Range Road Rr series Bedienungsanleitung

Range Road RR Series

Semi-Automatic Firewood

Processor

Crated Unit

Assembly Manual

1) Undo 8 -18mm x 19mm Nuts and bolts , 2 on each leg of top frame

2) Lift top of Metal crate off and move out of work area.

3) Remove Shrinkwrap.

4) Unwrap Wheels. (2)

a) Remove bag containing Bearing, washer, nut, cotter key and cap, place on workbench, set

unwrapped wheels out of the way.

5) Unwrap the following, place on workbench

a) sawdust chute

b) sawbar engagement arm

c) toolbox

d) fenders (2)

e) bar oil container, do not misplace the loose hose

f) towbar jack

6) Cut tiewrap holding safety covers together

7) Unwrap the following, place on workbench

a) small safety cover

b) large safety cover

c) splitter bar height adjusters and lever. (3 pieces)

d) chain engagement/speed lever

8) Cut tiewraps holding components at base of processor

9) Remove and unwrap the following, place out of way

a) log roller arm

b) axle

c) tripod leg

d) towbar

10) Lift processor off crate with forklift or crane, make sure that straps will not catch anything on unit when

tightened and that unit will be balanced.

Lift high enough to be able to install Axle, Wheels and Tripod

11) Remove lower crate from work area

12) Install Tripod leg at front of processor

13) Loosen Axle retention Bolts and lock nuts (18mm x 18mm)

14) Slide Axle through tube, make sure the bolt holes face upwards, the inner bolt hole on the battery side should be

approx. 3” from tube, tighten bolt to 75 ft. lb., tighten lock nut, repeat on opposite side

15) Grease wheel bearings

16) Install Wheel on axle

a) Install Bearing, then washer

b) Screw on Castle Nut make sure to line threads up

17) Tighten castle nut until nut is snug and wheel is hard to turn, then back the nut off ¼ turn until cotter pin hole

lines up.

18) Insert cotter pin and bend

19) Install hub cap, use a rubber mallet to press into place

20) Grease wheel hub generously through grease zerk on back of hub

Repeat on opposite side

21) Lower unit to floor

22) Install sawdust chute 10mm Nut x Phillips Screw

22) Cut tiewrap on sawbar so it can move freely (if required)

23) Bend ends of spring outwards if you want more tension on sawbar, this makes the sawbar harder to pull but

returns it to the up position quicker. Hook sawbar return spring into slot.

24) Connect hydraulic hose to saw motor, make sure hose is routed cleanly and not rubbing, connect hoses marked

“A” and “B” to the ports marked “A” and “B”.

5) Remove 10mm bolt and nut from holder above trough, keep plastic tube as well

26) Remove and keep cotter pin from large safety cage round bar

27) Put large safety cage cover into place, slide through hole in processor

drop the other end into the u clamp that you removed the 10mm bolt from

28) Re-install cotter pin

29) Re-install 10mm Bolt, tubing and nut, snug up nut, do not tighten

30) Remove 3 – 13mm Bolts and nuts for chain safety cover, make sure rear mount is slotted for cover to move

upwards for clearance as chain stretches

31) Remove 2 – 10mm Bolts and nuts for front safety cover, save plastic tubing

Andere Range Road Holzspalter Handbücher

Range Road

Range Road RR20T Series Bedienungsanleitung

Range Road

Range Road RR27T Bedienungsanleitung

Range Road

Range Road EcoPro Series Bedienungsanleitung

Beliebte Holzspalter Handbücher anderer Marken

Bell

Bell Pickpine VS S9 Gebrauchsanweisung

ATIKA

ATIKA ASP 5 N-UG Betriebsanleitung

Posch

Posch Schälprofi 500 Bedienungsanleitung

Champion

Champion 91520 Handbuch

Fieldmann

Fieldmann FZLS 1008V-E Bedienungsanleitung

Craftsman

Craftsman 247.28775 Bedienungsanleitung

Scheppach

Scheppach OX 3-1000 Montageanleitung

Swisher

Swisher 21200 Bedienungsanleitung

Elem Garden Technic

Elem Garden Technic FBHT65-22TCH Bedienungsanleitung

Champion Power Equipment

Champion Power Equipment 90720 Handbuch

Villager

Villager LSP 12 T Bedienungsanleitung

Boss Industrial

Boss Industrial ES5T20 Bedienungsanleitung

MTD

MTD 242-642A Bedienungsanleitung

Rok

Rok 150-51-50255 Bedienungsanleitung

Hakki Pilke

Hakki Pilke Raven Bedienungsanleitung

Swisher

Swisher LSRB11534 Bedienungsanleitung

Hyundai

Hyundai HYLS7TE Bedienungsanleitung

Scheppach

Scheppach HL1500M Benutzerhandbuch

Range Road rr series Bedienungsanleitung

Beliebte Holzspalter Handbücher anderer Marken