RCA RCU500 Bedienungsanleitung

RCU500

Universal

Remote Control

•

PLAY FFREW

STOP PAUSE

REC

ENTER

DSPY

MUTE PREV CH

123

789

INPUT TV•VCR

UNEM

PROG

EDOC

SRCH

RAELC

DONE

••

SWAP

PIP

FREEZE

MOVE

–+

MOVE PIP

SYSTEM

LINK AV

•

TABLE OF CONTENTS

Button Description .............................................2

Setting Up Your Universal Remote ...................2

Programming Your Universal Remote

Code Search..................................................3

Code Lists .....................................................4

Operating a TV...................................................5

Operating a Cable Box ......................................6

Operating a Satellite Receiver............................6

Operating A VCR................................................7

Operating a Laserdisc Player .............................8

Operating Audio Equipment..............................9

Operating A TV/VCR Combo ..........................10

Special Operations............................................10

Code Lists

TV................................................................11

VCR .............................................................12

Laserdisc Player..........................................13

Satellite Receiver ........................................13

Cable Box ...................................................13

TV/VCR Combinations...............................13

Audio Equipment .......................................14

Warranty...............................................Center Card

This Universal Remote Control is compatible with

most models of infrared controlled Televisions,

VCRs, Cable Boxes, and Audio Equipment

manufactured after 1984. Please retain this guide

for future reference.

Place Batteries in the remote

1. Remove the battery compartment cover.

2. Place four AAA batteries as shown,

matching the + and – end of each battery as

indicated in the battery compartment.

3. Replace the cover.

Determine if your remote needs programming

Some RCA, GE and ProScan devices may already be pre-programmed.

1. Press the button of the device you want to

control (for example TV).

2. If the device turns on, press another button,

to confirm (for example CHANNEL UP).

3. If the device you selected (TV) responds,

you will not need to program the remote.

If the device you selected (TV) does

not respond, you will need to program

the remote. (See pages 3-4 for

programming instructions).

4. Repeat steps 1-3 for other devices.

Button Description

•

PLAY FFREW

STOP PAUSE

REC

ENTER

DSPY

MUTE PREV CH

1 2 3

7 8 9

INPUT TV•VCR

UNEM

PROG

EDOC

SRCH

RAELC

DONE

••

SWAP

PIP

FREEZE

MOVE

–+

MOVE PIP

SYSTEMLINK AV

•

Code Search Button

Programs devices by

searching through brand

codes. Use when code lists

are not available or when

the listed code does not

work with your device.

See page 3.

Device Buttons

(VCR1, VCR2•LD,

SAT•CABLE, AUDIO, TV)

Determines which device

you are controlling.

Channel and Sound

(DSPY, ENTER, VOL,

CHAN, MUTE, PREV CH)

Use these buttons to control

sound and channel changes.

VCR Buttons

(TV/VCR, REW, PLAY, FF,

REC, STOP, PAUSE)

Use these buttons to control

playback from a VCR or

Laserdisc Player. Also used

to record onto a VCR tape.

Number Buttons (0-9)

Use these buttons to directly

enter channel numbers for a

TV, VCR and Cable Box.

Also used for accessing pre-

set channels of an AM/FM

tuner or entering disk and

track numbers for a CD play-

er. Also used for entering

program code numbers from

brand lists.

Setting Up Your Universal Remote

•

Menu Buttons

(MENU•PROG, MOVE, –, +,

G,H) Use these buttons to

adjust on-screen menu

features and programming

information.

PIP Buttons

(PIP, MOVE PIP, SWAP,

FREEZE) Use these buttons

to adjust the Picture-in

Picture feature if it is

available on your TV.

Programming a Device using CODE SEARCH

1. Manually turn on your device

(TV, VCR, Laserdisc Player, Satellite

Receiver, Cable Box or Audio Equipment).

2.Press and hold CODE•SRCH.

3. Press and release the device button you

want to set up (TV, VCR1, VCR2•LD,

SAT•CABLE, or AUDIO).

4. Release CODE•SRCH.

5. Press POWER repeatedly until the device

turns off (you may have to press up to

100 times).

6. Once the device turns off,

press and release ENTER.

7.With the device on, press another button,

for example CHANNEL UP. If the device

responds, no further programming is

required. If the device does not respond,

repeat steps 1-7.

Programming Your Universal Remote

The remote may already be set up to operate your brand of TV, VCR, Laserdisc,

Satellite Receiver, Audio Equipment, or Cable Box. It is pre-programmed with the

following codes: TV-000, VCR1-000, AUDIO-003, and SAT•Cable Box-000. For

brands that require programming, there are two ways to program: Using Code

Lists or Code Search. Use Code Search if the code lists are not available or if the

codes from the lists do not operate a device.

ENTER

CODE

•

PRESS

& HOLD

RELEASE

EDOC

SRCH

•

EDOC

SRCH

•

Programming Your Universal Remote

Programming a Device using the Code Lists

1.Find codes for each device and brand on

page numbers shown below.

2. Press and hold the TV, VCR1, VCR2•LD,

SAT•CABLE, or AUDIO button you want to

set up.

3. Enter the three digit code from the

TV, VCR, Laserdisc Player, Satellite Receiver,

Cable Box, or Audio code list.

Device Page

TV 11

VCR 12

LaserDisc Player 13

Satellite Receiver 13

Cable Box 13

Audio Equipment 14

4. Release the device key.

5. With the device on, press another button, for

example CHANNEL UP. If the device

responds, no further programming is

required. If the device does not respond,

repeat 2-4 using another code.

Enter your device codes here for easy reference.

1 2 3

7 8 9

RELEASE

ENTER

YOUR

CODE

TV CODE

SAT•CABLE CODE

VCR1 CODE

AUDIO

VCR2•LD CODE

•

PRESS

& HOLD

Turning the TV On and Off.

Press TV to set the remote to control the

TV (Most RCA, GE and ProScan models will

only turn on when TV is pressed,

not POWER.)

2. Press POWER to turn the TV on or off.

Change Channels on the TV

Press CHANNEL UP or CHANNEL DOWN

to change channels on the TV or enter the

channels as you would normally for

your TV.

Use the buttons below to adjust features on

your TV.

DISPLAY – Shows displays on the screen and

clears menus from the screen.

MUTE – Switches the TV sound on or off.

PREV CH (PREVIOUS CHANNEL) – Changes

back and forth between two channels. Select a

channel using the number buttons and then

select another. Press PREV CH to switch

between the two channels.

If your TV has picture-in-picture, you may be

able to use the following buttons to adjust PIP.

PIP (PICTURE-IN-PICTURE) – Turns the small

picture on or off.

PIP MOVE – Moves the small picture to the

next corner.

SWAP – Switches the channel in the small

picture with the big picture.

FREEZE – Freezes or unfreezes the small

picture.

You may want to experiment with the remote to

determine all the buttons which will work with

your TV.

Operating A TV

•

ENTER

DSPY

MUTE PREV CH

SWAP

PIP

FREEZE

MOVE PIP

Turning the Cable Box On and Off.

1. Point the remote at the cable box

and press SAT•CABLE.

2. Press POWER to turn it on or off.

Changing Channels on the Cable Box.

Press CHANNEL UP or DOWN to change

channels on the cable box or enter the

channel as you would normally for your

cable box.

Turning the Satellite Receiver On and Off.

1. Point the remote at the Satellite Receiver

and press SAT•CABLE.

2. Press POWER to turn it on or off.

You may want to experiment with the

remote to determine all the buttons which

work with your Satellite Receiver.

Operating A Cable Box

Operating A Satellite Receiver

•

Turn the VCR On and Off.

1. Press VCR1

VCR2•LD to set the remote

to control the VCR.

(Most RCA, GE and

ProScan models will only turn on when

pressing VCR not POWER).

2. Press POWER to turn the VCR on or off.

Watch a tape in your VCR.

1. Turn on the VCR.

2. Insert a tape in the VCR.

3. Press PLAY to start the tape.

4. Press STOP when you are finished.

5. Press REW to rewind the tape.

6. Press PAUSE to pause the tape.

Record one channel and watch another.

1. Press VCR1

VCR2•LD to set the remote

to control the VCR.

2. Tune the VCR to the channel

you want to record.

3. Press REC to start recording.

4. Press TV/VCR.

5. Press TV to set the remote to control the TV.

6. Press CHANNEL UP or DOWN to

change channels on the TV.

7. To see the channel you are recording,

tune the TV to channel 3 or 4

(same as CH3/4 switch on the VCR). Tune

to 90, 91, or 92 for some RCA, GE or

ProScan products.

Operating A VCR

•

PLAY

STOP

REW

PAUSE

•

REC

TV•VCR

E P

1 2 3

7 8 9

ENTER

Turn the Laserdisc Player On and Off.

1. Press VCR2•LD to set the remote to control

the Laserdisc Player.

