Rane LRS4 Bedienungsanleitung
DATA SHEET / MANUAL LRS4
LEVEL RECALL SWITCH
Description
e LRS4 provides a simple interface to end users requiring four
predetermined volume levels (may include mute) when used in
conjunction with devices equipped with voltage-controlled level
inputs. Compatible Rane units include the CP64S, CP52S,
DA26S, or MP44. Units with the Versatile Input Port (VIP)
are also compatible, including the Drag Net family of RPM
products.
e LRS4 accepts a two-wire DC voltage input (VREF and
ground) and outputs a single voltage (VC) that is varied depend-
ing on the selected LRS4 button. us, four volume levels can
be setup during installation. Any button may be set to any gain
between unity and mute. Typically, 4 is set for the highest gain
with 3, 2, 1 graduating down to mute, if available.
e LRS4 ts in a standard US electrical box and can be
paired with Decora™ plates for improved architectural beauty.
e LRS4 contains four radio buttons: engaging one button (in,
changing to green) causes any of the other three to disengage (out,
changing to black).
Decora™ plate not included.
Decora is a trademark of Leviton.
1
2
4
3
Decora plate (not included)
2.35”
Vr
Vc
All features & specications subject to change without notice. DOC 105877
©Rane Corporation 10802 47th Ave. W., Mukilteo WA 98275-5000 TEL 425-355-6000 FAX 425-347-7757 WEB rane.com
Remote Mounting and Wiring
e LRS4 remote assembly mounts in a standard U.S. electrical
box with a minimum depth of 2.5" [6.4 cm]. Turn the power
to the unit o until all connections are made. It is important
to ensure that the Remote Ports are not subjected to sustained
voltages outside the range of 0 to 5 volts DC or high levels of
static. e device inputs are protected, however you can save a lot
of time by taking this precaution. It is a good idea to install the
wiring, connect it to the Remote and then make the nal con-
nections at the unit.
When wiring to Euroblocks, a minimum wire gauge of 22 is
preferred for reliability. If the ground or shield wire is left shorter,
it acts as a strain relief for the other wires. Cable with a exible
jacket is easier to use and less likely to damage the connections.
Be sure to note the wire color of each input in order to facilitate
correct wiring to the unit. Make sure wires are free of nicks and
that the cable jacket is stripped back suciently to allow it to lie
in the electrical box with the remote assembly inserted. Connect
each wire to the 5-pin connector by fully inserting it in the cor-
rect socket and tightening the screw.
Use the at head #6 screws supplied with the kit to mount
the remote assembly and silkscreened front panel to the electrical
box. Install the Decora plate of your choice (not included).
Wire Types
Variations in wire type do not greatly aect the performance
of the remote controls. However, 22-gauge stranded wire with
a exible jacket is recommended. You may use 3-conductor
unshielded remote control signal cable for shorter runs (less than
200 feet [60 meters]) or 2-conductor (1 pair) shielded remote
control signal cable (use the shield as the GND return) for longer
runs (200 to 1000 feet [60 to 300 meters]). e type of wire
required is inuenced by your installation and local electrical
codes.
Rane Corporation does not provide or source cable. Please
contact your local retail or wholesale outlet, not the factory. e
following is a short list of suitable cable types:
CONSOLIDATED ELECTRONIC WIRE AND CABLE
Plenum cable:
Unshielded remote control signal cable CAT. #9896
Shielded remote control signal cable CAT. #9877 or #9852
WEICO WIRE & CABLE INC.
Communication and control cable:
Multiconductor, unshielded CAT. #7606
ALPHA
Communication and control cable:
Multiconductor, unshielded CAT. #1175C
BELDEN
Unshielded remote control signal cable CAT. #88741
Shielded remote control signal cable CAT. #88723
Block Diagram / Schematic
Note: Older Rane units may be marked dierently. Consult this
chart if your unit does not have VR and VC terminals.
2
3
1k
1
4
5 kΩ
5 kΩ
5 kΩ
5 kΩ
1k
1k
1k
GND
CP 64LRS 4 CP 52 DA 26 MP 44 RPM *
VR VR1or2 VR REF VR REF
VC V1or2 VC VC VC 1-8
GND
VR
VC
GND
GND
Inhaltsverzeichnis
Andere Rane Schalten Handbücher
