Razorgage Cyclone Bedienungsanleitung
Cyclone Upcut
Cut off saw
Operation manual
The operator must thoroughly read and
understand this manual before operating the cut
off saw or starting any servicing. All safety and
warning instructions should be followed. This
manual must be available to all o
p
erators.
WARNING
1
Addendum to razorgage upcut saw manual
Grease requirements for up cut saw.
Your Razorgage upcut saw should be greased after 5000 cut cycles, if dust generated by
the material cut is greater, then adjust cycle count lower. Grease all bearings with 2
pumps of grease use good quality medium weight grease. Wipe dust off of zerks before
attaching grease gun.
2 pumps all locations.
DISCONNECT SAW FROM POWER BEFORE
SERVICING !
WARNING
The top clamp contains 2 bearings follow directions for access to bearings.
It maybe necessary to remove cylinder clevis pin to allow grease gun access to bottom
grease zerk. Remove hairpin and slide clevis pin out of rod end, push rod down to allow
more clearance to bearing zerk.
Replace clevis pin and hairpin clip. Replace top clamp cover.
Bearings on material roller clamps can be greased when ever necessary to maintain
smooth motion of handles.
Be sure all components and covers are replaced before restoring power to saw.
Remove
screws and
cover
Grease
points
Hairpin clip
Clevis pin
2
Contents
General safety rules for woodworking machinery 3
Safety rules for cut off saw 6
Arrival inspection 7
Major components 8
Cutting capacity chart 10
Installation 11
Saw operation 15
Changing blade 17
Adjustments 19
3
General Safety Rules for Woodworking
Machinery
1. For your own safety, read the operation manual carefully. Know your
machine. Learn its applications and limitations, and any hazards specific to
this machine. All personnel should be trained in the operational procedures
and received safety instruction before operating this equipment. If you
have not received proper training in the use of this machine, DO NOT
OPERATE THIS MACHINE, damage to the equipment or injury to the
operator is possible.
2. This machine should not be operated without all of the guards in place and
safety devices in operation. Removal of any guards or disabling any of the
safety devices may result in damage to the equipment or injury to the
operator. If any of the guards or safety devices are missing, damaged or
not working properly, DO NOT OPERATE THIS MACHINE, notify your
supervisor immediately.
3. If the operator has any safety concerns or questions regarding the
operation of this equipment, DO NOT OPERATE THIS MACHINE, the
machine should be locked out and your supervisor notified immediately.
4. All Lock Out/Tag Out procedures must be followed before servicing or
adjusting this equipment. If you have not received proper training in the
Lock Out/Tag Out procedures for this machine, DO NOT OPERATE THIS
MACHINE,damage to the equipment or injury to the operator is possible.
WARNING
Do not attempt to operate until you thoroughly
read, and understand completely, all
instructions and rules in this manual. Failure to
comply could result in serious injury or accident
involving fire, or electric shock. This manual
must be accessible to any operator of saw and
its frequent review should be part of a
continuous safety program.
4
5. In case of any equipment malfunction or jam the machine should be
powered off and locked out before clearing any materials from the
operational areas of this machine. Once cleared the reset procedures
need to be followed when powering up the equipment. At no time should
any of the machine control systems including electrical, hydraulic or
pneumatic circuits be manually overridden.
6. Check machine for damaged parts. Before continued machine use any
damaged guard or part must be carefully checked for proper operation of
its intended function. Check all moving parts for proper alignment, check
for binding of moving parts, breakage of parts, proper secure mounting,
and any other condition that may affect machine operation. Guards or other
parts that are damaged must be properly repaired or replaced.
7. Machine must be properly grounded.
8. Maintain and clean machine at recommend intervals. Intervals may need to
be adjusted due to work load or material type to keep machine in top
condition. Follow instructions for lubrication, setup, and changing
accessories.
9. Disconnect machine from power source before, changing accessories, or
any servicing activity.
10. Avoid accidental starting. Make sure switch is in the off position before
connecting to power.
11. Remove any tools or loose objects from work surface of machine. Make
sure any tools used for adjustment or maintenance are removed from
machine before machine is restarted. Make a habit of scanning for tools
and scraps every time the machine is started.
12. Keep work area clean. Cluttered work areas and workbenches increase the
likelihood of an accident.
13. Do not use in dangerous environments. Do not use machine in damp or
wet locations, or expose them to rain. Keep work area well illuminated.
14. Keep children away. All visitors should be kept at a safe distance from
work area.
15. Make workshop childproof, with padlocks, master switches, or by removing
starter keys.
16. Do not force the machine. It will function better and safer at its designed
rate.
5
17. Use the right tools. Do not force the machine or attachments to do a job for
which they were not designed. Contact the manufacturer or distributor if
there is any question about the machines suitability for a particular job.
18. Use only recommended accessories. Consult the operation manual for
recommended accessories.
19. Wear proper apparel. Avoid loose clothing, gloves, neckties, rings
bracelets, or jewelry which could be tangled in moving parts. Keep long
hair contained to prevent entanglement. Non-slip footwear is
recommended.
20. Always wear safety glasses.
21. Secure the work piece.
22. Keep proper footing and balance at all times.
23. Do not use machine while under the influence of drugs, alcohol, or any
medication.
24. Always wear a face mask or dust mask if operation creates excessive dust
or chips. Always operate machine in a well ventilated area and provide
proper dust removal.
25. Never leave machine running unattended. Turn power off. Do not leave
machine until it comes to a complete stop.
6
Safety Rules for Cut-Off Saw
1. Read and understand the operation manual before operation.
2. Keep hands away from the cutting area.
3. Before making any adjustments disconnect all power sources including
electrical and pneumatic.
4. Minimum air pressure is 50 psi, DO NOT operate saw if minimum air
pressure is not available. Normal working pressure is 80psi.
5. At the start of each work session turn on saw and trigger the two hand trip
with no work piece present, cycle the saw and check for normal operation
of top clamp and blade advance cylinders. Turn off saw and as the motor
slows and comes to a stop check for correct rotation direction compared to
arrow indicator.
6. Do not cut warped wood; work piece should lay flat on table without
rocking.
7. Use infeed and outfeed supports when cutting long work pieces.
8. Set top clamp stop pin to limit opening height to only what is required to
process the work piece.
9. Never place hands under top clamp; remove cut piece by pulling it out from
under open top clamp. Short trim scraps should only be removed by
pushing them out with a scrap piece.
10. Always use push roller handles to position and guide work piece against
fence. Do not use hands to support work piece.
7
When your saw arrives,
The saw ships complete on one pallet, if ordered with stop the stop will be in
separate crate.
Unpack the saw ensuring that all parts are present and free from damage. If
any parts are missing or damaged contact your local distributor immediately.
Do not assembly or attempt to operate saw without all components present
and in undamaged condition.
Saw specifications Cyclone upcut
Saw blade speed 3450 rpm
Saw motor 7-1/2 hp, 230vac or 480 vac
Saw blade dia. (optional) 500mm, or smaller see capacity chart
Saw arbor size 1”
Exhaust duct dia. 4”
Cycle operation Pneumatic factory set at 80PSI
Table size 371/8 (943)w x 21-1/2 (546)d
Weight 600lbs
Inhaltsverzeichnis
Andere Razorgage Gesehen Handbücher