(Most RCA and ProScan

models will only turn on when pressing

VCR2•LD not POWER).

2. Press POWER to turn the Laserdisc Player

on or off.

Watch a disc in your Laserdisc Player.

1. Turn on the Laserdisc Player.

2. Place a disc in the Laserdisc Player.

3. Press PLAY to start the disc.

4. Press STOP when you are finished.

5. Press PAUSE to pause the disc.

You may want to experiment with the

remote to determine all the buttons which

work with your Laserdisc Player.

Operating A Laserdisc Player

•

PLAY

STOP

PAUSE

Turn the Audio Equipment On and Off.

1. Press AUDIO to set the remote to control

the Audio Equipment.

(Most RCA, GE and

ProScan models will only turn on when

pressing AUDIO not POWER).

2. Press POWER to turn the Audio Equipment

on or off.

Play a tape or CD in your Audio Equipment.

1. Turn on the Audio Equipment.

2. Insert a tape or CD.

3. Press PLAY to start the tape or CD.

4. Press STOP when you are finished.

5. Press REW to rewind the tape.

6. Press PAUSE to pause the tape or CD.

You may want to experiment with the

remote to determine all the buttons which

work with your Audio Equipment.

Operating Audio Equipment

PLAY

STOP

REW

PAUSE

Operating A TV/VCR Combo Unit

Special Operations

RCA, GE and PROSCAN Brand Devices:

Many of these devices (TVs and VCRs) will not need to be

programmed. In the event that programming is required,

the code search method is suggested.

Note: With these brands, the device button (TV, VCR1, VCR2•LD,

AUDIO) will usually turn the units on. The POWER button will only

turn off the device, if you used the TV, VCR1 or AUDIO button to turn

the unit on.

SCIENTIFIC ATLANTIC Cable Boxes:

This brand of cable box can be programmed using the code search

method by using the CHANNEL UP key rather than POWER during

Code Search. NOTE: The device must be turned on prior to beginning

the code search. Once the device turns off, press and release ENTER.

In most cases this cable box can be turned on and off using the

CHANNEL UP key not the POWER button. If the unit will not turn

on using the CHANNEL UP key, then manually turn it on and

only partial compatibility will be achieved.

JERROLD or GENERAL INSTRUMENTS Cable Boxes:

These units can be programmed using the code search method.

In some cases, these devices will change channels during the

code search. Continue until the unit turns off, then press

and release ENTER.

ZENITH and OAK cable boxes

Some Zenith and Oak Cable Boxes require pressing CHANNEL

DOWN rather than ENTER after numeric entry.

Some TV/VCR combination units may be controlled by using a

combination of TV and VCR codes. For example, the Samsung TV/VCR

combo unit may be controlled by both the Samsung TV

code and the Samsung VCR code.

Andere Handbücher für RCU500

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere RCA Fernbedienung Handbücher

RCA

RCA SYSTEMLINK3 RCU1300 Bedienungsanleitung

RCA

RCA CRCU4601WM Bedienungsanleitung

RCA

RCA RCU403R Bedienungsanleitung

RCA

RCA RCRPS06GR Bedienungsanleitung

RCA

RCA RCR311BIR Betriebsanleitung

RCA

RCA RCU400R3 Bedienungsanleitung

RCA

RCA RCRPS04GR Bedienungsanleitung

RCA

RCA RCR3283 - Universal Remote Control Bedienungsanleitung

RCA

RCA RCU300 - RCU 300 Universal Remote Control Bedienungsanleitung

RCA

RCA RCR6373 Bedienungsanleitung

RCA

RCA D770 - D 770 Universal Remote Control Bedienungsanleitung

RCA

RCA RCTC4GB Handbuch

RCA

RCA RCRPS02GR Bedienungsanleitung

RCA

RCA RCRPS06GR Benutzerhandbuch

RCA

RCA RCR504BR Series Administratorhandbuch

RCA

RCA RCR002RWDZ Bedienungsanleitung

RCA

RCA RCR311SR Bedienungsanleitung

RCA

RCA RCRV06GR Bedienungsanleitung

RCA

RCA RCR311BN Betriebsanleitung

RCA

RCA RCR312W Bedienungsanleitung

RCA

RCA RCRPS06GR Bedienungsanleitung

RCA

RCA CRCU4601WM Bedienungsanleitung

RCA

RCA RCRF03B Administratorhandbuch

RCA

RCA RCRN06GR Administratorhandbuch

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung

Invacare

Invacare G91S Bedienungsanleitung