Raspberry Pi PIR Bedienungsanleitung

Pi PIR Camera Box Assembly Instructions

The laser-cut parts of the case are protected by an adhesive film which needs to be removed before assembly.

Bill of Materials

Raspberry Pi B+ / 2 / 3

Raspberry Pi Camera

6x black matte acrylic plates

1x thin clear acrylic plates

7x 1/4" black screws

1x 3/16" steel screw

3x 1" M/F hex standoffs

4x 1/4" F/F hex standoffs

6x M2 x 10mm black screw

6x M2 nut

10x M2 washer

2x M5 Screw

2x M5 Nut

4x rubber feet

Optional for wall mounting:

Wall mount

2x M5 screws

2x M5 nuts

Optional:

Magnetic lens

NOTE: Acrylic is a hard and stiff plastic which is sensitive to stress concentrations and shares a certain level of

fragility with glass. Acrylic can scratch easily and should be cleaned with a mild solution of dish detergent and

warm water. Never use cleaners unsuitable for acrylic. Never use a dry, abrasive cloth.

Here are the parts from the case kit:

Follow these images checking parts and orientation of the acrylic pieces. You will see a before and after image for

each step. Make sure you have all the parts ready, shown in the before picture.

Orientate your Pi to match the above picture and secure the 1" M/F stand offs in the bottom-left, top-left and top-

right corners using the 1/4" F/F stand offs.

OPTIONAL - Wall Mount

Attach the wall mounting bracket to the rear acrylic plate using the two M5 screws and nuts.

Now we need to attach the Pi to the rear plate using four 1/4" black screws.

Attach the camera cable to your Pi.

Attach the three jumper wires to the Pi's GPIO pins (colours may vary). Attach a wire to pin Pin 2, another to Pin

6 and the last one to Pin 26.

Next thing to do is attach the side acrylic plates. Make sure you have each of the 4 camera box walls in the correct

orientation. The arrows indicate the knotches that will be inserted into the bottom plate.

Now we need to attach our camera modle to the front plate. Start by placing the thin clear acrylic plate into

position and insert a M2 x 10mm screw into each corner mounting hole.

Carefully turn the plate over so the ends of the screws are now facing you. Place TWO M2 washers onto each of

the screws.

Add the camera module

And finally secure in place using the M2 nuts.

Inhaltsverzeichnis

Andere Raspberry Pi Computerhardware Handbücher

Raspberry Pi

Raspberry Pi PiCoolFAN4 Bedienungsanleitung

Raspberry Pi

Raspberry Pi 3 B+ Benutzerhandbuch

Raspberry Pi

Raspberry Pi ARGON ONE Pi4 Bedienungsanleitung

Raspberry Pi

Raspberry Pi 3B Bedienungsanleitung

Raspberry Pi

Raspberry Pi 4 b Gebrauchsanweisung

Raspberry Pi

Raspberry Pi S2Pi Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung