Raytec VARIO2 series Handbuch

Quick Setup Instructions

VARIO2 iPPoE Series

2 iPPoE

Box Contents

VARIO2 IP PoE Illuminator - Infra-Red (IR) or White-Light (WL)

35° x 10° beam angle IHD ; 60° x 25° beam angle IHD

Waterproof RJ45 connector

Accessories (optional):

80° x 30° beam angle IHD

120° x 50° beam angle IHD

System requirements: A PC running Windows with network

access running a modern web browser

Full detailed instructions available from the Raytec website

Installation by suitably trained and qualied personnel only

Suitable for Internal and External Applications

0610-D-00008-1

2rayteccctv.com Raytec Global Tel: +44 (0) 1670 520055

Americas Tel: +1 613 270 9990

Safety Information

Install in a well ventilated area

Eye Safety : IR Variants (850nm and 940nm)

Caution – EN62471 Risk Group 2 Classification - IR emitted from

this product. Do not stare at the lamp. Avoid exposure or use

appropriate shielding / eye protection.

For VAR2-IPPOE-i4-1, VAR2-IPPOE-i6-1, VAR2-IPPOE-i8-1 and

VAR2-IPPOE-i4-2, VAR2-IPPOE-i6-2 variants hazard distance is

1900mm (Risk Group 1 distance 800mm).

For VAR2-IPPOE-i4-3, VAR2-IPPOE-i6-3, VAR2-IPPOE-i8-2/-3

variants hazard distance is 2700mm (Risk Group 1 distance 900mm).

Eye Safety : White Light and 730nm variants

Caution – EN62471 Risk Group 2 Classification - Possible hazardous

optical radiation emitted from this product. May be harmful to eyes,

do not stare at the lamp. For VAR2-IPPOE-w4-1, VAR2-IPPOE-w8-1

and VAR2-IPPOE-w4-2 variants hazard distance is 1500mm.

For VAR2-IPPOE-w4-3, VAR2-IPPOE-w8-2/-3 variants hazard

distance is 1840mm.

Eye Safety: Other Wavelengths - Contact Raytec.

The Illuminator is Class III for insulation

Illuminators are suitable for use Outdoors and Indoors

Product Introduction

VARIO2 IP PoE is a Network Illuminator designed to connect to a suitable network

and is provided with an integrated Web Interface. The Raytec DiscoMan Tool

allows for easy identication and connection to the illuminator or you can connect

directly to the illuminator via its IP address.

The illuminator has a CAT 5 cable for data connection, can be powered from PoE,

and is supplied with a waterproof CAT 5 connector. The illuminator also has an

auxiliary cable if low voltage 24V DC operation is preferred.

rayteccctv.com

Raytec Global Tel: +44 (0) 1670 520055

Americas Tel: +1 613 270 9990

PoE Detection

Resistance Selection

Hard Reset

Button

Interchangeable

Lensing

Please note: base plate

has been removed for

illustrative purposes.

Please note:

Waterproof connector

is supplied loose –

and is shown tted for

illustrative purposes

Auxiliary Cable

Optional 24V DC power input – red (+ve)

& black (-ve)

External Input, volt free or TTL – orange

(TTL +ve) & purple (TTL GND)

External Output, volt free – yellow & white

CAT 5 Cable

for Data and

Optional PoE

Photocell

The illuminator has a photocell for automatic day/night switching and has an

External Input (to act as a telemetry, trigger input, volt free or TTL) and an External

Output (volt free output). It also benets from Raytec’s interchangeable lens

system so that the correct angle of illumination can always be achieved easily.

The illuminator has Operator and Administrator log-in and access rights. The

Operator has access to the Homepage and Diagnostic pages. The Administrator

has access to all pages.

An API is available for programmers for integration within a VMS / BMS

environment. The illuminator also has a HTTP API to control the illuminator via

HTTP commands.

4rayteccctv.com Raytec Global Tel: +44 (0) 1670 520055

Americas Tel: +1 613 270 9990

Basic Steps

(Quick Installation Guide Pg. 1-20)

STEP 1: Safety Information (Pg. 2)

STEP 2: Wiring Installation (Pg. 6)

For PoE, use standard CAT 5 or better for both power and data. For all 8 sized

products, check the PoE detection resistance of the illuminator is compatible with

your PoE equipment (24.9KΩ class 6 is factory default).

For low voltage (non-PoE) apply 24V DC to red and black cores of auxiliary cable

and use standard CAT 5 or better for data connection. Connect external inputs

and external output wires as required.

IMPORTANT:

Ensure PoE equipment or 24V PSU are suitably rated

For 8 sized products check PoE detection resistance is set

correctly

Ensure Cat 5 cable and auxiliary cable are correctly terminated

and waterproofed after installation

If using low voltage, a CAT 5 cable must still be connected to

the network for communication

If not using auxiliary cable, it must still be suitably terminated

and waterproofed

STEP 3: Physical Installation (Pg. 9-10)

Adjust interchangeable lens if required.

Fix to wall, pole or camera unit using U bracket provided or other Raytec bracketry.

IMPORTANT:

Ensure illuminator is rated to provide required viewing distances

and select correct angle

Ensure illuminator is orientated in the correct direction

rayteccctv.com

Raytec Global Tel: +44 (0) 1670 520055

Americas Tel: +1 613 270 9990

STEP 4: Change IP address and connect to the illuminator (Pg. 11)

We recommend the easiest and fastest way to identify and connect to illuminators

is using the Raytec DiscoMan Tool where the IP address can be altered

IMPORTANT:

We recommend Raytec DiscoMan Tool as the easiest way

to establish communication. If using IP address for direct

communication, illuminator and computer must be in same

network range.

STEP 5: Illuminator Set-Up (Pg. 12-18)

Raytec DiscoMan Tool Basics

Log-in, Security & Basic Illuminator Setup

Basic Web Page Functionality

STEP 6: Basic Troubleshoot (Pg. 19)

Note :

The external cables cannot be replaced. If one is damaged and the

customer is unable to shorten and re-use the cable, the illuminator must

not be powered.

6rayteccctv.com Raytec Global Tel: +44 (0) 1670 520055

Americas Tel: +1 613 270 9990

Wiring

The illuminator is supplied with a terminated CAT 5 cable with a waterproof Ethernet

connector (supplied loose i.e. not tted) and an auxiliary multi-core cable.

Option 1 – Power via PoE

Connect an Ethernet cable (category 5 or better) using the T-568B wiring standard

between the Power Sourcing Equipment (PSE) and the illuminator. Ensure that

the PSE is sufciently rated to power the VARIO2 IPPoE device as follows:

The Factory Software version of the illuminator is shown by characters 4,5,6 in

the product serial number.

The CAT5 cable is both the power and data connection for the illuminator. The

maximum Ethernet cable length is 100m (328 ft) without boosting the signal.

Ensure you make a waterproof connection to the RJ45 as shown below. Ensure

the connector is waterproof and sealed after the connection is made.

To illuminator RJ45-RJ45 connector To Network

Model PoE Requirement

VAR2-IPPoE-w4-1, i4-1, i4-1-C, i6-1 IEEE 802.3at ≥25.5W

VAR2-IPPoE-w8-1, i8-1, i8-1-C Factory Software Version <2.5.0: 4-pair

PoE ≥51W

Factory Software version ≥2.5.x : IEEE

802.3bt or 4 pair PoE ≥51W

rayteccctv.com

Raytec Global Tel: +44 (0) 1670 520055

Americas Tel: +1 613 270 9990

Option 2 – Power from 24V DC

If using low voltage power, connect 24V DC to the red (+ve) and black (-ve)

cables of the auxiliary cable. In this case the Ethernet cable is a data connection

only.

For either Option 1 or Option 2 above, connect external input trigger and external

output as required – see table below:

WARNING: To maintain the IP rating of the product the multi-core auxiliary

cable must be waterproofed and terminated appropriately even if it is not

in use.

PoE Detection – Resistance Selection Switch

There is a 3 way switch on the VAR2-IPPoE-w8-1, i8-1 and i8-1-C illuminators

which can be used to change the PoE detection resistance and the PD class of

the illuminator (24.9KΩ and PD class 6 is the factory default setting – Left Hand

Position).

The majority of PSE equipment require a detection resistance of 24.9KΩ to

establish a PoE. The illuminator then uses a class resistance to identify how

much power is required.

To allow the VAR2-IPPoE 8 size product to be compatible with a large range of

PSE devices the switch can be congure as follows

Colour Description Wire Gauge (AWG)

Orange External Input - Volt free or TTL +ve 22

Purple External Input - Volt free or TTL GND 22

Yellow External Output - Volt free 22

White External Output - Volt free 22

8rayteccctv.com Raytec Global Tel: +44 (0) 1670 520055

Americas Tel: +1 613 270 9990

Switch

position

Detection

Resistance

Class Comment

Left

(default)

24.9K Ω 6For use with 802.3bt compliant PSE’s.

This setting is also compatible with

most legacy products high power PSE.

Central 24.9K Ω 4Compatible with legacy single signature

high power PSE using class 4 power

negotiation.

Right 12.5 K Ω 4 Compatible with Phihong non standard

high power PSE.

For further information regarding the compatibility check with the supplier of your

PSE equipment.

To change the switch setting, turn OFF the power to the illuminator, remove the

baseplate and access the switch as shown.

Detection Resistance Selection Switch

Baseplate xing screws: Torque 0.6Nm

rayteccctv.com

Raytec Global Tel: +44 (0) 1670 520055

Americas Tel: +1 613 270 9990

Step 1

Unscrew

baseplate

Step 2

Remove

baseplate

Step 3

Remove /

Replace

diffuser lens

Step 4

Replace

baseplate

& tighten

Interchangeable Lenses: Changing the Angle

The illuminator is delivered with a 35obeam angle. To alter to 10o, remove the

baseplate from the bottom of the product and remove the existing lens and then

re-attach the baseplate securely. With no lens insert the product produces a 10o

beam angle.

To alter to any other angle, remove the existing lens and insert the required lens

which will have its angle indicated on it. Ensure the baseplate is securely re-

attached to maintain waterproof integrity of the product.

The angles available as standard are: 10°x10° (NO lens / diffuser in place),

35°x10° and 60°x25°. Other angles are available to order: 80°x30° and 120°x50°.

Baseplate xing screws: Torque 0.6Nm

10 rayteccctv.com Raytec Global Tel: +44 (0) 1670 520055

Americas Tel: +1 613 270 9990

Installation

VARIO2 IP PoE is delivered as standard with a bracket at the bottom of the unit.

This can be moved to the top of the unit if required.

Attach illuminator to wall, housing or pole using U-bracket provided or dedicated

Raytec bracketry.

Connect lamp to PSE and network

Notes:

Unit can alternatively be powered by 24V DC if required

Multi-core auxiliary cable also tted to unit

• Use for alternative power (24V DC) if required

• Use for connecting external input and external output as required

To maintain the IP rating of the product, any cable not in use must be waterproofed

and terminated appropriately.

3 4 5

Position illuminator

adjacent to camera and

point towards scene (Optional

night set-up for optimum

image performance)

Adjust vertical position

of illuminator to ensure

full eld of view illuminated

Tighten all xings

TARGET

Connect Illuminator to PSE and network using

waterproof connector:

Installers can extend or reduce lead length using

appropriate cable and weather proof box.

Mount illuminator

Andere Handbücher für VARIO2 series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Raytec Beleuchtungsausrüstung Handbücher

Raytec

Raytec VARIO2 IP 16 Series Bedienungsanleitung

Raytec

Raytec VARIO2 series Bedienungsanleitung

Raytec

Raytec VARIO2 w8 Bedienungsanleitung

Raytec

Raytec SPARTAN SPX Series Bedienungsanleitung

Raytec

Raytec SPI WARRIOR Series Bedienungsanleitung

Raytec

Raytec WARRIOR Bedienungsanleitung

Raytec

Raytec PULSESTAR VTR Bedienungsanleitung

Raytec

Raytec VAR2 IPPOE i4-1 Bedienungsanleitung

Raytec

Raytec PULSESTAR VTR6 Bedienungsanleitung

Raytec

Raytec RAYMAX WARRIOR Bedienungsanleitung

Raytec

Raytec SPARTAN HP series Bedienungsanleitung

Raytec

Raytec RAYMAX RM200 Bedienungsanleitung

Raytec

Raytec RL F 25 Bedienungsanleitung

Raytec

Raytec SPARTAN Series Bedienungsanleitung

Raytec

Raytec PULSESTAR VTR4 Bedienungsanleitung

Raytec

Raytec VARIO2 VAR2-i2-2 Bedienungsanleitung

Raytec

Raytec vario2ip HYBRID Montageanleitung

Raytec

Raytec SPX SPARTAN Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung