Raypak Majestic ODSR36A Kurzanleitung

MAJESTIC

OUTDOOR / INDOOR WOOD FIREPLACES

Model: ODSR36A

OWNERS INSTALLATION & OPERATING INSTRUCTIONS.

KEEP THESE INSTRUCTIONS FOR FUTURE REFERANCE.

CONTENTS

Part 1: Safety Information

Part 2: Installation Instructions

•Outdoor Installation

•Planning Information

•Mounting the Fireplace

•Framing

•Flue Installation

•Flue Offset Installation

•Positioning, safety Strips, Securing the fireplace

•Chase Installation

•Clearances

•Sidewall Protection

•Hearth Installations

Part 3: Warranty

Part 4: Additional Accessories

Part 5: Spare Parts List

Description

The model ODSR36A is a clean faced solid fuel wood burning fireplace

and is approved for Outdoor and Indoor installation when used with

the appropriate flue system.

Part 1: Safety Information

Please read these instructions prior to installing and

operating this appliance.

Warning: This appliance must be installed by a licensed

person. This appliance and flue system must be installed in

accordance with AS/ ANZ 2918 and the appropriate

requirements of the relevant building code or codes.

BEFORE INSTALLING YOUR APPLIANCE

Carefully read and understand all the instructions.

1. THIS APPLIACE IS HOT WHILE IN OPERATION KEEP

CHILDREN, CLOTHING AND FURNITURE AWAY, CONTACT MAY

CAUSE SKIN BURNS.

2. DO NOT INSTALL IN GARAGE OR NEAR FLAMMABLE FLUID

Check with the building inspector for compliance with local codes; a

permit may be required.

3. This appliance must be installed using Raypak approved flue kit and

installed as per the Australian standard AS/ANZ 2918 codes

This appliance must be flued directly off the appliance and discharged

to atmosphere.

4. DO NOT connect to any duct work to which another appliance is

connected.

5. DO NOT connect this unit to a chimney flue that is serving another

appliance.

6. DO NOT USE CHEMICALS OR FLUIDS TO START THE FIRE.

7. The flue should be inspected periodically and cleaned if necessary.

8. DO NOT store wood, flammable liquids or other combustible materials

close to the unit.

9. Contact your local fire authority for information on how to handle a

chimney fire. Have a clearly understood plan to handle a flue fire, turn

air control to the closed position and call the fire brigade.

10.DO NOT tamper with the combustion air control beyond the normal

adjustment.

11.DO NOT install combustible materials on the fire place surround.

This fire place is not designed to be a water tight fireplace. When

installing this unit against an external wall, the wall must be finished

before setting the unit in place.

12.Always leave the damper in the open position while the unit is in use

Once the required draw is obtained, close mesh screen to protect from

sparks that may occur.

13.DO NOT install these units into a mobile home or caravan. These units

are NOT mobile home approved.

Part 2: Installation Instructions

•OUTDOOR INSTALLATION

Read this manual prior to beginning this installation and check

that you have been provided with the correct components

necessary to carry out the installation.

1 Remove all parts from inside the fire box.

2 Check outdoor flue kit part number: ODSSFLKT

Contents

•1 x 203 x 1220 mm ( 8’) Inner stainless steel flue

•1 x 279 x 1100 mm ( 11‘) Outer stainless steel flue

•1 x Stainless Steel Cowl

•1 x Powder coated vented dress ring . # This vented dress

ring will only be required to be used ( situated on top of the

fireplace enclosure to provide ventilation within the enclosure )

when the fireplace is in a free standing position and the flue is

exposed above the fireplace housing, this applies for both

Indoor and Outdoor installations

Note: If this unit is installed outdoors and the flue is to be

installed in a chase construction ( see Fig 6 ) or requires a

roof penetration ( pergola or veranda ) you must use the

Indoor flue kit part number: ODIDSSFLKT

Select the location for the appliance. This appliance must not be installed

inside minimum clearances to the house and any combustibles materials as

shown in Fig 1 & Fig 2

WARINING: FAILURE TO FOLLOW THE MINIMUM CLEARANCE

REQUIREMENTS MAY RESULT IN AN UNSAFE INSTALLATION.

Fig 1 Specifications & Framing layout

Fig 2 Free standing installation

Note: If the fire place is a free standing unit, it must be located a minimum

of 3m from the opening of the fire box to combustibles structure. A minimum

height of 1.9m measured from the base of the fire box to the flue termination

cowl is permitted.

•Planning Information

Preplanning an installation is very important to ensure safety, and to save

time and money. An installer must predetermine where a fireplace will be set

and how the flue system will be run.

•Mounting the Fireplace

A fireplace may only be mounted on a non combustible surface.

The fire place must be spaced 13 mm from a combustible back wall and 13

mm from either side wall or support.

•Framing

Option 1 Framing can be constructed before or after the fire place is set in

place, however most installers build the frame prior to fitting the fire place in

position Framing the fire place with 50 x 100 mm timber or heavier. Refer to

Fig 1 for framing dimensions.

Option 2

Brick or block work to create the fire place surround.

Use only Raypak Outdoor flue kit part number: ODSSFLKT

or Raypak Indoor / outdoor flue kit part number: ODIDSSFLKT

Determine how the flue will be run, length of run and flue components

required to complete the job. Never install a flue below minimum heights.

In planning a flue system, it is important to know the following.

1A flue cannot be offset more than 45 deg from a vertical plane.

2 A flue may run straight up or it may be necessary to offset it to avoid

obstructions.

3 A maximum length of an angled run ( total flue system is 500mm )

4No more than 2 offsets (2 total 45 deg c elbows ) per fireplace may be

used.

5 A guy wire stabilizer is required for flue extended more than 1.8m above

the roof line.

•Flue Installation

Where the flue penetrates the roof a suitable flashing will be required.

Fig 3

Straight Up flue Installation

To mark the centre line of the flue , put the fireplace in final position and

measure out from the wall 235mm. Mark a spot on the ceiling directly above

the fireplace. Draw a line parrallel to the back wall through this mark.

(Refer Fig 4)

Fig 4. Locate centreline of flue with plumb line.

•Offset Installation

In order to clear an obstruction, it may be necessary to offset flue from

vertical. This is accomplished by using 2 x 45 deg °offsets elbows.

Option 1: Twin skin Raypk Offset kit part number: DSSSOKT

Option 2: Triple skin Raypak Offset kit part number: TSSSOKT

•Positioning, safety Strips, Securing the fireplace.

Slide the fire place into position. Four nailing flanges are incorporated on

each corner of the surround. Bend the nailing flanges out, level the box, then

secure it firmly in place by nailing the flanges to the framing members as

shown in. Fig 14

Fig 5 Fasten fireplace into position

•Chase Installation

A chase is a vertical boxlike structure which encloses the fireplace and flue.

Chases are typically built on the outside of the house or free standing with

fireplace opening cut into the outer wall of a room. (Fig 6) This structure with

the exception of 10 mm externally ventilated air gap (total area 9,268 mm2 )

around the 285 mm flue casing at the ceiling penetration

Fig 6 Fireplace and chase parts identification

•Clearances

The following information provides minimum clearances that are required

when the installation is indoors or outdoors in a chase construction.

13 mm

Air space 40mm Air space required

13 mm Air space

to sides

Fig 7 Minimum clearances to combustibles

Fire stop (ceiling ring) must provide a minium of 9300mm2 of venting of

enclosure ( eg 10 mm gap around the outer flue casting at ceiling penetration

) where fireplace and flue casing are fully enclosed to ceiling level.

Note: The venting ring must be fitted in all cases when the flue

leaves the fireplace enclosure to ensure the correct air flow around

the case of the fire place.

Inhaltsverzeichnis

Andere Raypak Kamin im Innenbereich Handbücher

Raypak

Raypak VERMONT RFSDV34RFNAU Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch