning and andover

Ensure loose parts are fitted in accordance with the instructions given in the

instruction booklet.

On completion of the installation allow a suitable period of time for any fire cement

and mortar to dry out, when a small fire may be lit and checked to ensure the

smoke and fumes are taken from the stove up the chimney and emitted safely to

atmosphere. Do not run at full output for at least 24 hours.

On completion of the installation and commissioning ensure that the operating

instructions for the stove are left with the customer. Ensure to advise the customer

on the correct use of the appliance with the fuels likely to be used on the stove and

warn them to use only the recommended fuels for the stove.

Advise the user what to do should smoke or fumes be emitted from the stove. The

customer should be warned to use a fireguard to BS 8423:2002 (Replaces BS

6539) in the presence of children, aged and/or infirm persons.

ENGLISH RAIS - manual for Rais Q-Tee 2

Revision :

Date : April 2013

HETAS SUPPLEMENT …………………………………………………….. 3

MANUFACTURERS PLATE ………………………………………………. 8

INTRODUCTION ………………………………………………………….. 10

WARRANTY …………………………………………………….………….. 10

SPECIFICATIONS ………………………………………………………….. 11

CONVECTION ………………………………………………………………. 13

INSTALLATION INSTRUCTIONS ………………………………….……… 12

CHIMNEY …………………………………………………….…………. 13

INSTALLATION ………………………………………………..……... 15

COMMISSIONING AND HANDOVER ……………………………… 11

CHANGING THE CHIMNEY CONNECTION …………………………….. 16

INSTALLATION DISTANCE TO COMBUSTIBLE WALL …………....... 17

INSTALLATION DISTANCE TO NON-COMBUSTIBLE WALL ……… 21

FOR THE INSTALLER ……………………………………………………… 22

OPERATING INSTRUCTIONS …………………………………………….. 22

FUEL …………………………………………………………………………... 22

DRYING AND STORAGE …………………………………………………… 23

REGULATION OF COMBUSTION AIR …………………………………… 23

ROOM VENTILATION AND STOVES …………………………………….. 24

USING THE WOOD BURNING STOVE …………………………………… 24

FIRST USAGE ………………………………………………………………… 26

LIGHTING AND FUELLING ………………………………………………… 27

CLEANING AND CARE …………………………………………………….. 30

CLEANING OF THE FLUE WAYS ………………………………………… 31

PROBLEM SOLVING ……………………………………………………….. 32

SPARE PARTS …………………………………………….…………………. 33

SPARE PART DIAGRAM …….………..……………………………………. 34

FITTING THE LOG STORE ……….………………………………………… 35

LOCK BLOCK FOR STEEL DOORS ………………………………………. 37

QUICK GUIDE …………………………………………………………………. 38

ENGLISH RAIS - manual for Rais Q-Tee 2

Andere Handbücher für Q-Tee 2

Inhaltsverzeichnis

Andere RAIS Kamin im Innenbereich Handbücher

RAIS

RAIS BIONIC FIRE Bedienungsanleitung

RAIS

RAIS Visio 160 F Bedienungsanleitung

RAIS

RAIS 500 Bedienungsanleitung

RAIS

RAIS attika NEXO 100 GAS Bedienungsanleitung

RAIS

RAIS Nexo 100 Bedienungsanleitung

RAIS

RAIS attika 600 MAX-1 Bedienungsanleitung

RAIS

RAIS 700 Technisches Handbuch

RAIS

RAIS Caro 90 Bedienungsanleitung

RAIS

RAIS TOPAS Montageanleitung

RAIS

RAIS VIVA L USA Bedienungsanleitung

RAIS

RAIS attika VISIO Series Bedienungsanleitung

RAIS

RAIS VISIO 100 F Bedienungsanleitung

RAIS

RAIS BIONIC FIRE Bedienungsanleitung

RAIS

RAIS Nexo 100 Bedienungsanleitung

RAIS

RAIS RAIS Q-BIC Bedienungsanleitung

RAIS

RAIS Visio 70 RD Bedienungsanleitung

RAIS

RAIS attika Visio 2 Bedienungsanleitung

RAIS

RAIS POLEO Technisches Handbuch

RAIS

RAIS SIRA Bedienungsanleitung

RAIS

RAIS INSERT 60 Bedienungsanleitung

RAIS

RAIS VISIO 3-1 NS Bedienungsanleitung

RAIS

RAIS POLEO 95 Bedienungsanleitung

RAIS

RAIS PILAR 13 H Stücklistenhandbuch

RAIS

RAIS Visio 90 F Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch