RAYLASE IPG Bedienungsanleitung

Hardware Manual

IPG Interface Board

This manual has been compiled by RAYLASE for its customers and employees.

RAYLASE reserves the right to change the product described in this manual and the infor-

mation contained therein without prior notice.

The software included in the product and this manual itself are protected by copyright. All

rights are reserved. Duplication of this manual in whole or in part, particularly by photocopy-

ing, scanning or imaging, and reproduction by any means are forbidden without the prior, writ-

ten consent of RAYLASE.

Contents

MN027 / v1.1.0 RAYLASE IPG Interface Board 3

TABLE OF CONTENTS

1BASIC INFORMATION...................................................................................................4

1.1 Delivery Scope ................................................................................................................4

1.2 Warranty..........................................................................................................................4

1.3 Signs................................................................................................................................5

1.4 Conformity with directives ...............................................................................................5

1.5 Laser Safety ....................................................................................................................6

1.6 Manufacturer ...................................................................................................................6

1.7 Customer Support ...........................................................................................................6

1.8 Disposal...........................................................................................................................6

2TECHNICAL DATA.........................................................................................................7

2.1 Dimension and Weight....................................................................................................7

2.2 Environmental Conditions ...............................................................................................7

2.3 SET-UP Procedure..........................................................................................................7

2.4 Connections.....................................................................................................................8

2.4.1 IPG Laser Interface .........................................................................................................9

2.4.2 Laser Power Input and Laser Power Output.................................................................10

2.4.3 Cable Specifications......................................................................................................10

2.4.4 Status LEDs...................................................................................................................10

3PROGRAMMING ..........................................................................................................11

3.1 Signals...........................................................................................................................11

3.2 Commands....................................................................................................................11

3.3 Programming sequence................................................................................................12

Chapter 1 Basic Information

4 RAYLASE IPG Interface Board MN027 / v1.1.0

1 BASIC INFORMATION

The RAYLASE IPG interface board is used to control a pulsed IPG laser in combination with

RAYLASE control cards SP-ICE, RLC-PCI or RLC-USB.

Features

Interface to Ytterbium pulsed IPG Fiber Lasers according to interface types B, B1, B2, D

D-SUB 25 connector for 1:1 connection to pulsed IPG laser

Detection, if 24V power is attached. Soft start to switch on the laser.

Optically isolated control signals

Detection of laser error conditions

Reset of laser after detection of laser error either by push-button or software

Support of integrated visible pointer

Emergency Stop input for immediate shut off of laser output

1.1 Delivery Scope

IPG interface board

Connecting cable between IPG interface board and control card

Laser adaptor

Hardware manual

1.2 Warranty

The rights of the customer in respect of any defects in quality or deficiencies in title are gov-

erned by the general conditions of business of RAYLASE AG. These conditions are available

for review on our website.

Before returning the product, please request an authorization number from RAYLASE. Pack

the product in the original packaging or in packaging that provides equivalent protection for

shipping.

RAYLASE shall not be obliged to repair defects under the following circumstances:

If persons not authorized by RAYLASE have attempted to repair the product.

If persons not authorized by RAYLASE have modified the product.

If the product has been used improperly.

If the product has been connected to incompatible devices.

If the product has been damaged because of inadmissible high laser power or focusing the

laser on optical areas.

If the product has been damaged because of unqualified cleaning of the optical areas.

Note: No implicit guarantee or warranty of suitability for specific purposes has been made.

RAYLASE is not responsible for damages arising from use of the product. Individual assem-

blies or other assemblies manufactured by RAYLASE may be subject to separate warranty

conditions. Refer to the corresponding manuals for further information.

Basic Information Chapter 1

MN027 / v1.1.0 RAYLASE IPG Interface Board 5

1.3 Signs

The following signs must be attached to the Interface Board. These signs may not be re-

moved. Signs that have become illegible must be replaced.

Rating plate

The rating plate and the identification code printed on it allow

the determination of the Interface Board type.

The CE symbol confirms the compliance of the Interface

Board with European directives. It indicates that the Interface

Board is approved for free trade within the EU.

The seal label warns against unauthorized opening of the In-

terface Board. If the seal is broken, all warranty claims against

RAYLASE are void.

1.4 Conformity with directives

The Interface Board conforms to the requirements of the following directives:

EU Directive 2004/108/EC (EMC)

WEEE Directive 2012/19/EC

RoHS II 2011/65/EU

For details of conformity with other directives, contact RAYLASE.

