Raiscube A8R Bedienungsanleitung
USER MANUAL --Raiscube A8R 3D Printer
1
USER MANUAL --Raiscube A8R 3D Printer
2
PRODUCT WARRANTY
The RAISCUBE A8R 3D Printer is covered by a limited warranty.
OVERALL PROVISIONS
All information in this user manual (“Manual”) is subject to change at any time without notice and is
provided for convenience purposes only. Shenzhen Ruisizhizao Technology CO.,LTD and our
respective affiliates and suppliers (“Raiscube”) reserves the right to modify or revise this Manual in its
sole discretion and at any time and makes no commitment to provide any such changes, updates,
enhancements, or other additions to this Manual in a timely manner or at all. You agree to be bound by
any modifications and/or revisions. Contact the Raiscube Support Team for up-to-date information. In
order to protect Raiscube proprietary and confidential information and/or trade secrets, this document
may describe some aspects of Raiscube technology in generalized terms.
DISCLAIMERS
Raiscube does not warrant the accuracy or completeness of the information, products, or services
provided by or through this Manual and assumes no responsibility for any typographical, technical, or
other inaccuracies in this Manual, which is provided “as is” and without any express or implied
warranties of any kind, including warranties of merchantability, fitness for a particular purpose, or
non-infringement of intellectual property. In connection with your use of this Manual, Raiscube shall
not be liable to you for any damages whatsoever, be they direct, economic, commercial, special,
consequential, incidental, exemplary, or indirect damages, even if Raiscube has been advised of the
possibility of such damages, including without limitation, loss of business revenue or earnings, lost
data, or lost profits. Raiscube assumes no responsibility, nor will be liable, for any damages to, or any
viruses or malware that may infect, your computer, telecommunication equipment, or other property
caused by or arising from your downloading of any information or materials related to this Manual.
The foregoing exclusions do not apply to the extent prohibited by law; please refer to your local laws
for any such prohibitions. Raiscube makes no warranties to those defined as “consumers” in the
Magnuson-Moss Warranty-Federal Trade Commission Improvement Act.
INTELLECTUAL PROPERTY
Certain trademarks, trade names, service marks, and logos (the “Marks”) used in this Manual are
registered and unregistered trademarks, trade names, and service marks of Raiscube and its affiliates.
Nothing contained in this Manual grants or should be construed as granting, by implication, estoppel,
or otherwise, any license or right to use any Marks without the written permission of Raiscube. Any
unauthorized use of any information, materials, or Marks may violate copyright laws, trademark laws,
laws of privacy and publicity, and/or other laws and regulations. Other company and/or product names
mentioned herein may be trademarks of their respective companies.
© 2009-2016 Raiscube Industries, LLC. All rights reserved.
LEGAL NOTICE
USER MANUAL --Raiscube A8R 3D Printer
3
MANUFACTURER
Shenzhen Ruisizhizao Technology CO.,LTD
Floor 3, NO.18, Yaohui Industrial Park,
Dakan Industry Second Road,
Xili Street, Nanshan District,
Shenzhen, China. 518000.
RADIO AND TELEVISION INTERFERENCE
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the Federal Communications Commission (FCC) rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the machine.
Increase the separation between the equipment.
Connect the equipment to an outlet on a different circuit.
Any changes or modifications made to this equipment voids your authority to operate this equipment
under FCC Rules.
SAFETY AND COMPLIANCE
USER MANUAL --Raiscube A8R 3D Printer
4
Precautions
Warning: The printer can only be used with original power supply, or the product may be damaged, with a risk of
fire.
Warning: The RAISCUBE A8R generates high temperatures. To avoid burning, or model deformation, do not
touch the model, nozzle, or the platform by hand, or any other part of the body, while the printer is working or
immediately after it has finished printing.
Warning: There is a slight smell from ABS when it is being extruded. The smell is, however, not too unpleasant.
Operate in a well ventilated room but draught free. Draught can affect warping of ABS prints. When ABS is burnt
is releases toxic fumes.
Warning: Do not use ABS plastic or its printed parts near any kind of heat source, flames, fireworks, candles,
light bulbs, etc. ABS will catch fire and burn a thick black smoke.
Warning: Always have adult supervision when children are present. Please keep all small printed parts away
from young children, choking hazards! There are several safety issues, small tools, sharp tools and HOT
objects and most parts used in connection with the 3D Printer. Tie back long hair and loose clothing. Keep
fingers away from moving parts.
Warning: Tools and parts should be stored at a suitable height away from small children.
Caution: The socket outlet must be located near the equipment and must be easily accessible.
Caution: In case of emergency disconnect the RAISCUBE A8R from the wall socket.
Caution: The RAISCUBE A8R melts plastic during printing. Plastic odors are emitted during this operation.
Make sure to set up the RAISCUBE A8R in a well-ventilated area.
Warning: Do not leave the RAISCUBE A8R unattended during operation.
USER MANUAL --Raiscube A8R 3D Printer
5
Build Instruction of Raiscube A8R 3D Printer
Simply we can divide A8R into four segments – Frame, Build Platform, X&Z Motion, and circuit.
We are going to build it one by one in order. Therefore, four major steps to go completing it,
taking 1-3 hours from package to make it on in right way.
Ahead of building, get all parts including tools and screws out of box (Please refer to its
packing list for all parts), and check all if any damage exists, especially the wires and their
connectors. And Switch PSU to the correct position according to the voltage in your country.
E.g: 110V for US, 220V for UK.
STEP ONE, FRAME BUILD. Build Aluminum frame first and add remains to it in next three
steps.
First step, We need, left frame module, right frame module, Z Axis Stepper (R&L), Y Axis
Stepper, frame crossbeam, middle bottom plate, back plate, M3 Hex Key Wrench, and 18pcs
of M3*10 Socket Cap Screws. Please pick them from A8R package refer to Fig.b01.
Fig.b01
USER MANUAL --Raiscube A8R 3D Printer
6
STEP 1-1 Connect Z Axis Stepper (R&L) middle bottom plate, please differentiate Left
stepper from right stepper by the sideway hole as in Fig.b02, and we will get as in Fig.b03.
Here we we need 4 pcs of M3*10 Socket Cap Screws, 2pcs each side.
Fig.b02
Fig.b03
USER MANUAL --Raiscube A8R 3D Printer
7
STEP 1-2 Connect “Left Frame Module” & “Right Frame Module” & what done in Step 1-1
(Fig.b03) together by 4 pcs of M3*10 Socket Cap Screws, 2pcs each side.
Please check Fig.b04, and we got what as in Fig.b05.
Fig.b04 Fig.b05
STEP 1-3 Pick out “Back Plate” “Y Axis Stepper” and 2pcs of “M3*10 Socket Cap Screws”,
let “Y Axis Stepper” join “Back Plate” using the screws. Please refer to Fig.b06 and Fig.b07 for
this substep.
Fig.b06 Fig.b07
STEP 1-4: Add what done in step 1-3 to the main frame which was done in step 1-2, and
fasten them by 4pcs of M3*10 socket cap screws. From Fig.b08 to Fig.b09, it illustrates how is
this going.
Fig.b08 Fig.b09
USER MANUAL --Raiscube A8R 3D Printer
8
STEP 1-5: Add crossbeam. Find “Frame Crossbeam” in the package and also 4pcs of M3*10
Socket Cap Screws, connect it to main frame as in Fig.b10 and Fig.b11. Now we have finished
building A8R frame. Double check it again to make sure everything in the right way as in
pictures. Afterwards, time to move to next major step – Build Platform assembly.
Fig.b10 Fig.b11
STEP TWO – “Build Platform” assembly.
“Build Platform” is a function module including “hotbed” and its “ “H” support plate”, 2pcs of
420mm threaded rods, 2pcs of 390mm rods, front plate, a belt, and 12pcs M8 nuts, 12sets of
M8 Nut-Spacer-washer, to install these we need 2pcs of M8 wrench, and 2pcs of zip-tie.
Please refer to Fig.b12 and “Packing List” to pick all these elements out.
Fig.b12
USER MANUAL --Raiscube A8R 3D Printer
9
“Build Platform” includes three layers, first layer is at the bottom made by two pcs of 420mm
threaded rod along with 6 pairs of nut sets, which across back plate, middle plate, and front
plate, and each plate is locked by two pairs of M8 Nut set along the threaded rods, each pair of
nuts set on both sides of each plate. Second layer is the moving system, includes Y Axis
stepper, Belt, belt bearing behind front plate, 390mm rods, (which go through four linear
bearings beneath “H” plate, cross over middle plate and heads covered by holes of front and
back plate), “H” module. And hotbed on the top for third layer. These three layers are
combined together to form a movable “Build Platform”. In brief, what got to do is to turn Fig.b13
into Fig.b14.
Fig.b13 Fig.b14
Layer by layer, simply we divide STEP TWO into four substeps, well why not three, we need to
connect double Z threaded rods to both Z Steppers respectively. preparation for STEP
THREE.
STEP 2-1: Fasten 420 threaded rods to the frame with 4 pairs of M8 nut set. One pair of each
hole point, two pairs of each plate. Here we need two M8 wrenches, 4 pairs of M8 Nut sets,
and two pcs of 420mm threaded rods. Please refer to “video demo” in SD Card to get details of
how to stack nut set and how to place each nut set along threaded rods.
Following Fig.b15, Fig.b16 show what looks like before and after this substep.
Fig.b15 Fig.b16
USER MANUAL --Raiscube A8R 3D Printer
10
STEP 2-2: Complete installation of second layer of “build platform”. To make sure it move
smoothly, we need to insert rods through four linear bearings, and test if “H” module runs well
on 390mm rod rail. If not, adjust screws which fasten linear bearings and “H” plate until it is.
Fig.b17 and Fig.b18 are offered to help understand these actions. Let’s call this “H Train”.
Fig.b17 Fig.b18
Coming after is to integrate “H train”, front plate, and belt into printer frame. Please see Fig.b19
and get ready of these. And then place “H train” over middle plate and bury rods’ heads into
back plate, and screw 4cm distance of M8 Nut set (spacer facing front plate) along 420mm
threaded rods, add front plate to rods and lock them with threaded rods by two more nut sets.
Adjust nuts on threaded rod and front plate to cover 390mm rods. Insert belt through Y support
rack behind front plate, one head attach to “H” plate, the other mount on synchronizing pulley
and then attach to “H” plate. Please refer to Fig.b21 of how to attach belt to “H” plate.
Then Fig.b20 is what when done so far.
Fig.b19 Fig.b20
Inhaltsverzeichnis
Andere Raiscube 3D-Drucker Handbücher
