Rane SEVENTY Bedienungsanleitung

Quick-Start Guide

Rane Seventy

Setup

Serato Software

The Rane Seventy is a “Serato DJ Pro hardware unlocked” device, meaning it works with Serato DJ Pro out

of the box.

Please ensure you have the latest version of Serato DJ Pro installed:

Click here to download Serato DJ Pro

Driver Software

The Rane Seventy does not require manufacturer specic drivers on Mac operating systems, and is plug

& play with Serato DJ Pro. You may be asked to install the Rane Control Panel, which allows you to adjust

mixer settings.

On Windows you will need to install a driver available from Rane’s website, or when prompted after opening

Serato DJ Pro, while the mixer is connected.

We also recommend that you have the latest rmware installed for the Rane Seventy, which can be found

on Rane’s website.

# RANE SEVENTY CONTROL FUNCTION

1MIC 2 CONTROL / MIC 1 ECHO Turn on Mic 2 input, adjust level, tone & apply Mic 1 Echo eect

2CONTOUR CONTROLS Adjust channel & crossfader contours

3 SPLIT CUE Toggle split cue function

4HEADPHONES Connect headphones to 3.5mm and 6.5mm outputs

5 REVERSE Toggle reverse of respective channel and crossfaders

1 2 3 4

Overview

# RANE SEVENTY CONTROL FUNCTION

1POWER SWITCH Turn on Seventy

2 USB PORT A / B Connect USB cable from PC

3DECK 2 USB ACCESSORY PORT Connect Rane Twelve or other USB accessory

4 DECK 1 USB ACCESSORY PORT Connect Rane Twelve or other USB accessory

5PHONO GROUNDING POST Connect grounding cable from phono turntable connected to Deck 1 or Deck 2

6PHONO / CD SWITCH Change Deck 1 or Deck 2 between PHONO or CD input

7MIC INPUT Microphone 1 & 2 1/8” & 1/4” input

8 LINE / MIC SWITCH 1 Toggle between using Mic input 1 as Line or Mic level inputs

9LINE / MIC SWITCH 2 Toggle between using Mic input 2 as Line or Mic level inputs

10 DECK 1 INPUTS AUX or PHONO/CD channel inputs

11 DECK 2 INPUTS AUX or PHONO/CD channel inputs

12 SESSION I/O Connect input or output devices

13 BOOTH OUT 1/4” / 6.5mm booth output

14 MAIN OUT XLR output

15 AC IN AC power input

1 2 3 4 5 6 7 8

9101112131415

Overview

1 2 3 4 5

151617

# RANE SEVENTY

CONTROL

FUNCTION SHIFT FUNCTION

1CHANNEL STRIP Source Select, Channel Gain, EQ, Filter

(per channel)

2 MASTER SECTION Adjust Master volume, Booth volume -

3 BACK Cycle between Library & Waveform view Cycle fowards between respective panels

4SCROLL / LOAD Turn to scroll library, press in to load track to

deck

Fast library scroll

5 LOAD PREP Load track to prepare view Open prepare panel

6 SESSION SECTION Session controls -

7LOOP ON/OFF Turn active loop on or o Reloop / Exit

8 x2 Double active loop size Loop out / Edit

91/2 Halve active loop size Loop in / Edit

10 FX SECTION SEE FX SECTION FOR MORE INFORMATION -

11 TAP Tap to approximate FX tempo Reset Tap Tempo

12 SHIFT Used with other controls that have SHIFT

modier functions

13 CHANNEL CUE Move slider to change headphone cue adjust -

14 CUE SECTION Adjust CUE Mix / CUE Level -

15 INSTANT DOUBLES Load selected track as instant doubles -

16 CROSSFADER Crossfade audio between channel A-B -

17 CHANNEL FADER Adjust channel volume -

18 SAMPLER LEVEL Adjust Sampler volume -

19 PERFORMANCE PAD SECTION SEE PERFORMANCE PADS SECTION FOR

MORE INFORMATION

20 PARAMETER LEFT/RIGHT Adjust parameter in performance pad modes per

deck

21 DISPLAY Shows mixer information -

22 MIC SECTION Adjust Mic level, tone, toggle on/o & echo -

Overview

The Rane Seventy comes with 8 RGB Performance Pads per deck (for a total of 16 pads),

which can be used in 7 dierent pad modes, and 2 further user-mappable pad modes.

The rst 5 modes can be accessed by pressing the respective pad mode buttons once, and are as follows:

• HOT CUE mode: Pads 1-8 trigger Serato DJ Pro Cue points, and if no Cue point is present on that slot/pad, will

set a Cue point. Holding SHIFT while pressing a pad will clear the Cue point from that pad/slot. If Serato Flip is

enabled, Parameter Left & Right buttons on the left-hand side perform Flip Record & Flip Start, and Parameter Left

& Right buttons on the right-hand side perform Flip Start and Flip On/O.

• SAVED LOOP mode: Pressing pads 1-8 triggers Saved Loops, or saves the current loop to the respective loop

slot. Holding SHIFT while pressing pads 1-8 reloop the Saved Loop in that slot. Use the dedicated Loop Controls to

adjust loop size.

• ROLL mode: In this mode holding pads 1-8 activates a loop roll of varying sizes. Release the pad to exit the Loop

Roll. Use the Parameter Left & Right buttons on the mixer, to change the 8 selected loop roll size options, or hold

SHIFT while pressing them to shift the Loop Roll forward or backwards.

• SAMPLER mode: Press pads 1-8 to trigger samples loaded into the Serato DJ Pro Sampler. Hold SHIFT while

pressing a pad to stop the sample playback once triggered, or load a sample to the respective Sampler slot if no

sample is loaded. Press the Parameter Left & Right buttons to change through Sampler Banks A/B/C/D, and hold

SHIFT while pressing them to change the Sampler output 1/2/A/M.

• TRANSPORT mode: In this mode you can control virtual deck transport operation. Pad 1 & 2 control Pitch Ben

down & up, Pad 3 & 4 control Pitch Nudge down & up, while holding SHIFT and pressing pad 3 or 4 will reset pitch

to zero. Pad 5 toggles Keylock (or Pitch ‘n Time DJ if enabled), and holding SHIFT while pressing pad 5 toggles

between INT and REL or ABS playback modes. Press pad 6 turns on SYNC, and holding SHIFT while pressing pad

6 disables SYNC. Pad 7 triggers the TEMP CUE, or sets one if none is present on the loaded track. Holding SHIFT

while pressing pad 7 will return to the start of the track, and pressing it quickly again will load the previous track.

Finally, pressing pad 8 toggles between play and paused states, and pressing it while holding SHIFT toggles Stutter

Play.

Performance Pads

The next 4 modes can be accessed by pressing the respective pad mode button twice, and are as follows:

• PITCH PLAY mode: Press the ‘CUE’ mode button twice to enter PITCH PLAY mode. In this mode, pads 1-8 play

Cue points over variable pitch ranges. See the ‘Pitch Play’ section for more information.

• SAVED FLIP mode: Press the ‘SAVED LOOP’ mode button twice to enter SAVED FLIP mode. In this mode, pads

1-8 trigger Saved Flips. Holding SHIFT while pressing pads 1-8 will toggle the respective Saved Flip on or o.

Parameter Left & Right buttons on the left-hand side perform Flip Record & Flip Start, and Parameter Left & Right

buttons on the right-hand side perform Flip Start and Flip On/O.

NOTE: Serato Flip is required for this mode.

• USER mode 1: Press the ‘ROLL’ mode button twice to enter USER mode 1. In this mode, you can assign pads

1-8 to dierent functions inside Serato DJ Pro, using the MIDI mapping feature, and save it as your own pad mode.

Refer to the MIDI Mapping with Serato DJ Pro article, for more information on how to map MIDI functions.

• USER mode 2: Press the ‘TRANSPORT’ mode button twice to enter USER mode 2. In this mode, you can assign

pads 1-8 to dierent functions inside Serato DJ Pro, using the MIDI mapping feature, and save it as your own pad

mode. Refer to the MIDI Mapping with Serato DJ Pro article, for more information on how to map MIDI functions.

Performance Pads

The Rane Seventy allows for a myriad of FX, via both built-in hardware FX, and control of Serato DJ Pro’s iZotopeTM DJ-FX. The

large display built into the mixer, allows you to see FX information at a glance.

For the purpose of this guide, control of the software DJ-FX will be focused on. Please refer to the Rane Seventy user guide for

detailed information on using the hardware FX.

Click on the FX button in the upper left-hand corner of Serato DJ Pro, to expose the DJ-FX panel, then, in the DJ-

FX panel, select either multi or single FX modes.

To read more about general use of DJ-FX in Serato DJ Pro, please refer to the DJ-FX section of the Serato DJ Pro user manual.

Controls

#FX

CONTROL

SINGLE FX

FUNCTION

MULTI FX

FUNCTION

1ECHO ARM FX Unit 2 ARM FX 1 (Lit when armed). Use Eects switch to turn on or