Chapter 1 Basic Information

6 RAYLASE IPG Interface Board MN027 / v1.1.0

1.5 Laser Safety

Customers assume all responsibility for maintaining a laser-safe working environment. OEM

customers must assume all responsibility for CDRH (Center for Devices and Radiological

Health) certification.

WARNING:

Switch on the PC first, before switching on the laser system. In this way you can avoid an

uncontrolled action of the laser when starting the control card.

1.6 Manufacturer

RAYLASE AG

Argelsrieder Feld 2+4

82234 Wessling

Germany

Tel.: +49 (0) 81 53 - 88 98 - 0

Fax: +49 (0) 81 53 - 88 98 - 10

http://www.raylase.de

E-mail: info@raylase.de

1.7 Customer Support

The RAYLASE support services are available for your problems either in respect to the prod-

uct or the accompanying manual. Before calling for support, please make sure you refer to

any appropriate sections in this manual that may answer your questions.

If you need further assistance call RAYLASE customer service department, Monday through

Friday between 8 A.M. and 4 P.M. (Middle European Time).

The customer service personnel will be able to give you direct assistance and answers to your

questions.

Germany (Wessling)

+49 (0) 81 53 - 88 98 - 0

... ask for the customer service department

1.8 Disposal

For the disposal of the Interface Board, note local policies, regulations and laws.

Technical Data Chapter 2

MN027 / v1.1.0 RAYLASE IPG Interface Board 7

2 TECHNICAL DATA

2.1 Dimension and Weight

Dimensions: W 85mm, L 103mm, H 30mm

Weight: 400g

2.2 Environmental Conditions

Ambient temperature: +15°C to +35°C

Storage temperature: 0°C to +80°C

Humidity rel.: 80% non-condensing

2.3 SET-UP Procedure

Make sure that all requirements for laser safety, as described in the scan head manuals, are

fulfilled. It is the user’s responsibility to follow the regulations on laser safety.

Control card IPG laser

IPG interface

board

Adap-

ter J3

Power

supply

J1J5

Shutter

Installation

Connect power supply for laser to J1.

Connect laser power supply output J2 to IPG laser.

Connect IPG interface board output J4 to laser interface.

Connect RAYLASE control card via adapter to IPG interface board input J3.

Switch on laser power supply. After a short delay, the laser will be switched on.

Please note: J5 must be connected to switch on the laser.

Fig. 1

Block diagram

Chapter 2 Technical Data

8 RAYLASE IPG Interface Board MN027 / v1.1.0

2.4 Connections

Assignment

Details

Laser Power Input (24V)

---

Laser Power Output

---

IPG Interface Input

---

IPG Interface Output

page 9

Shutter / Emergency Stop

must be connected to switch-on the laser

Laser Reset

resets the laser or the IPG interface in case of a fault

Fig. 2

IPG interface

board, overview

Technical Data Chapter 2

MN027 / v1.1.0 RAYLASE IPG Interface Board 9

2.4.1 IPG Laser Interface

Signal

25 PIN D-SUB

GND

Alarm1

MO / EE

Laser Modulation

PRR / Sync [interface type D]

Alarm2

Latch

Pointer

GND

Emergency stop

Alarm3

Alarm4

---

EE = Emission Enable

LM = Laser modulation

MO = Master oscillator [interface type B]

nc = Not connected

PRR = Pulse Repetion Rate [interface type B]

Specifications

Output

Output low

max. 0.55V

64mA

Output high

2.0 –5.0V

32mA

Chapter 2 Technical Data

10 RAYLASE IPG Interface Board MN027 / v1.1.0

2.4.2 Laser Power Input and Laser Power Output

J1, J2

Signal

1 2 3

Laser power

interconnection

24V

Return

Safety Ground

2.4.3 Cable Specifications

Connection

Cross-section

Length

Signals

24V power supply −J1

min. 3x2,5mm²

---

J2 −IPG laser

min. 3x2,5mm²

max. 2m

---

J4 −IPG laser

---

max. 2m

1:1

2.4.4 Status LEDs

LED

Meaning

green

5V Input

Voltage from control card is ready

green

24V Input

Voltage for laser is ready

red

24V Output

Soft start process of IPG laser is active.

green

IPG laser is powered up

red

Laser emission ON

Laser is active

LED

Meaning

green

Normal state

yellow

green

Laser not ready (only interface type D)

yellow *

Shutter open (combinations with other fault possible)

red

Laser temperature out of range

red

Powersupply out of range (only interface type D)

red

Back Reflection error

red*

Internal system error

* flashing

Inhaltsverzeichnis

Andere RAYLASE Computerhardware Handbücher

RAYLASE

RAYLASE SP-ICE 2 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung